SCOPE
：
This specification applies to the current type Radial Leaded Inductor
(1) SHAPES AND DIMENSIONS
(2) ELECTRICAL SPECIFICATIONS
(3) CHARACTERISTICS
for MCD-1415-SERIES
PRODUCT INDENTIFICATION
MCD- 1415 - 102 K
① ② ③ ④
① Product Code
② Dimensions Code
③ Inductance Code
④ Tolerance Code
A: 16.5 Max. mm
B: 15.5 Max. mm
C: 15.0±2.0 mm
D: 7.5±0.5 mm
E: φ1.0±0.1 mm
F: 3.0 Max. mm
SEE TABLE 1
TEST INSTRUMENTS
L : HP 4284A PRECISION LCR METER (or equivalent)
RDC : CHROMA MODEL 16502 MILLIOHMMETER (or equivalent)
(3)-1 Ambient temperature ……......... ＋60℃ Max.
(3)-2 Operate temperature range ...... －40℃～＋125℃
(Including self temp. rise)
(3)-3 Storage temperature range ...... －40℃～＋125℃
MAG.LAYERS
MCD-1415-SERIES Page 1/4
TABLE 1
MAGLAYERS
Inductance Percent Test Resistance Rated DC Current
PT/NO.
MCD-1415-100□
MCD-1415-120□
MCD-1415-150□
MCD-1415-220□
MCD-1415-270□
MCD-1415-330□
MCD-1415-390□
MCD-1415-470□
MCD-1415-560□
MCD-1415-680□
MCD-1415-820□
MCD-1415-101□
MCD-1415-121□
MCD-1415-151□
MCD-1415-181□
MCD-1415-221□
MCD-1415-271□
MCD-1415-331□
MCD-1415-391□
MCD-1415-471□
MCD-1415-561□
MCD-1415-681□
MCD-1415-821□
MCD-1415-102□
L(μH) Tolerance Frequency RDC(Ω)Max. IDC1(A) IDC2(A)
10 M 100kHz/0.25V 17 m 14.0 6.7
12 K,M 100kHz/0.25V 19 m 12.0 6.6
15 K,M 100kHz/0.25V 21 m 10.0 6.5
22 K,M 100kHz/0.25V 26 m 8.8 5.8
27 K,M 100kHz/0.25V 28 m 8.3 5.3
33 K,M 100kHz/0.25V 34 m 7.8 5.2
39 K,M 100kHz/0.25V 38 m 7.3 5.1
47 K,M 100kHz/0.25V 46 m 6.7 4.6
56 K,M 100kHz/0.25V 51 m 6.2 4.5
68 K,M 100kHz/0.25V 55 m 5.7 4.3
82 K,M 100kHz/0.25V 58 m 5.2 4.2
100 K,M 100kHz/0.25V 75 m 4.6 3.4
120 K,M 100kHz/0.25V 0.100 4.2 3.1
150 K,M 100kHz/0.25V 0.125 3.7 2.9
180 K,M 100kHz/0.25V 0.141 3.5 2.7
220 K,M 100kHz/0.25V 0.208 3.0 2.4
270 K,M 100kHz/0.25V 0.240 2.7 2.3
330 K,M
390 K,M 100kHz/0.25V 0.303 2.3 2.0
470 K,M 100kHz/0.25V 0.342 2.1 1.9
560 K,M 100kHz/0.25V 0.531 1.8 1.6
680 K,M 100kHz/0.25V 0.590 1.7 1.5
820 K,M 100kHz/0.25V 0.728 1.5 1.3
1000 J,K,M 100kHz/0.25V 0.750 1.4 1.2
100kHz/0.25V
0.272 2.5 2.1
※ 1. □ specify the inductance tolerance,J(±5%)K(±10%),M(±20%)
※ 2. IDC1： Based on inductance change (△L/L0 : drop10% Max.) @ ambient temp. 25℃
IDC2： Based on temperature rise (△T：40℃ TYP.)
Rated DC Current： The less value which is IDC1 or IDC2.
MAG.LAYERS
MCD-1415-SERIES
Page-2/4
(4) RELIABILITY TEST METHOD
MECHANICAL
NO. ITEMS
1 Solderability test
2 lead tensile 1.0 Kg MIN. The lead of product is pulled with a load of
strength test 1.0kg mininum until lead breakdown. The tensile
SPECIFICATIONS
More than 90% of the
termnial electrode
should be covered
with solder.
CONDITIONS
Dipping: 245 ± 5 ℃ , 3 ± 1 seconds
force shall be recorded.
3 Vibration test
4 Soldering heat Visual:OK The leads of product are dipped into a solder pot
resistance test Circuit:OK
ENVIRONMENTAL
NO. ITEMS
1 Humidity
endurance
test
2 High temp
endurance test
△L/L≦±7%
Visual:OK
SPECIFICATIONS CONDITIONS
△L/L≦±5% The product is placed in a chamber of 40±2℃,
△L/L≦±5%
The product is fixed ento the vibration with
amplitude of 1.52m/m at a frequency of 10～55Hz
sweeping for lmin. The vibration is done at X,Y,
Z direction respectively for 2 houes, totally 6
hours.
of 260±5℃ for a duration of 10±1sec. Nothing
particular on visual and open circuitry as a
result of ore testing.
90～95%RH for 96 hours. Measurement is done
after the reaovery of 4～24 hours.
The product is placed in a chamber of 80±2℃,
for 72 hours. Measurement is done after recovery
of 4～24 hours.
3 Low temp test
4 Thermal shock
test
MAG.LAYERS
△L/L≦±5%
△L/L≦±5%
The product is placed in a chamber of -40±2℃,
for 96 hours. Measurement is done after
recovery of 4～24 hours.
The specimens are placed in a chamber and the
temp is then lowered to -20±2℃ for one hour.
The temp will raised to +80±2℃ for one hour.
This constitues one cycle. Ten cycles of such
testing shall be completed. Measurement is made
after recovery for 4～24 hours from the
completion of testing.
MCD-1415-SERIES
Page-3/4
(5) PACKAGE SPECIFICATION (mm)
MAG.LAYERS
MCD-1415-SERIES
Page-4/4
Loading...