Magnadyne 4900, 4960 User Manual
OWNER’S
MANUAL
Models: 4900 Series
4960 Series
Vehicle Immobilizers
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference; and
(2) This device must accept any interference received, including interference that may cause undesired operation.
Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to
this equipment. Such modifications could void the user’s authority to operate the equipment.
Silencer products have been designed to provide the consumer with years of trouble-free operation.
Disarm
Valet
On
Valet
Off
This manual will provide reference for the operation and maintenance of your new Silencer vehicle
immobilizer system. Please, take a moment to read this manual so you will be familiar with the operation of your new system.
3-Button Transmitter
1-Button Transmitter
1-Button Automatic
Disarm Transmitter
Note: Depending on the type of consumer transmitter package your dealer provided you with, you
may have each one of the transmitters pictured above, or two of the same type transmitter.
Confirm this with your dealer.
Automatic Arming
Once you have turned the ignition key to the “Off” position, your Silencer engine immobilizer will
become armed within 30 seconds. Upon arming, the device will emit 1 soft chirp. Turning the ignition back on before 30 seconds will stop the timer and reset it.
Note: If your system was supplied with an “Automatic Disarm Transmitter”, you will need to leave
the vicinity of your vehicle (approx. 60 feet) before the automatic arming function will execute.
(Remaining in close proximity of your vehicle could prevent it from arming). The distance requirement may prevent you from hearing the soft arming chirp.
Manual Disarming
3-Button Transmitter:
When you return to your vehicle to start the engine, press the “Disarm” button on the 3-button transmitter. When the system is disarmed, the device will emit 2 chirps indicating it’s disarmed.
1-Button Transmitter: When you return to your vehicle to start the engine, press the transmitter but-
ton. When the system is disarmed, the device will emit 2 chirps indicating it’s disarmed.
Automatic Disarming (Automatic Disarm Transmitter Required)
1-Button Automatic Disarm Transmitter: When you return to your vehicle, at some point, between
a distance of approx. 60 feet and the time you insert your ignition key to start the engine, the automatic disarm transmitter will disarm your system. Once disarmed, the device will emit 2 soft
chirps. No action is required by the operator.
Note: In areas of high radio frequency noise, the automatic disarm function of the transmitter may
get blocked and not disarm your system. In this event, press the transmitter button to perform a
manual disarm.
2
Radio Frequency (RF) Protection Rearm Timer
Each time the system is disarmed using the transmitter the device will begin a protection mode
countdown. This is a timed secondary protection mode. If you do not start your vehicle within 60
seconds, your Silencer system will become rearmed and your engine will become disabled again.
Note: If your system operates from a “Automatic Disarm Transmitter”, the 60 second RF protection
timer will not time-out and will rearm your system if you remain within 60 feet of your vehicle.
Automatic/Manual Disarm Transmitter Programming
If your transmitter package contains one or more of the 1-button automatic disarm transmitters, the
default operating mode will be “Manual Mode” (to preserve the battery life while not in use). To
change the operating mode to “Automatic Mode”, follow these steps:
1. Press the middle area of the button and hold it down until the LED light on the side of the button becomes solid red. Release the button.
2. Press and release the center of the button 3 times. You will notice that the red LED light will be
off.
3. Press and hold the center of the button until the LED flashes. Release the button.
3 flashes = The transmitter is in “Automatic Disarm” mode.
1 flash = The transmitter is in “Manual Disarm” mode.
4. Confirm the mode of the transmitter. Press and release the center of the button and watch the
flash sequence of the LED.
5. The transmitter operating mode can be changed at any time by following steps 1-3. Confirm
the mode by following step 4.
3
Loading...