Magic Chef MCKC490B Owner's Manual

4.9 CU.FT. BEER KEG COOLER

INSTRUCTION MANUAL

Model No.: MCKC490B

To ensure proper use of this appliance and your safety, please read the following instructions completely before operating this appliance.

TABLE OF CONTENTS

Names of the Parts _________________________________________________3

Important Safety Instructions ________________________________________ 4

Installation Instructions _____________________________________________4

Before Using Your Beer Dispenser ____________________________________ 4

Installation of Your Beer Dispenser ________________________________ 4 - 5

Electrical Connection _______________________________________________ 5

Installation Instructions for Beer Keg_______________________________ 6 - 9

Dispensing of Beer _________________________________________________ 9

Operating Your Beer Dispenser _____________________________________ 10

Setting the Temperature____________________________________________ 10

Automatic Defrosting ______________________________________________10

Converting to an All Refrigerator ____________________________________ 10

Changing the Reversible Door_______________________________________11

Care and Maintenance _____________________________________________ 12

Troubleshooting Guide_____________________________________________12

Warranty ________________________________________________________ 13

NAMES OF THE PARTS

MODEL NO.: MCKC490B

1 Beer Tower 2 Plastic Gasket 3 Safety Guard Rail 4 Drip Tray 5 Adjustable Thermostat 6 CO2 Regulator 7 CO2 Gas Cylinder 8 CO2 Gas Cylinder Support 9 Evaporator 10 Reversible Door 11 Beer Keg (not included) 12 Metal Plate 13 Metal Washers(2) 14 Castors with Lock (4)

IMPORTANT SAFETY INSTRUCTIONS



WARNING



• Read all instructions before using the unit.

• WARNING: Risk of child entrapment.

• To avoid the possibility of child entrapment, please take the following precautions

before throwing out the appliance.

- Remove all doors from the unit.

- Leave the shelves in place so that children may not easily climb inside.

• Before you throw away your old unit: Take off the doors. Leave the shelves in place so that children may not easily climb inside.

• Never allow children to operate, play with, or crawl inside the unit.

• Refrigerants: All refrigeration products contain refrigerants, which under the

guidelines of federal law must be removed before disposal of product. It is the consumer’s responsibility to comply with federal and local regulations when disposing of this product.

• Never clean unit parts with flammable fluids. The fumes can create a fire hazard or explosion.

• Do not store or use gasoline or any other flammable vapors and liquids in the vicinity of this or any other unit. The fumes can create a fire hazard or explosion.

-Save these instructions-

To reduce the risk of fire, electrical shock, or injury when using your Beer Dispenser, follow these basic precautions:

INSTALLATION INSTRUCTIONS

 Before Using Your Beer Dispenser

• Remove the exterior and interior packing.

• Check to be sure you have all of the following parts:

• 1 Safety Guard Rail

• 1 Drip Tray (2 Pieces)

• 1 CO2 Cylinder Support

• 1 CO2 Regulator (Box)

• 1 CO2 Empty Cylinder(Box)

• 1 CO2 Air Line Hose (Red)

• 1 Beer Keg Coupler (Box)

• 1 Beer Tower

• Before plugging in the keg cooler, let it stand upright for approximately 2 hours. This will

reduce the possibility of a malfunction in the cooling system from handling during transportation.

• Clean the interior surface with lukewarm water using a soft cloth.

 Installation of Your Beer Dispenser

• This appliance is designed to be free standing only, and should not be recessed or built-in.

• Place your Beer Dispenser on a floor that is strong enough to support the Beer Dispenser

when it is fully loaded.

• Allow 3 inches of space between the back and sides of the Beer Dispenser, which allows the

proper air circulation to cool the compressor.

• Locate the Beer Dispenser away from direct sunlight and sources of heat (stove, heater,

• 1 Pull Handle (Beer Tower Faucet)

• 1 Metal Wrench

• 4 Plugs: For Guard Rail Holes

• 1 Metal Plate For Cabinet Bottom

• 2 Steel wire shelves

• 1 Steel Clamp for Red Hose

• 4 Castors with locks

• 2 Metal Washers

radiator, etc.). Direct sunlight may affect the acrylic coating and heat sources may increase



electrical consumption. Extreme cold ambient temperatures may also cause the Beer Dispenser not to perform properly. This unit is not designed for outside installation (ie garages, porches, etc.)

• Avoid locating the Beer Dispenser in excessive humidity.

• Plug the Beer Dispenser into a dedicated, properly installed-grounded wall outlet. Do not

under any circumstances cut or remove the third (ground) prong from the power cord. Any questions concerning power and or grounding should be directed toward a certified electrician or an authorized service center.

• After plugging the appliance into a wall outlet, allow the unit to cool down for 2-3 hours before

placing any contents in the Beer Dispenser compartment.

 Electrical Connection

Improper use of the grounded plug can result in the risk of electrical shock. If the power cord is damaged, have it replaced by an authorized service center.

Warning

This Beer Dispenser should be properly grounded for your safety. The power cord of this Beer Dispenser is equipped with a three-prong plug which mates with standard three prong wall outlets to minimize the possibility of electrical shock.

Do not under any circumstances cut or remove the third ground prong from the power cord supplied.

Use of extension cords is not recommended.

This Beer Dispenser requires a standard 115/120-volt, 60Hz electrical outlet with three-prong ground receptacle. The cord should be secured behind the Beer Dispenser and not left exposed or dangling to prevent accidental injury.

Never unplug the Beer Dispenser by pulling the power cord. Always grip the plug firmly and pull straight out from the receptacle.

WARNING

CO2 GAS CAN BE DANGEROUS

WARNING: CO2 cylinders contain high-pressure compressed gas which can be hazardous if not

handled properly. Make sure you READ and UNDERSTAND the following procedures for CO2 cylinders BEFORE INSTALLATION.

1. ALWAYS connect the CO2 cylinder to a regulator. Failure to do so could result in explosion

with possible injury when the cylinder valve is opened.

2. NEVER connect the CO2 cylinder directly to the product container.

3. ALWAYS follow correct procedures when cylinders are changed.

4. ALWAYS secure the cylinder in an upright position.

5. NEVER drop or throw a CO2 cylinder.

6. ALWAYS keep a CO2 cylinder away from heat. Store extra cylinders in a cool place

(preferably 70°F). Securely fasten with a chain in an upright position when storing.

7. ALWAYS ventilate and leave the area immediately if CO2 leakage has occurred.

8. ALWAYS check the D.O.T. test date on the cylinder neck before installation. If over five (5)

years, do not use, return cylinder to gas supplier.

9. NEVER connect a product container unless there are two (2) safety’s in the pressure system:

a. One at or on the CO2 regulator b. One at or on the product coupler or in the pressure gas line.

+ 9 hidden pages