USER AND INSTALLATION MANUAL
ENGLISH
FX-
COMM4NDER.
®
CO2 FX
CONTROL GEAR
PART01338
PART01174
rev 01-00
rev 01-01
DISCLAIMER
WARNING
© 2019 MAGICFX
All rights reserved.
Nothing from this publication may be copied, reproduced and/or published by
means of printing, photocopying or by any other means, without the prior written
approval of MAGIC FX.
MAGIC FX reserves the right to modify specications stated in this manual.
Read this manual carefully before installing and/or using this
product. Failure to read the manual and to follow the printed
instructions may lead to personal injury and/or damage to the
product.
®
TRADEMARKS
Any brand names mentioned in this manual are registered trademarks of their
respective owners.
LIABILITY
MAGIC FX accepts no liability for claims from third parties arising from unauthorised
use, use other than that stated in this manual, and use other than in accordance with
the General Conditions registered at the Chamber of Commerce.
We further refer to the General Conditions. These are available on request, free of
charge.
Although considerable care has been taken to ensure a correct and comprehensive
description of all relevant components, the manual may nonetheless contain errors
and inaccuracies.
Should you detect any errors or inaccuracies in the manual, we would be grateful if
you would inform us. This helps us to further improve our documentation.
2 MAGICFX® FX-COMM4NDER — User and Installation Manual
TABLE OF CONTENTS
Disclaimer 2
Trademarks 2
Liability 2
Foreword 4
Language 4
Revision table 4
1 Meet the MAGICFX® FX-COMM4NDER! 5
1.1 Main parts 5
1.2 Product identication 5
1.3 Technical data 6
1.4 Accessories 6
2 Fire safely! 7
2.1 General safety rules 7
2.2 Connecting FX-machines 7
2.3 Precautions for operation 7
3 Let’s re! 8
3.1 Connect the controller 8
3.2 Fire 10
3.3 Clean up 12
4 Maintenance 13
5 Troubleshooting 13
6 Correct disposal 13
7 EC Declaration of Conformity 14
MAGICFX® FX-COMM4NDER — User and Installation Manual 3
FOREWORD
Congratulations! You have bought a great new product from MAGIC FX.
This manual contains all information required for the intended use of the equipment.
Deviation from the described intended use can result in a hazardous situation and/or
property damage.
This manual includes notes and warnings on safe operation of the equipment. These
notes and warnings are accompanied by the following icons. Read them attentively!
DANGER
WARNING
CAUTION
NOTICE
Indicates a hazardous situation that, if not avoided, will result in
death or serious injury. This signal word is to be limited to the most
extreme situations.
Indicates a hazardous situation that, if not avoided, could result
in death or serious injury.
Indicates a hazardous situation that, if not avoided, could result
in minor or moderate injury.
Indicates information considered important, but not hazardrelated (e.g. messages relating to property damage).
LANGUAGE
This document contains the original instructions in English. In case you require other
languages please contact MAGIC FX.
REVISION TABLE
Doc nr Revision Date Description Author Approved
PART01174 01-00 14-11-2017 Initail release MBO TVA
PART01174 01-01 01-08-2019 A4 to A5 format TFR TVA
4 MAGICFX® FX-COMM4NDER — User and Installation Manual
1 MEET THE MAGICFX® FX-COMM4NDER!
The MAGICFX® FX-COMM4NDER is a 4 channel controller for 100 – 250 Vac ON/OFF
special eects machines. You can re multiple machines one at a time or
simultaneously.
1.1 MAIN PARTS
MASTER FIRE BUTTON
KEYSWITCH (ON/OFF)
POWER INPUT
(100 250 Vac)
4 RESETTABLE OUTPUT
FUSES (5 A)
4 SWITCHABLE POWER
ac)
1.2 PRODUCT IDENTIFICATION
FX LED INDICATOR
4 FIRE BUTTONS
SAFETY BUTTON
Main parts
Type plate
MAGICFX® FX-COMM4NDER — User and Installation Manual 5
1.3 TECHNICAL DATA
Product Product Name MAGICFX® FX-COMM4NDER
Product Code MFX3203
Product Type CONTROL GEAR
Main
Dimensions
Weight Weight 2.8 kg 6.2 lb
Package Length 348 mm 13.1 in
Environment Minimum Temperature -10 °C 14 °F
Electrical Voltage Input 100 – 250 Vac
Controlling Control Options Manual
Length 205 mm 8.1 in
Width 250 mm 9.8 in
Height 102 mm 4.0 in
Width 303 mm 11.4 in
Height 208 mm 7.6 in
Packaged weight 3.1 kg 6.8 lb
Maximum Temperature 50 °C 122 °F
Voltage Frequency 50 – 60 Hz
Power Consumption 15 W
Power Connector Neutrik
®
powerCON TRUE1 (in & out)
Power Output MAX 5 A per output with resettable
output fuse (max. 16 A in total)
Technical data
1.4 ACCESSORIES
Code Product Included
MFX0311 Neutrik
MFX0312 Neutrik
MFX0322 Neutrik
MFX0323 Neutrik
MFX0324 Neutrik
MFX0325 Neutrik
MFX0326 Neutrik
MFX0313 Schuko to Neutrik
6 MAGICFX® FX-COMM4NDER — User and Installation Manual
®
powerCON TRUE1 - Male to Female - Link cable 10 m
®
powerCON TRUE1 - Male to Female - Link cable 20 m
®
powerCON TRUE1 - Male to Female - Link cable 0.5 m
®
powerCON TRUE1 - Male to Female - Link cable 1.5 m
®
powerCON TRUE1 - Male to Female - Link cable 3 m
®
powerCON TRUE1 - Male to Female - Link cable 5 m
®
powerCON TRUE1 - Male to Female - Link cable 15 m
®
powerCON TRUE1 - cable 1.5 m X
Accessories
2 FIRE SAFELY!
The MAGICFX® FX-COMM4NDER has been designed and constructed in such a
manner that it can be used safely. This applies to the use, the circumstances and the
regulations as described in this documentation. Reading this documentation and
following the instructions are therefore necessary for everyone who is authorised to
work with the MAGICFX
®
The MAGICFX
FX-COMM4NDER must be used in surroundings that:
• Have a stable temperature of between -10 and 50 °C.
• Are free of dust, corrosive gases and high concentrations of organic vapours.
• Are not situated in the vicinity of a source of vibration.
2.1 GENERAL SAFETY RULES
• Only authorised persons may carry out work with the MAGICFX® FX-COMM4NDER.
• Do not use the MAGICFX® FX-COMM4NDER if there are people or animals in
the direct output.
• Make sure that children, unauthorised people and animals do not obtain
access to the MAGICFX® FX-COMM4NDER.
• Make sure there are no freestanding objects or objects that can be damaged
by the connected machines within the output distance.
• Do not remove any safeguards, safety caps and safety symbols.
• All required safety devices must be in good condition and function properly.
• Ensure sucient lighting of the surroundings.
• Keep the workplace clean.
• Refer to the manual(s) of the connected machine(s) for safety instructions
concerning the use of those machines.
®
FX-COMM4NDER.
2.2 CONNECTING FX-MACHINES
The voltage and frequency connected to the power input of the MAGICFX®
FX-COMM4NDER are also the voltage and frequency of the switchable power outputs.
With a maximum electric current per switchable output (see Chapter 1.2 Technical
Data), a deviant input voltage or frequency may cause connected FX-machines to
not work properly. The switchable output cannot deliver the power the FX-machine
might require.
2.3 PRECAUTIONS FOR OPERATION
WARNING
WARNING
Using a damaged controller can lead to death, serious injury or
property damage. Always inspect the controller thoroughly
before operation.
Unauthorized operation of the controller can lead to death,
serious injury or property damage. Never leave the controller
unattended when the machine is ready for use.
MAGICFX® FX-COMM4NDER — User and Installation Manual 7
3 LET’S FIRE!
POWER IN P OWER OUT POWER OUT POWER OUT POWER OUT
PowerCon TRUE1 female
3.1 CONNECT THE CONTROLLER
CAUTION
1 Place the controller on a stable surface in a suitable area.
2 Make sure the keyswitch is in the ‘OFF’ position.
3 Connect the PowerCon TRUE1 power cable to the power input of the controller.
Do not connect FX-machines to the switchable power output(s)
when the output cannot deliver sucient power to the FX-
machine. See Chapter 2.
POWER
4 Connect the other end to a power outlet.
8 MAGICFX® FX-COMM4NDER — User and Installation Manual
5 Connect up to four FX-machines to the controller with PowerCon TRUE1 link
PowerCon TRUE1 femalePowerCon TRUE1 male
cables.
POWER
POWER OUT POWER IN
6 Remove the key from the keyswitch when you leave the controller unattended.
MAGICFX® FX-COMM4NDER — User and Installation Manual 9
3.2 FIRE
1 Place the key in the keyswitch and set the keyswitch in the ‘ON’ position.
All buttons light up white.
2 Press the safety button.
The FX LED indicator and the safety button light up red.
NOTICE
10 MAGICFX® FX-COMM4NDER — User and Installation Manual
You cannot activate the safety button when other buttons are
pressed. Make sure all buttons are released when trying to
activate the safety button.
3 Press any of the re buttons to re the machine connected to the respective
output.
The pressed re button lights up red.
Alternatively, press the master re button to re all connected machines
simultaneously.
All re buttons light up red.
4 Enjoy the view!
5 When you are done with ring, press the safety button to deactivate the re
buttons.
The FX LED indicator turns o.
MAGICFX® FX-COMM4NDER — User and Installation Manual 11
3.3 CLEAN UP
1 Make sure the FX LED indicator is turned o.
Set the keyswitch to the ‘OFF’ position.
2 First disconnect the power cable from the FX-COMM4NDER. Then disconnect
the link cables.
3 Remove the machine.
12 MAGICFX® FX-COMM4NDER — User and Installation Manual
4 MAINTENANCE
To achieve the maximum service life of the MAGICFX® FX-COMM4NDER you must
regularly clean the MAGICFX
Contact MAGIC FX if the MAGICFX® FX-COMM4NDER is not functioning correctly.
DANGER
®
FX-COMM4NDER and test if it is functioning correctly.
Do not replace parts yourself; always consult MAGIC FX.
5 TROUBLESHOOTING
Always contact MAGIC FX if any malfunctions or errors occur that cannot be solved
with the instructions as described in this manual.
6 CORRECT DISPOSAL
This symbol on the product and / or accompanying documents
means that used electrical and electronic products should not be
mixed with general household waste. For proper treatment,
recovery and recycling, please take this product to designated
collection points where it will be accepted free of charge.
Alternatively, in some countries you may be able to return your
products to your local retailer upon purchase of an equivalent new
product.
Disposing of this product correctly will help save valuable resources and prevent any
potential negative e ects on human health and the environment, which could
otherwise arise from inappropriate waste handling.
Please contact your local authority for further details of your nearest designated
collection point.
Penalties may be applicable for incorrect disposal of this waste, in accordance with
your national legislation.
MAGICFX® FX-COMM4NDER — User and Installation Manual 13
7 EC DECLARATION OF CONFORMITY
According to Annex III A Low Voltage Directive 2014/35/EU
MAGIC FX B.V. declares as manufacturer and composer of the technical construction file that the
product with the following specifications:
Name machine
Type
Voltage
Serial number
Year of construction
Is in conformity with the minimal safety regulations as stated in the following directive(s):
• EMC (2014/30/EC) ElectroMagnetic Compatibility
• RoHS (2011/65/EU) Restriction of the use of certain Hazardous Substances
• WEEE (2012/19/EU) Waste Electrical & Electronic Equipment
The following harmonized standards were applied:
• NEN-EN-ISO 12100:2010, Safety of machinery - General principles for design - Risk
assessment and risk reduction.
• NEN-EN-IEC 60204:2010, Safety of machinery - Electrical equipment of machines - Part 1:
General requirements.
• NEN-EN-IEC 61000-6-3:2007/A1:2011, Electromagnetic compatibility (EMC) - Part 6-3:
Generic standards - Emission standard for residential, commercial and light-industrial
environments.
Original declaration of conformity
Translation of the original declaration of conformity
Name manufacturer : MAGIC FX BV
Address : Schouwrooij 27, 5281 RE BOXTEL
Country : The Netherlands
CEO : B. Veroude
Date : 6-10-2017
: FX-COMM4NDER
: MFX3203
: 100-250Vac 50-60Hz
: on product
: on product
Signature :
14 MAGICFX® FX-COMM4NDER — User and Installation Manual
WWW.MAGICFX.EU
Loading...