Mag Mara Technologies X01 User Manual

MYDAIGO OPERATING INSTRUCTIONS

(Completely read instructions and the terms and conditions prior to use)

TRANSMITTER (TX) -Peel tape and attach to your item OR Peel tape

and attach to plastic backplate (included) and hang from your item.

Turning (TX) Power On – Quickly press and release button.

Notes/Tips
If not paired, it will flash slowly 5 times and return to off state.
If paired, it will start transmitting as scheduled and blink every 5 seconds
(after 1 minute, only every second signal will blink to reduce power
consumption).
When ON in low power consumption mode, any short button press will
activate the LED for quick user feedback.

Turning (TX) Pairing Mode On – From OFF state ONLY, press and

hold the button for 3 seconds to enter pairing mode.
Notes/Tips
LED will begin short flashes on the 3 seconds mark, so release the
button.
LED will continue flashing once every second while in pairing mode.
Place RX in pairing mode within this interval to allow the two to pair.
Pairing state will terminate after 60 seconds if pairing was unsuccessful
and the TX will turn OFF.
Turning (TX) Power Off – Press and hold button for 3 seconds until
LED flashes rapidly 3 times then within 1.5 seconds press the button
again quickly to turn off.
Notes/Tips
If turn off sequence has completed successfully, 3 rapid flashes will
occur before TX turns OFF.
If not successful, the TX continues to transmit as scheduled and LED
flash every 5 seconds.

RECEIVER (RX)
Turning (RX) Power ON – Press and hold (power/bottom) button for 3

sec to power up receiver.
Notes/Tips
LED will light up (left-to-right) when RX turns on.

To minimize power consumption, you should have TX already turned on.
If there is no paired TX to transmit, the RX will auto-shutoff in 6 seconds
to save power.
Turning (RX) Power Off – Press and hold for 3 seconds both the
(power/bottom) button and the (range/middle) button to power down.
Notes/Tips
Entering the power OFF state is signaled with LED lighting (right-to-left).

PAIRING TX & RX

To minimize RX power consumption, place TX in pairing mode first (see
TX operation above).
Turning RX Pairing Mode On – From powered OFF state ONLY, press
and hold the (power/bottom) button & (time delay/top) button
simultaneously until the left & right LEDs turn on after (approximately 3
seconds).
Notes/Tips
If unsuccessful, RX will auto-shutoff after 20 seconds.
If TX is detected and received correctly, the LED on the right will flash
shortly.
Both RX and TX will resume normal ON modes with the LEDs flashing
in sync every 5
selected will flash on RX.
After 1 minute the flashing will stop to save battery power. At anytime
you can quickly press and release the button to begin the 1 minute
flashing cycle again and confirm that the power is on and the RX and TX
are still communicating correctly.

OTHER FUNCTIONS

Selecting Alarm signal type/sound:

From powered off state only, press and release the (power/bottom)
button on RX to cycle through the alerting options: (1 long beep, 3 short
beeps, 5 short beeps)
RX will sound the buzzer on button release, according to the current
setting. RX remains in OFF state.

Change alerting range (allowable distance set):

From On state only, press and hold (range/middle) button for 2 seconds
until current range LED starts flashing rapidly.

seconds

. The LED corresponding to the current range

While in range adjust mode, quickly press and release the same
range/middle button to cycle through the ranges available
(short/medium/long).
Once desired distance is chosen, press and hold the range/middle
button for 2 seconds (LED will stop flashing) and activate range is now
selected.

Select and activate mute delay (Temporary muting of alarm):

Once the time delay is set, it can only be turn off by powering the RX off
and on or letting the time selected expire.
From On state only, press and hold (time delay/top) button for 2
seconds to enter delay selection and activation.
Current delay setting LED will start flashing rapidly. Time delay choices
from left to right are 15 minutes, 30 minutes, and 1,3 or 5 hours.
Press (delay/top) button repeatedly to select desired time delay.
Press and hold for 2 seconds delay button to select displayed delay
and activate the delay timer.
If delay is activated, pressing delay/top button will display current delay
LED in progress.
If delay is not activated, the button is inactive and no LED feedback
occurs.

Alarm features:

If connection communication between the TX & RX is lost, the alarm
will signal for 30 seconds followed by a 2 second long beep signaling
that the RX goes to a silent period of 60 seconds.
At anytime during the 30 seconds communication between the two is
re-established, the alarm signal will stop and the LED will begin to blink
simultaneously again.
However, if after 30 seconds the communication between the TX & RX
is still lost, it will sound the alarm once, followed by a 2 second long
beep and the cycle repeats until TX comes back within range or user
powers down the RX.
If you intentionally leave your item behind and the alarm is sounded,
the mute function is available but it is recommended that you power the
receiver off to save battery life.

Please completely read the following terms and conditions

prior to use of MyDaigo.

DISCLAIMER OF WARRANTIES; LIMITATION OF LIABILITY By

reading the terms and agreement you are aware and agree that you are
using MyDaigo at your own risk and that the accuracy and results of
your MyDaigo product may vary. If you have any questions or concerns
about the product or any of the following terms and conditions, you are
advised to contact MyDaigo Inc via email at [e-mail] or by
calling 1+[phone] or toll free at 1(855)993-2446 prior to use of
any MyDaigo products. You agree and acknowledge that the use of
MyDaigo relies on radio frequency communication between a
transmitter and a receiver and depending on the surroundings, the
results may vary. We do not guarantee, represent or warrant that your
use of our product will be uninterrupted, timely, secure or error-free. We
do not warrant that the results that may be obtained from the use of the
MyDaigo product will be accurate or reliable. You expressly agree that
your use of, or inability to use, the product is at your sole risk. The
service and all products and services delivered to you through use of
our products are (except as expressly stated by us) provided 'as is' and
'as available' for your use, without any representation, warranties or
conditions of any kind, either express or implied, including all implied
warranties or conditions of merchantability, merchantable quality, fitness
for a particular purpose, durability, title, and non-infringement. In no
case shall MyDaigo Inc, our directors, officers, employees, affiliates,
agents, contractors, interns, suppliers, service providers or licensors be
liable for any injury, loss, claim, or any direct, indirect, incidental,
punitive, special, or consequential damages of any kind, including,
without limitation lost profits, lost revenue, lost savings, loss of property,
loss of data, replacement costs, or any similar damages, whether based
in contract, tort (including negligence), strict liability or otherwise, arising
from your use of any of our products, or for any other claim related in
any way to your use of the service or any product, including, but not
limited to, any errors or omissions in any content, or any loss or damage
of any kind incurred as a result of the use of MyDaigo (our product).

Because some states or jurisdictions do not allow the exclusion or the
limitation of liability for consequential or incidental damages, in such
states or jurisdictions, our liability shall be limited to the maximum extent
permitted by law. INDEMNIFICATION You agree to indemnify, defend
and hold harmless MyDaigo Inc and our parent, subsidiaries, affiliates,
partners, officers, directors, agents, contractors, licensors, service
providers, subcontractors, suppliers, interns and employees, harmless
from any claim or demand, including reasonable attorneys’ fees, made
by any third-party due to or arising out of your breach of these Terms of
Service or the documents they incorporate by reference, or your
violation of any law or the rights of a third-party. GOVERNING LAW
These Terms of Service and any separate agreements whereby we
provide you Services shall be governed by and construed in accordance
with the laws of the Province of Ontario Canada. CHANGES TO
TERMS OF SERVICE You can review the most current version of the
Terms of Service at any time at www.mydaigo.com. We reserve the
right, at our sole discretion, to update, change or replace any part of
these Terms of Service by posting updates and changes to our website.
It is your responsibility to check our website periodically for changes.
Your continued use of or access to our website or the Service following
the posting of any changes to these Terms of Service constitutes
acceptance of those changes.

REFUND POLICY
RETURNS All refunds must be made within 30 days of the purchase

date. Any item not in its original condition is damaged or missing parts
for reasons not due to our error will not be refunded or exchanged. Nor
are we responsible for refund or exchange on any item that is returned
more than 30 days after delivery. To complete your return, we require a
receipt or proof of purchase. Please email us at info@mydaigo. com or
call us toll free at 1(855) 993-2446 prior to returning. REFUNDS (if
applicable) once your return is received and inspected, we will send you
an email to notify you that we have received your returned item. Please
include a valid email to receive this notification. We will also notify you of
the approval or rejection of your refund. If you are approved, then your

refund will be processed, and a credit will automatically be applied to

FCC Caution: Any changes or modifications not expressly approved by

your credit card or original method of payment. SALE ITEMS (if

the party responsible for compliance could void the user's authority to

applicable) may be refunded, but will only be refunded at the sales price

operate this equipment.

verified by proof of purchase receipt. EXCHANGES (if applicable) If you
feel your product is defective or damaged, you must first contact our

This device complies with Part 15 of the FCC Rules. Operation is subject

customer service department toll free at 1(855) 993-2446 or via email at

to the following two conditions: (1) This device may not cause harmful

[e-mail] prior to returning. Once our customer service

interference, and (2) this device must accept any interference received,

department has had a chance to reply or contact you, we may then

including interference that may cause undesired operation.

request you to send your item to the offices of MyDaigo Inc. SHIPPING
To return your product, you should mail your product to: MyDaigo Inc.

NOTE: This equipment has been tested and found to comply with the

16 Industrial Parkway South, Suite 312, Aurora, Ontario Canada

limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against

L4G-0R4.You will be responsible for paying for your own shipping costs

harmful interference in a residential installation. This equipment

for returning your item. Shipping costs are non-refundable. If you

generates, uses and can radiate radio frequency energy and, if not

receive a refund, the cost of return shipping will be deducted from your

installed and used in accordance with the instructions, may cause

refund. Depending on where you live, the time it may take for your

harmful interference to radio communications.

exchanged product to reach you, may vary.If you are shipping an item

However, there is no guarantee that interference will not occur in a

over $75, you should consider using a trackable shipping service or

particular installation.

purchasing shipping insurance. We don’t guarantee that we will receive

If this equipment does cause harmful interference to radio or television

your returned item.

reception,which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more

QUESTIONS AND CONTACT INFORMATION

of the following measures:

If you would like to: access, correct, amend or delete any personal

-- Reorient or relocate the receiving antenna.

information we have about you, register a complaint, or simply want

-- Increase the separation between the equipment and receiver.

more information regarding our terms, conditions, or privacy

-- Connect the equipment into an outlet on a circuit different from that to

policy,contact us via email at [e-mail] or by phone toll free at

which the receiver is connected.

1(855)993-2446 or by mail at MyDaigo Inc. 16 Industrial Parkway

-- Consult the dealer or an experienced radio/TV technician for help.

South, Suite 312, Aurora Ontario, Canada L4G-0R4.