Magikitch'n LPAGA, LPAGA-30, LPG-60, LPAGA-60, LPG-30 Options Installation - Operation

LPAGA/LPG & CG

OUTDOOR GRILL OPTIONS

INSTALLATION - OPERATION

P.O. Box 501, Jct. I-89 & I-93 Concord, NH 03302-0501 • 509 Route 3A, Bow, NH 03304 USA

Telephone [phone] • [phone] • Fax: [phone]

PITCO FRIALATOR INC.

www.PITCO.com

PN L25-007 Rev. 1 (12/01)

© 2001 - Pitco Frialator Incorporated

Table of Contents

1. Hood Handle and Hood Bracket Assembly........................................................................................2

2. Twin Hoods for the LPAGA/LPG-60 .................................................................................................. 3

3. Single Hood for the LPAGA/LPG-30.................................................................................................. 4

4. Single (Full size) Hood for the LPAGA/LPG-60 ................................................................................ 5

5. Full Hood for the CG-60 ...................................................................................................................... 6

6. Steamer Support, Steamer Pan Set and MagiGriddle Options ........................................................ 7

7. The Windguard Option ........................................................................................................................ 8

8. Split Options for the LPAGA/LPG-30 ................................................................................................ 9

9. Cutting Board for the LPAGA/LPG-30 ............................................................................................ 10

10. Cutting Board for the LPAGA/LPG-60 ..........................................................................................11

11. Side Shelf for LPG-30/60 and the LPAGA-30/60 ........................................................................... 12

1. Hood Handle and Hood Bracket Assembly

T

HOOD, BRACKET OUTER LEFT

5402-1187701

CRADLE

SCREW, 1/4-20 x 3/4”, INT. LOCKWASHER

(PART OF 7299-1257300 HDWE KIT)

5602-1190600

HOOD, HANDLE SUPPORT ROD

5602-1190500

HOOD, HANDLE TUBULAR

HOOD, BRACKET OUTER RIGHT

5402-1187702

4001-0963400

HOOD, BRACKET CENTER LEFT/RIGH

5402-1188002, RIGHT

5402-1188001, LEFT

10545C2.DWG

The Handles (top illustration)

Each handle has two support rods and a center tube. To assemble the handles more easily, open each hood up and turn it upside

down on a large table. The ¾” long bolts from the handle hardware kit go in from the inside of the hood and fasten to a
support rod; point the support in the right direction and snug it up finger tight. Place the tubular handle onto the first
support and slip the second support into place. Hold the second support in position and install the other ¾’ long bolt
through the back of the hood and into the threaded hole in the second support and tighten it. Align the tubular handle and
the support rods in a straight line and tighten the mounting bolts securely with a #3 Phillips screwdriver. Repeat this
procedure for each of the handle sets to be installed. It is important to install all the handles for the hood so it can be easily
removed if it is hot.

The Hood Mounting Brackets (bottom illustration)

All single hoods require a pair of outer brackets. Units with twin hoods also require a pair of center brackets. Each type has a

left and right hand mate. All the brackets mount with ¾” long bolts that mate with threaded fasteners built into the frame
of the broiler grills. The instructions and illustrations for every combination of hood option can be found in this manual.

2 L25-007 Rev. 1 12/2001

2. Twin Hoods for the LPAGA/LPG-60

T

FRONT VIEW

(CENTER MOUNTING BRACKET SHOWN)

LEFT OUTER

MOUNTING BRACKET

LEFT SIDE

OUTER HOOD

LEFT SIDE

INNER HOOD

PIVOT BUSHING

10545C1.DWG

RIGHT SIDE
OUTER HOOD

RIGHT SIDE
INNER HOOD

CRADLES

PAN HE AD SCREW

RIV-NUT

9806-0965100

30" HOOD ASSEMBLIES

CENTER MOUNTING BRACKETS,

(1) LEFT AND (1) RIGHT

10545C1.DWG

Mount a pair of outer and a pair of center hood brackets as shown above. Lift the hoods, one at a time, onto their brackets,

making sure the pivot bushings sit in the bracket cradle on each side, as shown in the close-up illustration above.

RIGHT OUTER

MOUNTING BRACKE

UNIT BACK

UNIT FRONT

3 L25-007 Rev. 1 12/2001