Page 1
USER
MANUAL
Model: MCD55C
Remote Mobile Security System
© Copyright 1997 Magnadyne Corporation
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference; and
(2) This device must accept any interference received, including interference that may cause undesired
operation.
Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized
modifications to this equipment. Such modifications could void the user’s authority to operate the
equipment.
MCD55UM 08/02/00 3:10 PM Page 1
Page 2
LOCK
PANIC
UN
LOCK
AUX
LOCK
PANIC
UN
LOCK
AUX
Dedicated Button Mode
2
Congratulations on your purchase of a quality automotive security system. This security system
has been designed to provide the consumer with a product that is technologically superior and will
provide years of trouble free operation.
The information enclosed will provide a ready reference of the operation and maintenance of your
new security system.
Enclosed, is an illustration of the transmitter supplied and the function of each button. Your
transmitter can operate one of two ways as shown. The most common operation is the “A” mode.
This mode provides “Dedicated Buttons” to perform the alarm functions. Each button is engraved
with it’s function. “B” mode is an alternative operation mode that is only used when multiple alarm
control is necessary (operating more than one alarm) or when a channel 3 output is required.
1. Locks doors, arms alarm and will activate
the personal remote panic system.
2. Unlocks doors and disarms alarm.
3. Activates channel #2 for optional
accessories.
- Press Aux before pressing LOCK or
UNLOCK to initiate silent arming or
silent disarming.
- In this mode, multi-vehicle operation is
not possible
1. Arms and disarms alarm. Locks and
unlocks doors, activates the remote
personal panic system.
2.
Activates channel #2 for optional accessories.
3.
Activates channel #3 for optional accessories.
- Press Aux before pressing LOCK to initiate
silent arming or silent disarming.
- In this mode, the transmitter is capable
of operating a second vehicle alarm.
Remote Control Transmitters
A
LOCK
PANIC
UN
LOCK
AUX
LOCK
PANIC
UN
LOCK
AUX
Separate Channel Mode
B
MCD55UM 08/02/00 3:10 PM Page 2
1
☛
UN
LOCK
LOCK
PANIC
AUX
3
☛
2
☛
1
☛
LOCK
PANIC
AUX
UN
LOCK
2
☛
3
☛
Page 3
3
Using the transmitter to arm the security system
1. Exit the vehicle and close all entrances.
2. Press and release the LOCK button on the transmitter. The security system will respond as
follows:
A. The horn/siren will chirp one time.
B. The LED indicator will begin to flash at a steady rate.
C. The parking lights will flash one time.
D. All protected entrances are armed.
The security system is now fully armed!
Security System Operation
Without Using the Transmitter
Note: The following information is valid only if your security system has been programmed to
automatically arm.
1. Turn off the ignition key and exit the vehicle.
2. Close all protected entrances. After the last protected entrance is closed the horn/siren will chirp
one time and the LED indicator will begin to flash fast. The fast flashing LED indicates that the
automatic arming timer is counting down and the security system will become armed within 30
seconds. After 30 seconds has passed, the security system will respond in the following
manner:
A. The horn/siren will chirp one time.
B. The LED indicator will begin to flash slower.
C. The parking lights will flash one time.
D. All protected entrances are armed.
Note 1: Re-opening a protected entrance before the system becomes armed will stop the arming
timer. After closing the entrance the timer will begin counting again from zero.
Note 2: If the vehicle has a delayed interior lighting system, the automatic arming timer will start
counting after the interior lighting has turned itself off. This could add up to 45 seconds to the total
automatic arming countdown time. (Up to 75 seconds total arming delay)
The security system is now fully armed!
Automatic Arming
MCD55UM 08/02/00 3:10 PM Page 3
Page 4
4
The valet switch is used to override the security system in the event that the transmitters are lost or
fail to operate and to put the security system in non-operational mode (valet) for vehicle servicing
etc.
Override Operation: (Security System is Armed)
1. Enter the vehicle. (The security system will begin sounding at this point)
2. Place the ignition key into the ignition switch and turn the ignition switch to the “on” position.
3. Within 5 seconds of turning the ignition key “on”, place the valet switch to the “on” position.
4. The horn/siren will stop sounding.
5. The LED indicator will be solid red.
The security system is overridden and is now in the valet mode!
Note 1: If the valet switch is already in the “on” position when you turn “on” the ignition key, the
override function will be bypassed. Turn “off” the ignition key, place the valet switch in the “off”
position and try again.
Note 2: If you fail to place the valet switch to the “on” position within 5 seconds of turning “on”
the ignition key, the override function will be locked out. Place the valet switch in the “off”
position, turn “off” the ignition key and try again.
Valet Operation: (The security system is already disarmed)
1. Turn the ignition key to the “on” position.
2. Place the valet switch to the “on” position.
3a. The LED will be on solid indicating that the security system is in the valet mode. (Ignition key
“on”)
3b. The LED will flash once every 5 seconds indicating the security system in valet mode.
(Ignition key off)
Valet/Override Switch Operation
1. Press and release the UNLOCK button on the transmitter. The security system
will respond as follows:
A. The horn/siren will chirp two times.
B1. The LED indicator will be off. (Only if Automatic Arming is programmed off)
B2. The LED indicator will be flashing very fast. (Only if Automatic Arming is programmed on)
C. The parking lights will flash two times.
Note: If you are disarming the security system after it has been triggered and the horn/siren is
sounding, the disarm chirps are automatically deleted.
The security system is now disarmed!
Disarming the Security System Using the Transmitter
MCD55UM 08/02/00 3:10 PM Page 4
Page 5
5
Press and hold the LOCK button for more than 3 seconds and the security system will respond in
the following manner:
A. The horn/siren will begin sounding.
B. The parking lights will begin flashing.
To turn off the panic alarm, press and release the UNLOCK button on the transmitter. The horn/siren
will stop sounding and the parking lights will stop flashing.
Note: If you do not turn off the panic feature with the transmitter, the panic alarm will sound for 60
seconds and then turn off by itself.
Your security system can be instructed to become armed or disarmed without the horn/siren chirps
by the remote transmitter. To operate this feature at any time, simply press and release the AUX
button then press the LOCK or UNLOCK button to arm or disarm your security system without the
chirp indications.
If your security system has become triggered, the horn/siren will sound for 60 seconds and then
stop and re-set to a fully armed condition.
Note: If a protected entrance is left open, your security system will remain triggered for two more
60 second cycles then fully re-arm excluding the door input trigger. (Door input trigger is no longer
functional) Closing the entrance will re-set the door input trigger within 7 seconds.
Every time you disarm your security system with your transmitter, the security system will start an RF
protection mode countdown. This is a timed secondary protection mode to insure that the radio signal
used to disarm the security system was from your transmitter. After the system is disarmed by radio
signal, it will count down for 60 seconds and then become re-armed if no one enters the vehicle.
Note: The feature is only active when the security system has been programmed to automatically arm.
How to Get Back to Security System Activation Mode:
1. Place the ignition key switch to the “on” position.
2. Place the valet switch to the “off” position.
3. Place the ignition key switch back to the “off” position. You will notice that the LED indicator
will be off. This indicates that you have exited the valet mode and your security system will
operate normally.
Valet/Override Switch Operation
User Discretion Silent Arming
60 Second Re-Arming
Remote Panic
Secondary RF Protection Mode
MCD55UM 08/02/00 3:10 PM Page 5
Page 6
6
Option #1: Remote Power Door Lock/Unlock Control
Note: Your vehicle must have an electronic door locking system for this feature to operate.
Installing option #1 will allow the remote transmitter supplied with your security system to lock
and unlock your vehicle’s doors as it arms and disarms your security system.
Option #2: Remote Trunk/Hatch Release (Channel #2)
Installing option #2 will allow the remote transmitter supplied with your security system to open
your vehicles trunk or rear hatch. Pressing the “AUX ” button on the transmitter for 2 seconds will
open the existing power trunk/hatch release mechanism.
Note: Vehicles that are not factory equipped with an electronic trunk release system will require
additional parts than a vehicle with a factory installed trunk release system.
Option #3: Dome Light Illumination
Installing option #3 will allow your security system to turn on your vehicles interior illumination
system at the time the security system is disarmed by the remote transmitter. The interior lighting
will remain on for 30 seconds after the security system is disarmed. Turing on the ignition key will
turn off the interior illumination before 30 seconds.
Alarm Mode Indicators
1.The LED indicator will provide information on 9 modes of security system operation:
LED is off = Alarm is disarmed.
LED is flashing = Alarm is armed.
LED is flashing in a 1 flash hold sequence = Tamper warning, alarm was triggered by the current
sensing sensor.
LED flashing in a 2 flash hold sequence = Tamper warning, alarm was triggered by the hood or
trunk.
LED flashing in a 3 flash hold sequence = Tamper warning, alarm was triggered by an opened
door.
LED flashing in a 4 flash hold sequence = Tamper warning, alarm was triggered by an electronic
sensor.
LED is on steady = Alarm is in the valet mode. (Ignition key is “on”)
LED flashes once every 5 seconds = Alarm is in the valet mode. (Ignition key is off”)
LED is flashing fast = Automatic arming timer is counting down or RF tamper rearming timer is
counting down.
2. The horn/siren will provide information on four modes of security system operation.
One horn/siren chirp = Security system is armed.
Two horn/siren chirps = Security system is disarmed.
Four horn/siren chirps = Tamper warning + security system is disarmed.
Upgrade Options
MCD55UM 08/02/00 3:10 PM Page 6
Page 7
7
The following is a brief description of the operation of each programmable feature. Any adjustment
to the operation of these features must be performed by the dealer who installed your Security
System. These features are not user adjustable.
Ignition Key Controlled Door Lock/ Unlock: (Remote door lock/unlock option must be
installed)
With this feature activated, the door lock system of the vehicle will become locked 3 seconds after
the ignition key is turned to the on position (All doors). When the ignition key is turned to the off
position, the door locks will immediately become unlocked.
Note: This feature has 3 modes in which it can operate. Mode #1 operates as explained above and
is the most common operation. Model #2 locks the doors when the ignition key is turned on but
does not unlock the doors when the ignition key is turned off. In mode #3 the ignition key locking
feature is off.
Option #4: Single Zone Shock Sensor
Installing option #4 will increase the level of security provided by your security system. If the
shock sensor becomes activated the security system will immediately trigger your security
system by sounding the horn/siren and flashing the parking lights.
Option #5: Starter Disable Relay
Adding option #5 will increase the level of protection that your security system can offer. When
the starter disable relay is installed, the vehicles engine will not crank when the alarm system is in
the armed mode.
Option #6: Unlock Drivers Door First (Requires option #1 to be installed.)
Installing option #6 will allow your security system to unlock only the drivers door upon
disarming the security system. To unlock the remaining doors, press the UNLOCK button once
again within 3 seconds of disarming the security system. The remaining doors will become
unlocked.
Option #7: Dual Zone Shock Sensor
Installing option #7 will increase the level of security provided by your security system. Zone #1
of the dual zone shock sensor will detect lighter non-threatening disturbances that would normally
set off most sensors and trigger the security system. If zone #1 is activated the security system
will emit a single chirp from the horn/siren. This single chirp is a pre-warning if a would be thief is
attempting to enter your vehicle. Zone #2 detects heavier impacts that are considered threatening
and immediately triggers your security system by sounding the horn/siren and flashing the
parking lights.
Upgrade Options:
(Continued)
Programmable Features
MCD55UM 08/02/00 3:10 PM Page 7
Page 8
8
Chirp Status Indicator Delete: (Permanent Chirp Delete)
De-activating the chirp indication system will eliminate the arm and disarm chirp indicators. For
your safety, the tamper warning chirp indicator will always be active.
Automatic Arming of Security System:
When the automatic arming of security system feature is programmed on, the security system will
automatically become armed 30 seconds after the last protected entrance is closed without
requiring a signal from the remote transmitter. (Ignition switch must be off)
Automatic Door Locking: (Remote door lock/unlock option must be installed)
If it is desired to have the vehicle’s power door locking system become locked at the same time
the security system becomes armed by the automatic arming of security system feature, the
automatic door locking programming should be on.
Safety Illumination:
Programming on the Safety Illumination System will proved the vehicle user with a lighted
pathway to and from the vehicle when the security system is armed and disarmed.
When programmed on, the parking lights and the dome light will remain on for 12 seconds after
the security system is armed providing a lighted pathway while leaving the vehicle.
In addition, the parking lights and dome light will remain on for 30 seconds after the security
system is disarmed immediately drawing attention to your vehicle while providing a fully lighted
vehicle interior and exterior.
Programmable Features:
(Continued)
MCD55UM 08/02/00 3:10 PM Page 8
Page 9
System Maintenance:
The only maintenance that your security system requires is a periodic check of it’s operation to be
sure that all functions are operating properly. The batteries supplied with your transmitter will
usually last about 1 year. Heavier usage will shorten battery life. Reduced transmitter range is
usually a sign that the battery in the transmitter is becoming weak and should be replaced.
Battery Replacement:
Replacement batteries for your transmitter are available in most drug stores and camera shops.
To replace the battery, remove the small Phillips screw from the transmitter case and pull apart
the top and bottom case halves. Remove the battery from it’s holder. Insert the new battery in
place of the old one observing the batteries +/- polarity. Gently snap the top and bottom case
halves together (DO NOT force them together) and replace the Phillips screw (DO NOT over
tighten the screw)
Replacement Transmitters:
In the event that the transmitter supplied with your security system becomes damaged or lost,
return to the installation facility that installed your security system to purchase a new one.
Maintenance
9
MCD55UM 08/02/00 3:10 PM Page 9
Page 10
Limited Lifetime Warranty
Magnadyne Corporation or its authorized agents will, for the life of the vehicle and to the
original purchaser, repair, replace or refund the retail sales price of said product or any
part thereof, at the option of the Magnadyne Corporation or its authorized agents, if said
product or part is found defective in materials or workmanship, when properly connected
and operating on the correct power requirements designated for the specific product. This
warranty and Magnadyne Corporation or its authorized agents obligations, hereunder do
not apply where the product was: damaged while in the possession of the consumer,
subjected to unreasonable or unintended use, not reasonably maintained, utilized in
commercial or industrial operation, or serviced by anyone other than Magnadyne
Corporation or its authorized agent, or where the warning seal on the product is broken or
the power plugs or wires are detached from the unit. Magnadyne Corporation or any of its
authorized agents do not assume any labor costs for the removal and reinstallation of any
product found to be defective, or the cost of transportation to Magnadyne Corporation or
its authorized agents. Such costs are the sole responsibility of the purchaser.
This warranty does not cover the cabinet, appearance items, normal wear and tear or
accessories used in connection with the product resulting from improper installation,
alteration, accident, misuse, abuse or acts of nature.
This Limited Life Time Warranty applies only to the receiver section of the security
system. Neither the siren, transmitters, wire harness or any accessory item added to or
used with a Remote Mobile security system are covered by this Limited Life Time
Warranty. Sirens, transmitters, wire harness or any accessory item are covered by our
standard 12 month limited warranty.
Magnadyne Corporation or its authorized agents shall not be liable to anyone for
consequential or incidental damages or claims that may arise due to failure of product
to operate properly except those accorded by law. Magnadyne's or its authorized
agents liability to the repair, replacement of the product as stated above if all
conditions of the warranty are met. No expressed warranty or implied warranty is
given except those set forth herein. Magnadyne does not warrant or guarantee against
break in damage or the theft of the vehicle in part or whole, or against the loss or
damage to the contents of any vehicle in which a security system is installed.
Magnadyne security systems are only a deterrent against possible theft.
This warranty extends only to the original purchaser of the product and for the vehicle in
which it was originally installed. This warranty is not transferable or assignable to any
person or vehicle. Defective merchandise should be returned to the original point of
purchase or secondly to Magnadyne Corporation, 1111 W. Victoria Street, Compton, CA
90220. A return authorization must be obtained before sending, or merchandise may be
refused.
MCD55UM 08/02/00 3:10 PM Page 10
Page 11
Replacement Parts and Accessories
for Remote Mobile Security Systems
DESCRIPTION MODEL # PRICE
Replacement Battery: For all Remote Mobile
transmitters. 1 battery needed per
ALA-BATT/P
$4.95 ea.
transmitter. (4 pieces minimum order)
Replacement Transmitter: For all
Remote Mobile 3-button security systems. MD-RF3 39.95 ea.
Model: MCD55C
1-Tone Mini 110dB Siren: For use with
Remote Mobile Security System.
(Interior Siren)
ALA103 8.95 ea.
1-Tone, 118dB Siren: For use with
Remote Mobile Security System
ALA115 29.95 ea.
6-Tone, 130dB Siren: For use with
Remote Mobile Security System
ALA125 39.95 ea.
6-Tone, 130dB Programmable Siren:
Built-In battery backup for all alarms
models. Self-charging battery with ALA145 79.95 ea.
built-in valet key and 30 minute
battery capacity.
ORDER
BY MAIL
a
l
k
al
i
n
e
b
a
tt
e
r
y
LOCK
PANIC
UN
LOCK
AUX
MCD55UM 08/02/00 3:10 PM Page 11
Page 12
Parts and Accessories Order Form
Send Check or Money Order Only (No Cash) To:
Magnadyne Corporation
ATTN: Consumer Parts Sales
P.O. Box 5365
Carson, CA 90749-5365
SHIP TO: (No P.O. Boxes)
LAST NAME FIRST NAME INITIAL
STREET ADDRESS
ADDITIONAL ADDRESS
ADDITIONAL ADDRESS
CITY STATE ZIP CODE
DAY TIME PHONE NUMBER
PAR
T # DESCRIPTION
QTY. PRICE EACH TOTAL
Sales Subtotal = ________ . ______
California Residents Add Sales Tax = ________ . ______
Shipping and Handling (See Chart) = ________ . ______
TOTAL = ________ . ______
No C.O.D.’s
On regular orders please allow 4-5 weeks for delivery.
Please give a shipping address where this order may be delivered between the hours of 9 am and 5 pm weekdays.
If UPS is unable to deliver, your order will be returned and additional shipping charges will be required.
Shipping and Handling
Subtotal + Tax Add
Up to $20.00 $5.00
20.01 to 30.00 5.95
30.01 to 45.00 6.50
45.01 to 70.00 6.95
Over 70.01 7.95
MCD55UM
7-30-97 rev. A
MCD55UM 08/02/00 3:10 PM Page 12
Page 13
Programmable Features:
Automatic Carjacking Alarm:
Programming on the automatic carjacking feature allow the alarm system to protect the driver of the vehicle when the vehicle is in
use. If an attempt is made to HIJACK the vehicle, the enclosed sequence of events will take place. It is strongly advised that you
perform the enclosed test to keep yourself familiar with the
operation of this system as well as insuring that the system is operating properly.
1. Enter the vehicle and close all the entrances. (If the vehicle has domelight delay, wait for the domelight to go out before
beginning the test)
2. Set the ignition key to the on position. Wait 5 seconds and open the driver’s door then close it.
3.
Within 50 seconds the horn/siren will begin to beep (Short Pulses). This is pre-warning that the carjacking alarm will become fully
triggered within 10 seconds.
Note: At this point, the carjacking alarm can be disabled by setting the valet switch to the on position.
4. Within 10 seconds, the carjacking alarm will be fully triggered. The horn/siren will sound normally, the parking lights will begin
flashing and the starter disable will be engaged.
5. Turn the ignition key off, then back on
6. Set the valet switch to the on position and the siren/horn will stop sounding
and the parking lights will stop flashing.
WARNING! When the carjacking alarm is programmed on, every time the ignition key is on and a door gets opened, the 50 second
timer will begin counting. If a door is open (domelight is on) before the ignition key is turned on, the 50 second timer will not start
counting until the door is closed and re-opened.
Remote Mobile Security System
Addendum to
Owner’s Manual
Model: MCD55C/P3
MCD55CP3UM-A
Rev. A 3-12-01
© Copyright 2001
Magnadyne Corporation
Loading...