MAGNADYNE PLUS-4500 Owner's Manual

OWNER’S

MANUAL

Models: PLUS-4500

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference; and
(2) This device must accept any interference received, including interference that may cause undesired operation.

Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this
equipment. Such modifications could void the user’s authority to operate the equipment.

© Copyright 2000 Magnadyne Corporation

R

Vehicle Security

R

2

Congratulations on your purchase of a quality Carbine Automotive security system. Carbine automotive
security products have been designed to provide the consumer with a product that is technologically
superior and will provide years of trouble free operation.

The information enclosed will provide a ready reference of the operation and maintenance of your new
Carbine security system.

1. Exit the vehicle and close all entrances.

2. Press and release the LOCK button on the transmitter. The security system will respond as follows:
A. The horn/siren will chirp one time.

B. The LED indicator will begin to flash at a steady rate.
C. The parking lights will flash one time.
D. All protected entrances are armed.

Note: If the dome light is on or a sensor is active at the time you arm your security system, You will
hear the horn/siren beep one time and then you will hear another beep from the horn/siren about 5
seconds later. This second beep is the active sensor warning indicator. This second beep tells you that
the alarm is armed but one of the sensors has been temporarily deleted because it was on at the time
the alarm was armed.

The security system is now fully armed!

Your Carbine security system can operate from any one of the three transmitters shown here. Locate the
transmitter that was supplied with your system and use the drawing as a ready reference while reading
through the operating procedures.

Security System Operation: (Using the transmitter to arm the security system)

Remote Control Transmitters

R

Code
Hopping

Regular

Lock Unlock

Panic

Aux

Aux

Unlock

Lock/
Panic

C

A

R

Passive

Lock

Unlock

Panic

Aux

B

Passive

Unlocking

Note: The following information is valid only if your security system has been programmed to
automatically arm.

1. Turn off the ignition key and exit the vehicle.

2. Close all protected entrances. After the last protected entrance is closed the horn/siren will chirp one
time and the LED indicator will begin to flash fast. The fast flashing LED indicates that the automatic
arming timer is counting down and the security system will become armed within 30 seconds. After 30
seconds has passed, the security system will respond in the following manner:

A. The horn/siren will chirp one time.
B. The LED indicator will begin to flash slower.
C. The parking lights will flash one time.
D. All protected entrances are armed.

Note 1: Re-opening a protected entrance before the system becomes armed will stop the arming timer .
After closing the entrance the timer will begin counting again from zero.

Note 2: If the vehicle has a delayed interior lighting system, the automatic arming timer will start
counting after the interior lighting has turned itself off. This could add up to 45 seconds to the total
automatic arming countdown time. (Up to 75 seconds total arming delay)

The security system is now fully armed!

3

1. Press and release the UNLOCK button on the transmitter. The security system will respond as follows:
A. The horn/siren will chirp two times.

B1.The LED indicator will be off. (Only if Auto Arming is programmed off)
B2.The LED indicator will be flashing very fast. (Only if Auto Arming is programmed on)
C. The parking lights will flash two times.

Note: If you are disarming the security system after it has been triggered and the horn/siren is sounding,
the disarm chirps are automatically deleted.

Disarming the Security System Using the Passive Transmitter (B)

Note: When using the passive transmitter the “on/off” switch must be in the “on” position.

A. Walk toward your vehicle and the security system will respond the same as pushing the unlock

button on the transmitter.

The security system is now disarmed!

Automatic Arming: (Without using the transmitter)

Disarming the Security System Using the Transmitter