MAGNADYNE MC55 Owner's Manual

Owner’s

Manual

Models: MC45

MC45H

MC55

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference; and (2) This device must accept any interference received, including interference that may cause undesired operation.

Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.

LOCK PANIC

LOCK

AUX

LOCK PANIC

LOCK

AUX

Congratulations on your purchase of a quality Marksman automotive security

LOCK PANIC

LOCK

AUX

LOCK PANIC

LOCK

AUX

system. Marksman automotive security products have been designed to provide the consumer with a product that is technologically superior and will provide years of trouble free operation.

The information enclosed will provide a ready reference of the operation and maintenance of your new Marksman security system.

Remote Control Transmitters

All three Marksman alarm models covered in this owners manual operate from the same transmitter. Enclosed, is an illustration of the transmitter supplied and the function of each button. Your Marksman transmitter can operate one of two ways as shown. The most common operation is the “A” mode. This mode provides “Dedicated Buttons” to perform the alarm functions. Each button is engraved with it’s function. “B” mode is an alternative operation mode that is only used when multiple alarm control is necessary (operating more than one alarm) or when a channel 3 output is required.

Dedicated Button Mode

LOCK

PANIC

AUX

☛

1. Locks doors, arms alarm and will activate the personal remote panic system.

2. Unlocks doors and disarms alarm.

3. Activates channel #2 for optional accessories.

- Press AUX before pressing LOCK or UNLOCK to initiate silent arming or silent disarming.

- In this mode, multi-vehicle operation is not possible

☛

Separate Channel Mode

LOCK

PANIC

☛

1. Arms and disarms alarm. Locks and unlocks doors, activates the remote personal panic system.

Activates channel #2 for optional accessories.

Activates channel #3 for optional accessories.

- Press AUX before pressing LOCK to initiate silent arming or silent disarming.

- In this mode, the transmitter is capable of operating a second vehicle alarm.

AUX

☛

Security System Operation

Using the transmitter to arm the security system

1. Exit the vehicle and close all entrances.

2. Press and release the LOCK button on the transmitter. The security system will respond as follows: A. The horn/siren will chirp one time. B. The LED indicator will begin to flash at a steady rate. C. The parking lights will flash one time. D. All protected entrances are armed.

The security system is now fully armed!

Automatic Arming

Without using the transmitter

Note: The following information is valid only if your security system has been

programmed to automatically arm.

1. Turn off the ignition key and exit the vehicle.

2. Close all protected entrances. After the last protected entrance is closed the horn/siren will chirp one time and the LED indicator will begin to flash fast. The fast flashing LED indicates that the automatic arming timer is counting down and the security system will become armed within 30 seconds. After 30 seconds has passed, the security system will respond in the following manner:

A. The horn/siren will chirp one time. B. The LED indicator will begin to flash slower. C. The parking lights will flash one time. D. All protected entrances are armed.

Note 1: Re-opening a protected entrance before the system becomes armed will stop the arming timer. After closing the entrance the timer will begin counting again from zero.

Note 2: If the vehicle has a delayed interior lighting system, the automatic arming timer will start counting after the interior lighting has turned itself off. This could add up to 45 seconds to the total automatic arming countdown time. (Up to 75 seconds total arming delay)

The security system is now fully armed!

Disarming the Security System Using the Transmitter

1. Press and release the UNLOCK button on the transmitter. The security system will respond as follows:

A. The horn/siren will chirp two times. B1. The LED indicator will be off. (Only if Auto Arming is programmed off) B2. The LED indicator will be flashing very fast. (Only if Auto Arming is

programmed on)

C. The parking lights will flash two times.

Note: If you are disarming the security system after it has been triggered and the horn/siren is sounding, the disarm chirps are automatically deleted.

The security system is now disarmed!

Valet/Override Switch Operation

The valet switch is used to override the security system in the event that the transmitters are lost or fail to operate and to put the security system in nonoperational mode (valet) for vehicle servicing etc.

Override Operation: (Security System is Armed)

1. Enter the vehicle (The security system will begin sounding at this point)

2. Place the ignition key into the ignition switch and turn the ignition switch to the “on” position.

3. Within 5 seconds of turning the ignition key “on”, place the valet switch to the “on” position.

4. The horn/siren will stop sounding.

5. The LED indicator will be solid red.

The security system is overridden and is now in the valet mode!

Note 1: If the valet switch is already in the “on” position when you turn “on” the ignition key, the override function will be bypassed. Turn “off” the ignition key, place the valet switch in the “off” position and try again.

Note 2: If you fail to place the valet switch to the “on” position within 5 seconds of turning “on” the ignition key, the override function will be locked out. Place the valet switch in the “off” position, turn “off” the ignition key and try again.

Valet Operation: (The security system is already disarmed)

1. Turn the ignition key to the “on” position

2. Place the valet switch to the “on” position.

3a. The LED will be on solid indicating that the security system is in the valet

mode. (Ignition key “on”)

3b. The LED will flash once every 5 seconds indicating the security system in in

valet mode. (Ignition key off)

+ 8 hidden pages