Magnadyne Aquavibe MD-150, Aquavibe MD-250, Aquavibe MD-350 Operation And Installation Manual

Operation

and Installation

Manual

Models: MD-150

MD-250
MD-350

Deluxe Entertainment Center

with Docking Station

MODE

RDM

RPT

SEL

TRACK

VOL

Charge Only

Aux In 1

Reset

Please take the time to read all of the information in this manual. Familiarity with operation and installation
procedures will help you obtain the best possible performance from your new Entertainment Center.

Introduction

2

Index

Button Locations and Functions ..................................................... 3-4

Remote Control Button Locations and Functions ........................................ 4

General Operation ................................................................ 5

Sound Controls .................................................................. 5-7

Using an IPHONE or IPOD .......................................................... 7-9

Using a Device with 3.5mm Output ................................................... 8-9

Bluetooth Operation ............................................................... 10

External Rear Audio Input .......................................................... 10

Radio Operations ................................................................. 11-12

Reset .......................................................................... 13

Inserting a Battery into Remote Controller ............................................. 13

Programming a Wireless Remote Controller ............................................ 13

Installation ...................................................................... 14

Wiring ......................................................................... 15

Warranty ....................................................................... 16

Warnings

• This unit is only IPX5 waterproof when the access

door is closed. When connecting a device avoid water
getting inside the waterproof compartment. Water in
the waterproof compartment may damage this unit,
cause electrical shock or fire.

• To prevent a short circuit never put or leave any

metallic objects or unconnected 3.5mm or USB cables
inside the unit.

• Use the proper power supply. This product is designed

for operation with a negative grounded 12V DC sys­tem only. Never operate this product with other power
supplies, especially a 24V DC. If the product is used
with the improper power supply it may cause a fire.

• Thi

s product must be installed and used in accordance
with this manual. Magnadyne Corporation disclaims
any and all liability that may result from failure to
install and operate in any other manner in which this
unit was intended.

•

To prevent fire or electrical shock hazard, do not

remove cover or bottom screws. No user-serviceable
parts inside. Refer servicing to qualified person

nel.

• FCC REGULATIONS STATE THAT ANY UNAUTHORIZED
CHANGES OR MODIFICATIONS TO THIS EQUIPMENT MAY
VOID THE USER’S AUTHORITY TO OPERATE IT.

• THIS DEVICE IS INTENDED FOR CONTINUOUS OPERATION.

• TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK AND
ANNOYING INTERFERENCE, USE ONLY THE RECOMMENDED

ACCESSORIES.

MODE

SEL

TRACK

VOL

Charge Only

Aux In 1

With the Door Open

the Interior

Compartment

IS NOT Waterproof

RDM

RPT

Button Locations and Functions

3

1. Power and Mode Button:
Power Button: Press to turn the entertainment

center on. Press and hold the button for 2
seconds to turn the unit off.

Mode Button: Press to select between input

sources:

Radio: FM tuner.
IPOD: 30-pin connector. (Can be selected

only when connected to a device).
Aux in 1: 3.5mm jack.
Aux in 2: Rear RCA connectors.
Bluetooth: Wireless connectivity.

2. Random Button (RDM): Press the button

for

random controls in IPOD and Bluetooth modes.

3.

Repeat Button (RPT):

Press the button for

repeat controls in IPOD and Bluetooth modes.

4. Play/Pause Button (

):

Radio or Auxiliary Mode: Press to mute the

audio.

IPOD or Bluetooth Mode: Press to pause

playback.

5.

Select Button: Press to toggle between: bass,

treble, balance, fader, equalizer, area, loudness

and local/distance settings.

6. Track Buttons:
Radio Mode: Press for automatic seek up or

seek down of radio stations. Press and hold
to activate manual tuning.

IPOD or Bluetooth Mode: Press to select the

next or previous tracks.

7. Volume: Press to increase or decrease the

volume level

.

8. Door Release Handle: Lift up on the door

handle to open the door.

9.

Display Area: This area displays mode infor-

mation, in the radio mode the radio frequency
and in IPOD and supported Bluetooth modes
song information is displayed.

10.

3.5mm Jack: Plug a cable into the 3.5mm jack

then into a device (MP3 player or phone) with

a 3.5mm socket. The unit will not control the

device, it simply allows the audio to be played
through the system.

11. Interior Light: When the unit is turned on the

LEDs will automatically illuminate the interior
compartment.

12. Reset/Pair Button (Reset): Press to reset the

microprocessor or pair a wireless remote.

Reset

MODE

RDM

RPTT

SEL

TRACK

VOL

Charge Only

Aux In 1

1

2

3

4

5

6 7

8

MODE

RDM

RPT

SEL

TRACK

VOL

Charge Only

Aux In 1

10 11 13

14 15

9

12

Reset

4

Button Locations and Functions (Continued)

13.

USB Charging Socket: To charge a device plug

the cable into the USB socket then into the device.

Note: The unit will not control the device. The

cable will not transfer audio into the entertain­ment center.

14. Mounting Straps: Holds your device securely

inside the unit.

15. 30-pin Connector for Apple Products: Plug

the 30-pin connector in an IPOD, ITOUCH or

IPHONE. Use the track button to select the
desired song.

Remote Control Button Locations and Functions (Optional)

1.

Display Area: This area displays mode infor-

mation, in the radio mode the radio frequency
is dis

played.

2. Random Button (RDM): Press the button for

random controls in IPOD and Bluetooth mode.

3. Power and Mode Buttons:
Wired Remote Controller’s Power Button:

Press to turn the entertainment center on.
Press and hold the button for 2 seconds to
turn the unit off.

Wireless Remote Controller’s Power Button:

Press to turn on the entertainment center
on. Press again to turn the unit off.

Mode Button: Press to select between input

sources:

Radio: FM tuner.
IPOD: 30-pin connector. (Can be selected

only when a device is connected).
Aux in 1: 3.5mm jack.
Aux in 2: Rear RCA connectors.

Bluetooth: Wireless connectivity.

4.

Repeat Button (RPT):

Press the button for

repeat controls in IPOD and Bluetooth mode.

5.

Select Button: Press to toggle between: bass,

treble, balance, fader, equalizer, area, loudness

and local/distance settings.

6.

Volume: Press to increase or decrease the vol-

ume level.

7. Track Buttons:

Radio Mode: Press for automatic seek up or

down for radio stations. Press and hold to
activate manual tuning.

IPOD or Bluetooth Mode: Press to select the

next or previous tracks.

8. Play/Pause Button (

):

Radio or Auxiliary Modes: Press to mute the

audio. Press again to restore audio.

IPOD or Bluetooth Mode: Press to pause play

back. Press again to resume play.

Note 1: The wireless remote controller’s display

will disappear after approximately 30 seconds of

no button activity to conserve it’s battery. Press

any button on the remote controller and the LCD
display will be restored.

Note 2: When the main unit is turned off, the

wireless remote controller’s display will disappear
to conserve it’s battery. Press any button on the
remote controller to restore the remote’s display.
Then press the

button to turn on the entertain-

ment center.

RPT

SEL

VOL

VOL

MODE

1

2

3

4
5

7

6

8

RDM

Wired Remote Controller

Wireless Remote Controller

RPT

SEL

MODE

VOL

VOL

1

2

3

4

5

6

7

8

RDM

5

General Operations

Power On:

Press the / MODE button to turn the entertain­ment center on.

Power Off:

Press and hold the / MODE button for 2 sec­onds to turn the unit off.

Selecting a Play Source:

Press the MODE button to select between input

sources. The source will appear in the display.

Radio: FM tuner.

IPOD: 30-pin connector. (Can be selected
only when a device is connected).

Aux in 1: 3.5mm jack.
Aux in 2: Rear RCA connectors.
Bluetooth: Wireless connectivity.

Sound Controls

Volume:

Increase the volume by pressing the VOL
button. Decrease the volume by pressing the
VOL button.

MODE

RDM

RPT

SEL

TRACK

VOL

Charge Only

Aux In 1

MODE

SEL

TRACK

VOL

Charge Only

Aux In 1

Display

MODE

SEL

TRACK

VOL

Charge Only

Aux In 1

Increase

Decreas

e

RDM

RPT

RDM

RPT

6

Equalizer (EQ):

Select the Equalizer mode by pressing the SEL
button until “DSP OFF” appears in the display. To
change the equalizer setting press the

VOL

but-

ton. Select between: Flat, Pop, Jazz, Rock, Classic
and Equalizer Off (DSP OFF).

Note: When an Equalizer setting is selected (Flat,
Pop, Jazz, Rock or Classic) both the Bass and
Treble mode will become inactive and can not be
selected. To change the bass and treble settings set
the Equalizer to “DSP OFF”.

Loudness:

Loudness will boost high and low tones at low

volume levels. To turn on Loudness

press the

SEL button until “LOUD OFF” appears in the dis­play. Press the

VOL

button and “LOUD ON”

will appear in the display

. Loudness mode is now

activated.

Sound Controls (Continued)

Bass:

Select the Bass mode by pressing the SEL button
and “BAS 0” will appear in the display. Increase the
Bass by pressing the VOL button. Decrease
the Bass by pressing the VOL button.

Bass, Treble, Balance, Fader and Equalizer Control

Select the desired sound mode by pressing the SEL button. The modes will be displayed in the following
order: Bass, Treble, Balance, Fader, Equalizer, Area Setting, Loudness, Distance/Local and Volume. After

5 seconds of inactivity control reverts back to volume control.

Treble:

Select the Treble mode by pressing the SEL button
until “TRE 0” appears in the display. Increase the
Treble by pressing the

VOL

button. Decrease

the Treble by pressing the

VOL

button.

Balance:

Select the Balance mode by pressing the SEL
button until “BAL L=R” appears in the display.
Adjust the Balance to the right speakers by press­ing the

VOL

button. Adjust the Balance to the

left speakers by pressing the

VOL

button.

R

-

-

L = Equal sound Right and Left.
R 10R = Right speakers only.
L 10L = Left speakers only.

Fader:

Select the Fader mode by pressing the SEL
button until “FAD F=R” appears in the display.
Adjust the Fader to the front speakers by press­ing the

VOL

button. Adjust the Fader to the

Rear speakers by pressing the

VOL

button.

F

-

-

R = Equal sound Front and Rear.
F 10F = Front speakers only.
R 10R = Rear speakers only.

MODE

RDM

RPT

SEL

TRACK

VOL

Charge Only

Aux In 1

Adjustment

Buttons

MODE

SEL

TRACK

VOL

Charge Only

Aux In 1

Display

RDM

RPT

7

Sound Controls (Continued)

Mute:

Press the

button to mute the volume level.

Press the button again to restore the volume.
Note: If the unit is in either the IPOD or Bluetooth

mode pressing the button will pause play­back. Press the button again will resume
playback.

Using an IPHONE or IPOD

Inserting an IPHONE or IPOD into Docking
Station:

1. Open the waterproof door.

2. Remove the 30-pin connector from its

recessed area.

3.

Plug the 30-pin connector into the Apple device.

4.

Secure the Apple device with the mounting straps.

5.

Close the waterproof door

.

Note 1: If your Apple device uses a lightning
connector a lightning adapter will plug into the
30-pin connector and will allow you to operate
the device normally.

Note 2: If you use the USB cable that came with
your Apple device and plug it into the Charge

Only socket it will only charge the Apple device.

Operating an IPHONE or IPOD:

Selecting the IPOD Mode:

Press the MODE button until “IPOD” appears in
the display.

Note 1: The unit will automatically switch to the

“IPOD” mode when the IPHONE or IPOD is ini­tially connected to the 30-pin connector.

Note 2: The display will show Track/Elapsed
Time, Title, Artist and Album.

MODE

SEL

TRACK

VOL

Charge Only

Aux In 1

RDM

RPT

MODE

SEL

Charge Only

Aux In 1

30-Pin

Connector

MODE

SEL

TRACK

VOL

Charge Only

Aux In 1

RDM

RPT

RDM

RPT

8

Using an IPHONE or IPOD

Changing the Track:

Press the

TRACK button to select a higher

track. Press the

TRACK button to select a

lower track.

Random Play Selection:

The default setting is the Random feature is off.

Random Track Selection:

To randomly play tracks press the RDM button
until “RDM TRK” appears in the display. The

tracks will now play in a random order.

Random Album Selection:

To randomly play albums press the RDM button
until “RDM TRK” appears in the display. Press

the RDM button again until “RDM ABM” appears
in the display. The albums will now play in ran­dom order.

Cancelling Random Play:

To cancel random play keep pressing the RDM
button until “RDM OFF” appears in the display.

Repeat Play Selection:

The default setting is the Repeat feature is off.

Repeat Track Selection:

To repeatedly play a track press the RPT but-
ton until “RPT ONE” appears in the display.
The track will play repeatedly.

Repeat Album Selection:

To repeatedly play all tracks press the RPT
button until “RPT ONE” appears in the display.

Press the RPT button again until “RPT ALL”
appears in the display. All the tracks will play
repeatedly.

Cancelling Repeat Play:

To cancel repeat play keep pressing the RPT
button until “RPT OFF” appears in the display.

IPOD

MODE

SEL

TRACK

VOL

Charge Only

Aux In 1

Track

Number

Elapse

Time

MODE

SEL

TRACK

VOL

Charge Only

Aux In 1

IPOD

RDM

MODE

SEL

TRACK

VOL

Charge Only

Aux In 1

IPOD
RPT

RDM

RPT

RDM

RPT

RDM

RPT

9

Using an IPHONE or IPOD

Lingo Modes:

Lingo Mode 4 (default): Devices with iOS 6.1 software

or higher the touch screen for music is active. Devices
with non-iOS or older versions of iOS software, the
touch screen for music is inactive. In lingo mode 4

song information will be shown in the LCD display.
Lingo Mode 2: Devices with non-iOS or older versions

of iOS software the touch screen is active. In lingo
mode 2 song information will not be display. Only
play, pause and track buttons are active.

Changing the Lingo Mode:

1. Press and hold the SEL button until “LINGO

4” appears in the display.

2. Press the VOL

button and “LINGO 2”

appears in the display.

3.

Press the SEL button to confirm your selec-

tion. The non-iOS software device can now be

directly accessed.

Using a Device with 3.5mm Audio Output

Inserting a Device with 3.5mm Audio Output
Jack into Docking Station:

1. Open the waterproof door.

2. Plug a 3.5mm cable (not supplied) into the

docking station and then into the device.

3.

Plug a USB cable (not supplied) into the dock­ing station and then into the device.

4.

Secure the device with the mounting straps

.

5.

Close the waterproof door

.

Note 1: The USB cable does not have to be

connected for proper operation. Connecting the
USB cable will only charge the device. No data
transfer will occur.
Note 2: If cables are not being used remove the
cable from the waterproof compartment.

Selecting the Input Mode:

1. Press the MODE button until “AUX IN1”

appears in the display.

2. Use the controls on the entertainment center

to adjust the volume.

Note 1: The unit will not automatically switch
to “AUX IN1” mode when the device is initially
connected to the 3.5mm cable. Select “AUX IN1”

using the MODE button.

Note 2: The entertainment center will not control

the device it just allows for the audio from the
device to play through the entertainment center.

Note 3: For optimum sound quality make sure the
media volume on the device is set at 75% or greater.

MODE

SEL

TRACK

VOL

Charge Only

Aux In 1

IPOD

RDM

RPT

MODE

SEL

TRACK

VOL

Charge Only

Aux In 1

Charge Only

Aux In 1

RDM

RPT

MODE

SEL

Charge Only

Aux In 1

USB

Cable

3.5mm
Cable

RDM

RPT

10

Bluetooth Operation

Pairing Bluetooth Devices:

1. Open the Bluetooth setup program on the mobile

device and activate the Bluetooth feature.

2.

Press the button to turn on the entertainment center.

3. From you mobile device scan for available devices.

Select ”AQUAVIBE” to connect to the unit.

4.

When the mobile device has been paired “ ”

will

appear in the entertainment center’s display

.

5.

Press the MODE button until “BT AUDIO” appears in
the display. Bluetooth audio from your mobile device
can now be played through the entertainment center.

Note 1: A previously paired Bluetooth mobile device
will automatically connect to the entertainment center

when “BT AUDIO” is selected using the

MODE button

(if it is within range).
Note 2: If the Bluetooth mobile device is already

paired with the entertainment center, select

“AQUAVIBE” on your phone and touch “Connect”.

Bluetooth Operation:

Note: Devices with AVRCP 1.3 or above will display text,

all other device will simply show “BT AUDIO”

Play/Pause Button:

Press the button to pause the

Bluetooth playback. Press again to resume playback.

Note: The Entertainment Center display will not
show the playback is pause. The mobile device will

show that the playback is paused.

Changing the Track:

Press the

TRACK button to select a higher track.

Press the

TRACK button to select a lower track.

Sound Controls: Use the sound controls on the main

unit to adjust the volume and sound quality.
Note: For optimum sound quality make sure the

media volume on the device is set at 75% or greater.

Random Controls:

Press the RDM button for random

controls. Selecting “RDM ON” will randomly play
tracks. Selecting “RDM OFF” will cancel random play.

Repeat Controls:

Press the RPT button for repeat

controls. Selecting “RPT ONE” will repeatedly play a
track. Selecting “RPT ALL” will repeatedly play all the
tracks. Selecting “RPT OFF” will cancel repeat play.

External Rear Audio Input

Selecting the Input Mode:

1. Press the MODE button until “AUX IN2” appears in
the display.

2. Use the controls on the entertainment center to

adjust the volume.

Note 1: The entertainment center will not control the

device it just allows for the audio from the device to
play through the entertainment center.

Note 2: For optimum sound quality make sure the
media volume on the device is set at 75% or greater.

Note: During Bluetooth audio streaming the
multi-media device (IPHONE/smart phone)
can be placed in the dock and charged by
the USB socket.

MODE

SEL

TRACK

VOL

Charge Only

Aux In 1

RDM

RPT

MODE

SEL

TRACK

VOL

Charge Only

Aux In 1

MODE

SEL

TRACK

VOL

Charge Only

Aux In 1

Display

11

Radio Operations

Manually Tuning in a Radio Station:

Press and hold the TRACK button until
“MANUAL” appears in the display. Then press
the TRACK button to manually tune to a
higher radio station or press the TRACK
button to manually tune to a lower radio station.

Note: After 5 seconds of inactivity control reverts

back to scan tuning. “AUTO” will be displayed in

the LCD.

Tuning in a Radio Station Using Seek:

Press the TRACK button and the tuner will
seek up to the next strong station and stop seek­ing, then start playing.

Press the TRACK button and the tuner will
seek down to the next strong station and stop
seeking, then start playing.

Selecting the FM Radio Mode:

Press the MODE button until “RADIO” appears in
the display. After a brief moment “FM” will appear
in the display along with the radio frequency.

MODE

SEL

TRACK

VOL

Charge Only

Aux In 1

MODE

SEL

TRACK

VOL

Charge Only

Aux In 1

Higher

Lower

MODE

SEL

TRACK

VOL

Charge Only

Aux In 1

Hold

RDM

RPT

RDM

RPT

RDM

RPT

12

Radio Operation (Continued)

Distance/Local Reception Operation:

When scanning for station to eliminate weaker
fringe stations change the radio reception from
Distance (DX) to Local (LOCAL).

1.

To switch from distance to local reception press

the SEL button until “DX” appears in the display.

2. Press the VOL button and

“LOCAL” will

appear in the display.

Note: The unit will leave feature programing after

5 seconds of no button activity.

Stereo/Mono Operation:

Note: “ST” will appear in the display when a FM

stereo station is being received.

For weaker FM stereo stations selecting mono
reception usually improves reception.

1.

To switch from stereo to mono reception press

the SEL button until “STEREO” appears in the
display.

2. Press the VOL button and

“MONO” will

appear in the display.

Note: The unit will leave feature programing after

5 seconds of no button activity.

Switching from US to Europe Radio Tuning

Note: Do not change if using in North America.

1. Press the SEL button until “AREA USA”

appears in the display.

2. Press the VOL button and

“AREA EUR”

will appear in the display.

Note: The unit will leave feature programing after

5 seconds of no button activity.

RDM

RPT

RDM

RPT

MODE

SEL

TRACK

VOL

Charge Only

Aux In 1

ST

Stereo

Reception

Indicator

MODE

EN

SEL

TRACK

VOL

Charge Only

Aux In 1

MODE

EN

SEL

TRACK

VOL

Charge Only

Aux In 1

RDM

RPT

13

Reset

Resetting the System:

To reset the microprocessor to the original

factory settings use a ball point pen and press
the RESET button located in the interior of the
waterproof compartment.

Inserting a Battery into Remote Controller

Inserting a Battery:

1.

Use a coin to unlock the battery cover.

2. Insert the battery with the + side of the battery
facing up.

3. Replace the battery cover and use a coin to
lock the battery cover making sure it locks
into place.

Note: When the text in the LCD is dim, replace
the battery.

Programming a Wireless Remote Controller

Programming a Wireless Remote Controller:

1. To pair the wireless remote with the dock

push and hold the MODE button on the

remote controller until “PAIR” appears in it’s

display

2. While still holding the MODE button on the
wireless remote controller, press the RESET

button in the interior of the waterproof com­partment to pair the devices.

3. If the pairing is successful, the dock will
restart and “PAIR” will disappear from the
remote’s display. Release the MODE button
on the remote controller

.

Lock

Coin

Battery +
Side Up

MODE

SEL

TRACK

VOL

Charge Only

Aux In 1

RDM

RPT

Reset

MODE

SEL

TRACK

VOL

Charge Only

Aux In 1

RPT

SEL

RDM

MODE

VOL

VOL

Hold

RDM

RPT

Reset

14

Installation

Installing Entertainment Center

1. Use the template included to determine the best
location for the entertainment center.

Note: The mounting location needs to be a flat

surface.

2. Cut out the mounting hole and drill pilot holes
for the screws.

3. Mount the entertainment center using the pro­vided screws. Make sure to tighten the screws
equally to create a waterproof seal.
Note: If the surface is uneven like wood, use
silicone to create a waterproof seal between the
uneven surface and the entertainment center.

4. Install the screw covers.

Supplied

Mounting

Screws

Supplied

Screw

Covers

Use Supplied Template to Cut Hole

and Make Pilot Holes for Screws

Installing Wired Remote (Optional)

1. Install mounting studs into rear of remote con­troller. Hand tighten the studs only.

2. Cut a 2-1/8” hole.

3. Insert cable from remote controller through the
hole and then mounting bracket.

4. Slide mounting bracket onto mounting studs.

5. Screw the wing nuts onto the studs and hand
tighten them against the mounting bracket. Do
not use pliers to tighten the wing nuts.
Note: If the surface is uneven like wood, use
silicone to create a waterproof seal between the
uneven surface and the remote control.

Mounting

Studs

Wing

Nuts

Mounting

Bracket

Cable

15

Wiring

External Automotive

Type Antenna

(Optional)

White/Black Wire

Left

Front

Speaker

White Wire

Gray/Black Wire

Gray Wire

Right
Front

Speaker

Right

Rear

Speaker

Violet/Black Wire

Violet Wire

Green/Black Wire

Green Wire

Left

Rear

S

peaker

Blue Wire Trigger for Amp (+12VDC)

Black Wire Ground

Red Wire (+) to 12 Volt Ignition

10 Amp

Fuse

ENT

SEL

MENU

VOL

VOL

MODE

Wired Remote

(Optional)

Black Wires Audio In (Aux in 2)

Gray Wires Audio Out

Right

Left

Right

Left

Wiring Harness

Model: SPA-HAR

(Sold Separately)

© Copyright 2013
Magnadyne Corporation

MD-X50-UM

Rev. A 5-15-13

Warranty

ONE (1) YEAR LIMITED WARRANTY

Magnadyne Corporation or its authorized agents will within one year from the date of sale

to you, repair, replace or refund the retail sales price of said product or any part thereof, at

the option of the Magnadyne Corporation or its authorized agents, if said product or part

is found defective in materials or workmanship, when properly connected and operating

on the correct power requirements designated for the specific product. This warranty and
Magnadyne Corporation or its authorized agent’s obligations hereunder do not apply where

the product was; damaged while in the possession of the consumer, subjected to unrea-

sonable or unintended use, not reasonably maintained, utilized in commercial or industrial
operations, or serviced by anyone other than Magnadyne Corporation or its authorized

agents, or where the warning seal on the product is broken or the power and/or plugs

are detached from the unit. Magnadyne Corporation or any of its authorized agents will

not assume any labor costs for the removal and reinstallation of any product found to be

defective, or the cost of transportation to Magnadyne Corporation or its authorized agents.

Such cost are the sole responsibility of the purchaser.
This warranty does not cover the cabinet appearance items or accessories used in con­nection with this product, or any damage to recording or recording tape, or any damage
to the products resulting from improper installation, alteration, accident, misuse, abuse or
acts of nature.

MAGNADYNE CORPORATION OR ITS AUTHORIZED AGENTS SHALL NOT BE LIABLE TO
ANYONE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES OR CLAIMS EXCEPT THOSE
ACCORDED BY LAW. NO EXPRESSED WARRANTY OR IMPLIED WARRANTY IS GIVEN
EXCEPT THOSE SET FORTH HEREIN. NO IMPLIED WARRANTY SHALL EXTEND BEYOND
ONE YEAR FROM THE DATE OF SALE.
This warranty extends only to the original purchaser of the product and is not

transferable. Some states do not allow limitations on how long an implied warranty lasts,
and some states do not allow the exclusion or limitation of incidental or consequential

damages, so the above limitations or exclusion may not apply to you. This warranty gives

you specific legal rights, and you may have other rights that vary from state to state.

“NOTE: The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the User’s
authority to operate the equipment.”

Defective merchandise should be returned to the original point of purchase or
secondly, to Magnadyne Corporation, 1111 W. Victoria Street, Compton CA 90220.

Return Authorization must be obtained before sending, or merchandise may be refused.

FCC Statement:

This device complies with part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) This device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired

operation.

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following

measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications not expressly approved by the party responsible

for compliance could void the user's authority to operate the equipment.