MAGNADYNE PL50, PL60 Owner's Manual
OWNER’S
MANUAL
Models: PL50
PL60
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference; and
(2)
This device must accept any interference received, including interference that may cause undesired operation.
Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications
to this equipment. Such modifications could void the user’s authority to operate the equipment.
© Copyright 2000 Magnadyne Corp.
Remote Mobile Security System
2
The information enclosed will provide a ready reference of the operation and maintenance of your new
security system. The operating instructions enclosed are for two security system models. Many of the
functions are similar between the models but be sure to follow the instructions that pertain to your model
security system only.
Remote Control Transmitters
“Using the Transmitter to Arm the Security System”
1. Exit the vehicle and close all entrances.
2. Press and release the ARM/DIS or the LOCK button on the transmitters. The security system will
respond as follows:
A. The horn/siren will chirp one time.
B. The LED indicator will begin to flash at a steady rate.
C. The parking lights will flash one time.
D. The starter is deactivated which prevents the engine from being started.
E. All protected entrances are armed.
F. The horn/siren will sound one additional time if the vehicle has delayed interior lights that stay on
after the door is closed.
The security system is now fully armed!
The Remote Mobile Security Systems can operate from any one of the five transmitters shown here.
Locate the transmitter that was supplied with your system and use the drawing as a ready reference while
reading through the operating procedures.
Security System Operation
A
B
D
C
R
Silent Arming
ARM/DIS
Button
AUX CH#2
Button
Silent Arming
ARM/DIS
Button
AUX CH#2
Button
Silent Arming
AUX CH#2
Button
ARM/DIS
Button
Silent Arming
ARM/DIS
Button
AUX CH#3
Button
PANIC AUX
LOCK
UNLOCK
Silent Arming
PANIC
Button
LOCK/ ARM
Button
AUX CH#2
Button
UNLOCK/
DISARM
Button
F
AUX CH#2
Button
Note: The following information is valid only if your security system has been programmed to automatically
arm.
1. Turn off the ignition key and exit the vehicle.
2. Close all protected entrances. After the last protected entrance is closed the horn/siren will chirp one
time and the LED indicator will begin to flash fast. The fast flashing LED indicates that the automatic
arming timer is counting down and the security system will become armed within 30 seconds. After 30
seconds has passed, the security system will respond in the following manner:
Note 1: Re-opening a protected entrance before the system becomes armed will stop the arming timer .
After closing the entrance the timer will begin counting again from zero.
Note 2: If the vehicle has a delayed interior lighting system, the automatic arming timer will start
counting after the interior lighting has turned itself off. This could add up to 45 seconds to the total
automatic arming countdown time. (Up to 75 seconds total arming delay)
A. The horn/siren will chirp one time.
B. The LED indicator will begin to flash slower.
C. The parking lights will flash one time.
D. The starter will become deactivated and will prevent the engine from starting.
E. All protected entrances are armed.
The security system is now fully armed!
3
Automatic Arming (Without Using the Transmitter)
Press and release the ARM/DIS or UNLOCK button on the transmitter. The security system will respond as
follows:
A. The horn/siren will chirp two times.
B. The LED indicator will be off.
C. The parking lights will flash two times.
Note: If you are disarming the security system after it has been triggered and the horn/siren is sounding,
the disarm chirps are automatically deleted.
The security system is now disarmed!
Disarming the Security System Using the Transmitter
Loading...