Mag Layers MCD-0810 User Manual

SCOPE

：

This specification applies to the current type Radial Leaded Inductor

(1) SHAPES AND DIMENSIONS

(2) ELECTRICAL SPECIFICATIONS

SEE TABLE 1

(3) CHARACTERISTICS

for MCD-0810-SERIES

PRODUCT INDENTIFICATION
MCD - 0810 - 102 K

① ② ③ ④

① Product Code
② Dimensions Code
③ Inductance Code
④ Tolerance Code

A: 10.5 Max. mm
B: 10.5 Max. mm
C: 15.0±2.0 mm
D: 5.0±0.5 mm
E: φ0.65±0.1 mm
F: 2.5 Max. mm

TEST INSTRUMENTS
L : HP 4284A PRECISION LCR METER (or equivalent)
RDC : CHROMA MODEL 16502 MILLIOHMMETER (or equivalent)

(3)-1 Ambient temperature ……......... ＋60℃ Max.

(3)-2 Operate temperature range ...... －40℃～＋125℃

(Including self temp. rise)

(3)-3 Storage temperature range ...... －40℃～＋125℃

MAG.LAYERS

MCD-0810-SERIES Page 1/4

TABLE 1

MAGLAYERS

PT/NO.
MCD-0810-1R2□
MCD-0810-2R2□
MCD-0810-3R3□
MCD-0810-4R7□
MCD-0810-6R8□

MCD-0810-100□
MCD-0810-150□
MCD-0810-180□
MCD-0810-220□
MCD-0810-270□
MCD-0810-330□
MCD-0810-101□
MCD-0810-181□
MCD-0810-221□
MCD-0810-271□
MCD-0810-331□
MCD-0810-391□
MCD-0810-471□
MCD-0810-561□
MCD-0810-681□
MCD-0810-821□
MCD-0810-102□
MCD-0810-112□
MCD-0810-122□
MCD-0810-152□
MCD-0810-222□

Inductance Percent Test Resistance Rated DC Current

L(μH) Tolerance Frequency RDC(Ω)Max. IDC1(A) IDC2(A)

1.2 M

2.2 M

3.3 M

4.7 M

6.8 M
10 K,M
15 K,M
18 L,M
22 K,M
27 K,M
33 K,M

100 K,M
180 K,M
220 K
270 K,M
330 K,M
390 K,M
470 K,M
560 K,M
680 K,M

820 K,M
1000 K 100kHz/0.25V 2.30 0.45 0.45
1100 K 100kHz/0.25V 2.60 0.43 0.43
1200 K
1500 K,M
2200 K

100kHz/0.25V
100kHz/0.25V
100kHz/0.25V
100kHz/0.25V
100kHz/0.25V
100kHz/0.25V
100kHz/0.25V
100kHz/0.25V
100kHz/0.25V
100kHz/0.25V
100kHz/0.25V
100kHz/0.25V
100kHz/0.25V
100kHz/0.25V
100kHz/0.25V
100kHz/0.25V
100kHz/0.25V
100kHz/0.25V
100kHz/0.25V
100kHz/0.25V
100kHz/0.25V

100kHz/0.25V
100kHz/0.25V

1kHz/0.25V

7.70m 15.0 8.00

14.0m 12.0 7.00

16.0m 10.0 6.00

18.0m 8.00 5.30

25.0m 5.20 5.00

26.0m 5.00 4.50

68.0m 4.30 2.70

70.0m 4.10 2.70

74.0m 3.90 2.60

82.5m 3.70 2.50

85.0m 3.50 2.40

0.26 1.40 1.40

0.44 1.00 1.10

0.50 0.90 1.00

0.60 0.83 0.90

0.78 0.78 0.80

0.85 0.70 0.75

1.08 0.63 0.70

1.19 0.60 0.65

1.59 0.55 0.55

1.88 0.50 0.50

3.20 0.40 0.40

3.40 0.30 0.37

3.90 0.27 0.35

※ 1. □ Specify the inductance tolerance, K(±10%),L(±15%), M(±20%)
※ 2. IDC1： Based on inductance change (△L/Lo： drop 10% Max) @ ambient temp. 25℃

IDC2： Based on temperature rise (△T： 40℃ TYP.)
Rated DC Current： The less value which is IDC1 or IDC2.

FLOW SOLDERING

℃

150℃

100℃

MAG.LAYERS

MCD-0810-SERIES

Page-2/4

(4) RELIABILITY TEST METHOD

MECHANICAL

NO. ITEMS

More than 90% of the

1 Solderability test

2 lead tensile 1.0 Kg MIN. The lead of product is pulled with a load of

strength test 1.0kg mininum until lead breakdown. The tensile

termnial electrode
should be covered
with solder.

Dipping: 245 ± 5 ℃, 3 ± 1 seconds

force shall be recorded.

CONDITIONSSPECIFICATIONS

3 Vibration test

4 Soldering heat Visual:OK The leads of product are dipped into a solder pot

resistance test Circuit:OK

△L/L≦±7%
Visual:OK

The product is fixed ento the vibration with
amplitude of 1.52m/m at a frequency of 10～55Hz
sweeping for lmin. The vibration is done at X,Y,
Z direction respectively for 2 houes, totally 6
hours.

of 260±5℃ for a duration of 10±1sec. Nothing
particular on visual and open circuitry as a
result of ore testing.

ENVIRONMENTAL

NO. ITEMS

1 Humidity

endurance
test

2 High temp

endurance test for 72 hours. Measurement is done after recovery

SPECIFICATIONS CONDITIONS

△L/L≦±5% The product is placed in a chamber of 40±2℃,

90～95%RH for 96 hours. Measurement is done
after the reaovery of 4～24 hours.

△L/L≦±5% The product is placed in a chamber of 80±2℃,

of 4～24 hours.

3 Low temp test

4 Thermal shock

test

MAG.LAYERS

△L/L≦±5% The product is placed in a chamber of -40±2℃,

for 96 hours. Measurement is done after
recovery of 4～24 hours.

△L/L≦±5%

The specimens are placed in a chamber and the
temp is then lowered to -20±2℃ for one hour.
The temp will raised to +80±2℃ for one hour.
This constitues one cycle. Ten cycles of such
testing shall be completed. Measurement is made
after recovery for 4～24 hours from the
completion of testing.

MCD-0810-SERIES

Page-3/4

(5) PACKAGE SPECIFICATION (mm)

MAG.LAYERS

MCD-0810-SERIES

Page-4/4