MAGNADYNE M5A2WP Owner's Manual

For Technical Assistance, please call [phone],

or visit www.magnadyne.com

2-Way Transmitter

User’s Manual

(Upgrade for M5A only)

Model: M5A2WP

Transmitter Button System Function Remark

Lock Doors & Arm System

Arm and Delete the 2 Stage Shock Sensor Press Twice within 3 Seconds

Silent Arm

Unlock Doors & Disarm System

Two Steps Door Unlock & Disarm System Press Twice within 3 Seconds

Silent Disarming

(2 Second) Trunk Release (Channel 2) Press and Hold for 2 Seconds

(3 Second) Panic Function Press and Hold for 3 Seconds

Channel # 3 Output

2

Congratulations on your purchase of a quality Marksman automotive security system. Marksman
security products have been designed to provide the consumer with a technologically superior
product with years of trouble free operation. The information enclosed will provide a ready
reference of the operation and maintenance of your new Marksman security system.

Note: The enclosed information pertains to the use and programming of the M5A2WP transmitter
only. The standard transmitter use and programming can be found in the M5A user's manual.

-

-

-

As with any product that performs automatic functions, there are certain safety precautions that
you must be aware of and practice.

1. Keep the transmitter out of children’s reach.

2. Do not leave anyone in the vehicle while running on remote control.

3. Alert servicing personnel that the vehicle can be started automatically.

4. Do not start the vehicle by remote while it’s in an enclosed area or garage.

5. Always apply the parking brake and lock the vehicle as you exit the vehicle.

6. The vehicle windows must be rolled up.

7. Should the unit malfunction, disconnect the fuse until the problem is corrected.

8. The use and operations of this system is the sole responsibility of the operator.

9. Some areas may have local ordinances that prohibit leaving a vehicle running on public streets.

WARNINGS

Remote Transmitter Dedicated Button Operation

-

Note: The factory default setting is Power Save Mode. Before operating the 2-way LED remote
control transmitter, first press the button, within 3 seconds press and hold the button
for 3 seconds. Two beeps indicate exit of the Power Save Mode. Now, all transmitter functions will
operate normally.

+

Transmitter Button System Function Remark

(2 Second) Button Lock

Press within 3 Seconds and Hold

Button for 2 Seconds

(C) System’s Status Check Press within 3 Seconds

(2 Second) Melody Sound On/Off

Press within 3 Seconds and Hold

Buttons for 2 Seconds

(M) Last Trigger Memory Retrieval Press within 3 Seconds

(3 Second)

Power Save Mode

Press within 3 Seconds and Hold

Buttons for 3 Seconds

Switching Code for 2nd/1st Car

Press within 3 Seconds and Hold

Operation

and Buttons for Together

for 2 Seconds

3

2-Way LED Remote Control Transmitter Operation Only

-

-

-

-

-

-

-

+

(2 Second)

1. Press the button on the transmitter.

2. The siren will chirp once and parking light will flash once indicating that the system is now
armed. The vehicle’s doors will lock upon arming when interfaced with the security system.

Actions of the 2-Way LED Remote Control Transmitter

Arm LED Melody Sound

Arm LED turns on for 2 seconds One Chirp

Arm and Hood/Trunk Ajar LED flashes for 15 seconds Three Chirps

Arm and Door Ajar LED flashes for 15 seconds Three Chirps

Active Arming (Lock and Arm)

Ajar Warning:

If the siren sounds 3 chirps, then you have left a door, trunk, or hood ajar.

Shock Sensor Bypass:

Press the button on the transmitter 2 times, then within 3 seconds to arm the security system
and bypass the shock sensor. The system will chirp 1 additional time to confirm the Shock Sensor
Bypass Mode was activated. The sensor bypass feature is programmed to activate for one arming
cycle only. The security system will return to normal operation during the next arming cycle.

Silent Arming:

Press the button first, within 3 seconds press the button to arm your security system. No
chirp sound will be heard, and the arm confirmation will be through the vehicles parking lights
and the LED on the 2-way transmitter.

1. Press the button on the transmitter.

2. The siren will chirp twice and parking lights will flash twice indicating that the security system is
now disarmed.

Active Disarming (Unlock and Disarm)

LED Melody Sound

Disarm LED turns on for 2 seconds 2 Chirps

Hood/Trunk Trigger LED flashes for 15 seconds 4 Chirps

Door Trigger LED flashes for 15 seconds 4 Chirps

Shock Sensor Trigger LED flashes for 15 seconds 4 Chirps

Ignition Trigger or

LED flashes for 15 seconds 4 Chirps

Voltage Drop Trigger

Silent Disarm:

Press the button first, within 3 seconds press the button to disarm your security system.
No chirp sound will be heard, and the disarm confirmation will be through the vehicles parking
lights and the LED on the 2-way transmitter..

Tamper Disarming:

If the alarm is triggered upon disarming the system, the siren will chirp 4 times and the parking
lights will flash 3 times.

Two Step Door Unlock (if installed):

This feature will independently unlock the driver’s door only when disarming the security system.
Pushing the button a second time within 3 seconds will unlock the other doors.

Actions of the 2-Way LED Remote Control Transmitter

The valet switch allows you to temporarily bypass all alarm functions, eliminating the need to give
your transmitter to parking attendants or garage mechanics. When the system is in Valet Mode, all
alarm functions and remote start functions are bypassed. However, the remote panic feature and
remote door locks will remain operational. To use the Valet Mode, the system must be disarmed
either by using you remote transmitter, or by operating the manual override sequence.

Enter Valet Mode:

1. From the disarmed mode, turn the ignition to the “On” position.

2. Push and hold the valet switch for 2 seconds until the LED turns “On”. The LED will remain on
as long as the system is in Valet Mode.

Exit Valet Mode:

1. To return to normal operation, turn ignition “On”.

2. Push and hold valet switch for 2 seconds. The LED will turn “Off” indicating the system has
exited Valet Mode.

Actions of the 2-Way LED Remote Control Transmitter

Valet Mode (System in Disarm Mode)

LED Melody Sound

Remote Door Lock Zzz LED turns on for 2 seconds 1 Chirp

Remote Door Unlock

Zzz LED turns on for 2 seconds 2 Chirps