MAGNADYNE MV2760 User's Manual

7" & 6.4" Viewing Screen Controls and Functions

7. Stereo/Mono Switch:

If a condition of interference arises and it can not be remedied by selecting another frequency, changing the transmit mode from “Stereo” to “Mono” usually will eliminate interference noise. The audio performance will be reduced when the switch is placed in the “MO” position. Return the “ST/MO” switch to the “ST” position to re-gain the high performance stereo sound in the headphones or the Vehicles stereo system.

6. Transmitter Frequency Selection:

The Movievision viewing screen transmits a signal that is received by the Movievision headphones and can also be received by the vehicle’s car radio. There are 3 frequencies available for use. When you are listening to a movie using the wireless Movievision headphones, it is possible that you could travel through an area where interference between the screen transmitter and the headphone receiver is at an un-acceptable level. If this occurs, you can use the 3 position frequency switch located in the roof housing to select a different frequency that may have less or no interference. Each time you change the transmitting frequency, the headphone/car radio receiver will have to be re-tuned to the new frequency. The 3 frequencies available for use are 89.7mhz, 90.1mhz or 90.5mhz.

Transmitter Frequency Selection Switch

Domelight Switch

Warning! in some cases, the domelight maybe hot, proceed with caution. Only replace the bulb with the same size and wattage that you took out. Altering the size, shape or wattage will result in a damaged housing (melting). Use only Sylvania or GE model DE3021 for replacements.

Car Radio Interface:

The signal transmitted from the Movievision screen can be received by the existing FM car radio. To listen to the Movievision signal through the vehicle stereo system, repeat the following procedures:

Turn “ON” the Movievision system and insert a tape or attach an auxiliary signal

source to view on the screen.

B. Turn “ON” the FM radio in your vehicle and tune the radio to one of the 3

frequencies transmitted by the Movievision system. (89.7mhz - 90.1mhz - 90.5mhz)

C. Adjust the volume and tonal qualities to suit your listening taste.

Domelight Operation:

(Applies to MovieVision flip-down screen with dome lights built-in only.) The dome light(s) located in the MovieVision screen housing will illuminate

whenever the vehicle doors are open just as the original domelight did. To activate the dome lights while the vehicle is in motion, press the domelight switch next to the position.

Note: Most American made vehicles (Ford, Chevrolet, Dodge) have a dashboard light dimmer switch that can be rotated to the maximum position and the dome lights will illuminate. Most Japanese or Korean made vehicles do not have this switch and the lights will have to be turned on manually as mentioned above.

1. Infrared Eye

Point the remote control in the direction of the Infrared Eye when accessing the functions provided by the remote control.

2. Viewing Screen Release

To release the screen, push inward on the MovievisionTMlogo and pull downward. Place the screen to the desired viewing position.

3. Adjusting the Screen’s Color Intensity:

Rotate t

he color control to the left or right to change the intensity of the colors on the screen. Rotation to the left (-) will reduce the color and rotation to the right (+) will increase the color. Adjust

the color of the screen to your desired taste.

4. Adjusting the Screen’s Contrast: (CONTR) Rotate the contrast control to the left or the right to change the intensity of the dark colors compared to the light colors and vise versa.

5. Adjusting the Screen’s Brightness:

Rotate the bright (brightness) to the left or the right to change background lighting of the screen from darker to lighter and vise versa.

7.0"MV-POD7

6.4"MV-POD2

MV-POD2

MV-POD7

MV-POD2

MV-POD7

MV-POD2

MV-POD7

Stereo/Mono Switch

Digital Headphone Operation

1. Turn On the Headphones:

To turn on the headphones, press the ”PWR” button on the right side ear pad. The digital display will show radio station digits when the headphone is on.

2. Tuning an FM Radio Station:

A. Press the ”UP” or ”DOWN” button to

manually tune in an FM radio station.

B. Press and hold the ”UP” or ”DOWN”

button for one second then release. The radio tuner will search up or down the radio band for the next strongest FM radio station. Note: FM radio stations are always received in Stereo Mode.

C. Adjust the volume knob to the desired volume level.

Plug for second pair of headphones

3. Listening to What Is Displayed on the Viewing Screen:

On the right ear pad are 3 pre-programmed buttons marked 1, 2 and 3. These buttons will tune the headphone radio to the exact MovieVision signals. Press the buttons one at a time until what you hear in the headphones is what is displayed on the viewing screen.

4. Turn Off the Headphones when you are Finished:

A. Press the ”PWR” button to turn off

the headphones.The display will be blank when the headphones are off.

B. The batteries supplied with your

MovieVision headphones will last for approximately 10 hours of continuous use. Forgetting to turn off the headphones when they are not in use will decrease the battery life.

Volume Control

5. Connecting a Second Set of Headphones

Your Movievision headphones have a plug receptacle located at the side of the “L” ear pad. A second set of personal type headphones (Must have 3.5 mini male type plug) can be connected at this point.

Note: When a second pair of headphones are attached, the tuning and audio level is controlled by the Movievision headphone.

Your Movievision entertainment system is supplied with two (2) Movievision headphones. The correct operation, care and maintenance of the headphones is critical to their ability to provide the user with a lifetime of operation. Misuse, abuse and neglect of the headphones will result in poor performance and premature failure. NOTE: Please read through the simple operation and maintenance instructions enclosed.

WARNING!

• Do not throw the headphones.

• Do not get the headphones wet or submerse them in any liquid.

• Do not step, stand or sit on the headphones.

1. Install the Batteries (AAA Type)

To install the “AAA” batteries supplied, repeat the following procedure:

A. Place your thumb onto the gripping arrow on the battery holder cover. B. Press down on the gripping arrows while pulling downward. Slide the door

away from the headphones to expose the battery holder cavity.

C. Place the batteries into the holder following the directions engraved inside the

holder. Observe battery polarity.

2. Adjust the Headphones to Fit Your Head

Repeat the following to adjust the headband to fit:

A. Spread the ear pads apart and place the headphones on your head. Observe

the “L” and “R” indicators.

B. Grab the ear pads and use your thumb and forefinger to slide the adjusters up or

down until a comfortable fit is achieved.

MV-USER2000

Rev. B 1-7-03