Magicar m110as bruger User Manual

Download

Page 1

Thank you.

Thank you for your purchase of an

MAGICAR

alarm and/or remote-start sys-

tem.

MAGICAR

alarms and remote-start systems are the most advanced sys-

tems on the market with amazing features, incomparable ease of use, and

breakthrough technologies never before used in the automotive environment.

Please take time to read and understand this owner's manual so that you can

fully use and enjoy you new

MAGICAR

system.

Two-Way Remote User’s Guide

Page 2

Two-Way Remote User’s Guide

Page 3

Two-Way Remote User’s Guide

LCD Screen

LCD ICONS

Remote Description

Techinical Specification

Before using your Magicar system, please take some time to familiarize yourself with it.

Front

Back

Application

Frequency

Stability

Exterior

433.92Mhz

2ppm/year

86 39

20 (mm)

Weight

Transmitting

Output

Operating

Temperature

33.5g

(without Battery)

10 mW

-15°C ~ +50°C

Timer Function On

Turbo Function On

Passive Function On

Auto Function On

On - Siren will chirp when arming or disarming.

Off- Siren will not chirp when arming or disarming. The siren will still be activated if the alarm is triggered or PANIC mode is activated.

On - Remote will vibrate (when applicable), and give audible confirmation.

Off - Remote will only vibrate (when applicable), no audi ble confirmations will be given.

Buttons

Battery Door Lock

Battery

1.5V (AAA)

Antenna

Color LCD Screen

Page 4

On - Impacts to the vehicle will be ignored by the alarm.

Off - Impacts to the vehicle, depending on the severity, will trigger the alarm.

Alarm Clock On

Ignition Control Door Lock.

Doors locked/unlocked.

Door open.

Remote Start Availability Indication

Trunk open.

This icon displays the signal strength while transmitting or receiving.

Display of remaining remote control battery life.

Impact to the vehicle is detected.

Indicates that someone is using the RPS to page you from your vehicle.

Car Call function using the RPS is on.

AUX mode on

Parking lights are flashing.

Voltage display.

Cold Start Function On

Hood Open

Displays current time, remote start runtime, remaining, turbo mode time inside temperature of the vehicle, battery voltage of the vehicle, start reservation time, failure of signal transfer.

Each icon will be displayed while the function it corresponds to is operating. The screen may be hard to see in direct sunlight.

Indicates that the vehicle is currently remote-started.

Used while displaying temperatures and other features.

Valet mode is on, only the door lock function will be available.

Note

Two-Way Remote User’s Guide

Page 5

Two-Way Remote User’s Guide

Button Functions Description

0.5 sec: press shortly (between 0.5 and 1.0 sec.) : press until a car responds (longer than 2 sec.)

+: Press two buttons at the same time. Performing the same button functions again will toggle the various modes between on and off.

Note

snoit

cnu

Fsno

ttuB

1 I

0.5Sec ARM/DISARM Arming(Locking)/Disarming(Unlocking)

2 I

I 0.5Sec AUX #1 Activates AUX #1 output

2Sec START/STOP If the remote start availability icon is on,

this will start the remote start process If the remote start was running, this will stop the remote atart process.

3 III 0.5Sec AUX #2 Activates AUX #2 output

2Sec Trunk Trunk release. Tap Twice Back Light On The backlight of remote is turned on for 10Sec

4 IV

0.5Sec Query Car Check function

-1st tap:Vehicle temperature

-2nd tap:Voltage of vehicle battery

-3rd tap:Voltage of remote battery In valet mode, it shows valet.

2Sec Button HOLD Button hold on/off 4Sec Panic Panic mode (for 90sec) Tap Twice Parking Timer Paking timer on/off

5 (I+II) 0.5Sec MUTE Siren chirp on/off

2Sec PROGRAM #1 Main controller option #1

(I+III) 0.5Sec VALET Valet mode on/off

2Sec

SHOCK ON/OFF Shock Sensor on/off

(I+IV) 0.5Sec DRIVE LOCK Drive lock(lgniion door lock) on/off

2Sec PROGRAM #2 Main controller option #2

(II+III) 0.5Sec

PASSIVE ON/OFF

Passive arming on/off

2Sec MENU Entering into Remote menu

9 (II+IV) 0.5Sec TIME ON/OFF TIME starting reservation on/off

2Sec AUTO ON/OFF Auto door on/off

10 (III+IV) 0.5Sec TURBO ON/OFF Turbo function on/off

2Sec AUX ON/OFF AUX mode on/off

2Sec Extension If the vehicle is remote started or turbo

operated, the runtime will be extended.

Page 6

Two-Way Remote User’s Guide

Unlocking/Disarming

If the system is locked/armed, pressing button

for a half second will unlock the doors and disarm the alarm. This function will still operate even while the vehicle is remote started. The remote and vehicle will chirp twice.

Beeps two, four times

1) Disarming

The door(s) will be unlocked the RPS LED will stop flashing, and the following details will be indicated according to the number of chirps and parking light flashes:

Twice: No trouble while the system was armed. Four times: Alarm was triggered by strong impact or a opened door.

2) Auto Rearm

If a door has not been opened within 30 sec. of disarming the alarm, the doors will be relocked and the alarm will arm. This feature is meant to protect against an accidental disarm of the system. To prevent the rearm process, simply open a door within 30 sec. of disarming the alarm. The system will not arm again until given the command through the remote.

In the alarm has been triggered, press button I

. The siren will stop, but the alarm will still be armed. The system will not respond for the first few seconds after the alarm was triggered, this is because it is still trying to send a signal out to the remote during that time.

Press button

I again to disarm the alarm.

Note

Locking/Arming

If the system is unlocked/disarmed, pressing button I for a half second will lock the doors and arm the alarm. This function will still operate even while the vehicle is remote started. The remote and vehicle will beep once.

Beeps once

1) Arming

Red LED of Car Call sensor flashes, and the doors, shock sensor and Car Call are monitored.

2) Door Trigger

If the alarm is armed and a door is opened, the alarm will be triggered, playing the siren and flashing the parking lights for 30 seconds. (Even if the Siren Chirp is turned off.)

3) Shock Sensor

If the shock sensor detects a heavy impact to the vehicle after 30 seconds of the alarm being armed, the alarm will be triggered, playing the siren and flashing the parking lights for 9 seconds. The remote will be notified of the impact and will beep rapidly while displaying the impact icon; a person hitting the wind shield. The siren will not play at this time if the Siren Chirp has been turned off. In the case of a light impact, the siren will chirp four times, and the remote will display the impact icon.

4) RPS (Remote Paging Sensor)

If the RPS sensor is triggered while the alarm is armed, the remote will be paged and will display the RPS icon.

Siren may go off if you arm the vehicle while the hazard lights are on.

Page 7

Two-Way Remote User’s Guide

AUTO Mode (ON/OFF)

Pressing button

and

for 2 sec. will turn on Auto mode. With Auto mode, the vehicle will unlock/disarm when the remote is getting closer, and lock/arm when the remote is far away.

1) Automatic door lock/unlock function starts.

Operating distance may differ from vehicle and different environments. This function works on the following order:

Press button

again for 2 sec. to switch to the next mode.

dodoreremimifafamimireredodo

2) When the door is locked

beep beep beep beep

3) When the door is unlocked

Auto mode 3 suspends AUTO mode when it senses consecutively arming/disarming signals. The suspension above is cancelled by pressing button

once.

Auto Mode 1

Auto Mode 2

Auto Mode 3

OFF

Short distance

Long distance

No operation

Icon on.

Icon flashes in 1.5 second intervals.

Icon flashes in 0.5 second intervals.

Icon off.

Beeps once

Due to varying vehicles and environments, there may be a small area of distance in which the system thinks the remote is far enough away to lock, and, close enough to unlock. If your remote is within this area, the system will repeatedly arm and disarm. To avoid this situation, try placing your remote farther away from the vehicle.

Auto mode will drain your remote battery faster than normal.

Weather and temperature differences will affect the operation distance of Auto mode.

Note

3) RPS Display

When disarming, if the RPS was triggered while the system was armed, the

numbers of times it was triggered will be displayed.

4) Function of Shock Alarm

When disarming, if the Shock Sensor was triggered while the system was armed, the numbers of times it was triggered will be displayed.

Page 8

Two-Way Remote User’s Guide

AUX Mode Entry (ON/OFF)

As you enter AUX mode, the icon will be displayed. If an auxiliary channel is not triggered within 60 sec., Aux mode will be cancelled. An auxiliary channel can be programmed for a pulsed, latched, or timed latch output. You can use them to open or close windows, turn on lights, activate heated seats, and other features. Please follow instruction.

Beeps once

1) AUX 1 (optional)

After entering AUX mode, AUX 1 output will be triggered, if button IIis pressed for 0.5 sec. While operating AUX 1, the remote control will indicate that AUX 1 is operating.

2) AUX 2 (optional)

After entering AUX mode, AUX 2 output will be triggered, if button

III is pressed for 0.5 sec. While operating AUX 2, the remote control will indicate that AUX 2 is operating.

Options that utilize auxiliary outputs generally cost extra for installation.

Note

Remote Start (ON/OFF)

The vehicle will start and run for a preset time if button

is pressed for 2 sec. If the vehicle is a diesel, the system will pause for a moment after turning on the ignition to allow time to glow plug warm-up. (If needed.)

Vehicle will be armed (if unarmed before start) by getting the signal from remote. If the vehicle fails to start, a second and third attempt will be made. Remote Start will run for the preset time (10, 25, 3, 5min.). If button II is pressed again for 2 sec. Remote Start will shut off. The remote start running will continue for 20sec after a door opens. The car key needs to be in On position within the 20 seconds. After the vehicle has been remote started, the remaining run-time will be displayed on the screen. If the timer goes 1 minute, the remote will warn your with (beep) that the vehicle is about to shut off.

Beeps three times

The remaining time is 9min. and 50 sec.

Remote starting should be avoided while people are inside

the vehicle.

You will need to turn the key to the ON position in order to drive the vehicle. Turning the key past the ON position could cause damage to the vehicle starter.

Page 9

1) Extension of Remote Start Timer

During the running time, if you press button I

for 2 sec.

“ Start-Again”

will scroll across the screen once and the timer will be reset to the preset time.

2) Remote Start Display

If the remote start confirmation is not received by the remote for different reasons, pressing any button within range of the vehicle will update the remote and show the remaining run time.

Two-Way Remote User’s Guide

~Beeps three times after resetting the runtime.

The remaining runtime will be reset.

~Beeps three times after resetting the runtime.

Two-Way Remote User’s Guide

Trunk Release

The trunk will be opened/unlocked, if a button III

is pressed for more than 2 sec. If

the alarm is on, it will disarm and unlock the doors as well.

If the vehicle has not a trunk actuator, it may be conve nient to put the system in Valet mode if you are going to be in the trunk doing work for an extended period of time. If the vehicle trunk release is a cable type and not electric, extra installation steps will be required to make the remote trunk release functional. On vehicles with a trunk actuator, if the trunk is opened more than 20 sec. while the vehicle is remote started, the remote start will be cancelled and the vehicle will shut off.

Beeps twice.

If trunk sensor is installed in a manual transmission vehicle, opening trunk will cancel the remote start reservation.

Installation of a trunk open sensor or connection of the sensor wire will generally cost extra as it is an optional feature.

Note

Page 10

Two-Way Remote User’s Guide

Query Function

If button IV

is pressed for 0.5 sec., the remote and vehicle will respond with

beeps/chirps and parking light flashes to report the status of the vehicle.

Division

Armed, Remote Start OFF

Disarmed, Remote Start OFF

Armed, Remote Start ON

Disarmed, Remote Start ON

Car Inspection

Peep

Peep Peep

Peep Peep Peep

Peep Peep Peep Peep

Remote Control Operation

Beep Beep Beep

Beep Beep

Beep Beep Beep Beep Beep Beep

Beep Beep Beep Beep

1) When armed:

The icons of door lock, shock and Car Call flash.

2) When disarmed:

The icon of unlock flashes. Door will be opened.

3) Car

s Indoor Temperature Indication

Internal temperature of vehicle will be indicated with

℃

. (However, the temperature indicated is the temperature of where a sensor is located, and if temperature sensor doesn

’

t exist, FAIL will be indicated)

The temperature sensor can be located in a specific location per a customer

’ s

request by using the extended cable if needed. (Option)

4) Car

s Battery Voltage Check

In checking the conditions of a car, the battery voltage of a car can be checked with the numbers, if a

button is pressed for 0.5 second, once.

5) Remote Control

s Battery Check

After checking the voltage of a car, the battery voltage of a remote control can be checked with the numbers, if a IVbutton is pressed for 0.5 second, once.

The menu will change from

in order, if a

button is

pressed.

Changes of Menu

These functions should be operated within transmitting and receiving range

of the vehicle.

Note

Panic Mode

four seconds

If button

is held for more than 4 sec., Panic mode will be initiated. The doors will

lock, the parking lights will fl ash and the siren will play for 1 min. and 30 sec.

“

PANIC

”

will scroll across the remote screen for 30 sec.

By pressing buttons

I + II

for 0.5 sec, at the same time, the siren chirps from the vehi-

cle will be muted. To un-mute the siren chirps, press buttons

I + II

for 0.5 sec. again.

Canceling Panic Mode

In operating self-emergency, remote control will be turned off, in the case of remote wakeup. In operating self-emergency, a siren will operate for 1 min 30sec, in the case of car silence.

To cancel Panic mode, press button

for 0.5 sec.

Flashes for 30 seconds.

You can use this feature to draw attention to you and your vehicle if you are attacked or otherwise threatened.

Note

Exception

The siren will still play in these situations: If the alarm is triggered by opening the trunk or a door. The siren will still be silent if the alarm is trigger via the shock sensor. If Panic mode is activated.

Siren Chirp (ON/OFF)

10.

Page 11

Two-Way Remote User’s Guide

Valet Mode (ON/OFF)

Activate Valet mode by pressing buttons

III

for 0.5 sec. at the same time. (Valet mode can also be activated with the ignition key as well, see page 36.) Valet mode will put the system to sleep and a lmost all func tions will be disabled. Remote lock/unlock, code unlock, remote option programming, and the query function will still operate.

1) Valet Mode OFF

Pressing buttons

I + III

for 0.5 sec. at the same time again will turn Valet mode

OFF, which restores all functions to the remote.

2) Valet Mode Display

The only functions available will be:

1. Button I for 0.5 sec. (lock/unlock)

2. Buttons I + III

for 0.5 sec. (Valet OFF)

3. Button

IV for 0.5 sec. (Query Function)

4. Button III double press. (EL Lamp ON)

5. Buttons

II + III for 2 sec. (Remote Set-Up)

If any other functions are attempted, the remote will beep three times and “

SLEEP

”

will scroll across the screen to indicate that the system is in Valet mode.

Beeps three times.

When the system is in Valet mode, the alarm is not active, even when the doors are locked. Any starter or ignition kill systems that have been installed will be disabled as well.

If you loan your vehicle to someone who is not familiar with this CompuStar system, you may want to use Valet mode to avoid any problems they might have by accidentally activating various features.

Shock Sensor (ON/OFF)

To turn off the shock sensor, press buttons

III

for 2 sec. The shock sensor is turned off if the [ ] icon is displayed on the LCD of the remote. This mode is useful if you will be parked in a loud or high traffic area such as an airport. Turning the shock sensor off will help prevent false alarms.

Beeps once

[ ]

Drive lock icon “

[ ]

” will be displayed on remote control, by pressing I+ IV

buttons for 0.5 sec at the same time, and the doors will be locked right after brake padal is pushed

Drive Lock OFF

Drive lock will be OFF, and drive lock icon will be turned off, again by pressing

I+

buttons for 0.5 sec at the same time.

Drive Lock function is not activated:

during remote start, a door opens within 30 seconds after ignition is turned on, a door is open when the vehicle is started with key.

Doors will be unlocked when ignition is turned off.

Drive Lock(Ignition control door lock) (ON/OFF)

Page 12

Two-Way Remote User’s Guide

Timer start reservation is activated by pressing buttons

at the same time for 0.5 sec if timer has been set up. Once activated, the vehicle will start by itself at preset time in every 24 hours . (See page 42-Timer Start Set-Up)

Timer Start Reservation (ON/OFF)

Beeps once

Timer Start Reservation

To turn off Timer Start, press buttons

buttons at the same time for 0.5 sec.

The siren will beep twice and the parking lights will flash.

※

However, for a manual transmission vehicle, the remote start reservation is required for this function to work.

The, timer start reservation and turbo mode functions are not turned from the factory, these options must be turned on before use.

Note

Passive Arming (ON/OFF)

Passive Arming, which will lock/arm the vehicle if it is disarmed, after 30sec, can be turned ON by pressing buttons

III

at the same time, it operates under the following

conditions.

After remote start reservation is complete in a manual transmission vehicle. In the case of turbo function ON, after the door is open and closed following the

removal of Key

2) Passive Arming OFF

To turn off Passive Arming, press buttons

III

buttons at the same time for 0.5

sec. The siren will beep twice and the parking lights will flash.

Beeps once

If Passive Arming is ON, the doors will be locked automatically, the remote should be taken with you when you leave the vehicle so that it does not get locked inside. If you will be staying in the vehicle for an extended period of time without the engine running, you should turn Passive Arming off so that it does not become a nuisance.

While ignition is off after the door is open and closed. When the alarm is disarmed.

1) Instant Locking

Page 13

Two-Way Remote User’s Guide

Parking Timer (ON/OFF)

tap twice

4) Parking Timer Release

Parking timer will be turned off with a chirp from the remote, if buttons

are

pressed for more than 2 sec, while the parking timer is on.

Beep twice, 4 times

2min and 30 sec has passed.

1) Parking Timer

The Parking Timer can be used to monitor the time passed while driving or being

parked.

2) Parking Timer Set-up

By pressing buttons

twice, the parking timer will be set up and the remote will

beep

3) Parking Timer Display

After starting the parking timer, the display will alternate between the present time

(for 1 sec.) and the parking timer (for 2 sec.)

The parking time will also shows on tenth of a minute

The maximum display time of the parking timer is 99 hours 59 min.

(Continue for 2 sec alternating with the present time)

In the case the door is unlocked in the middle of turbo operating, engine will shut

off in 20 seconds assuming that owner will be ready to drive the vehicle.

Beep twice, 4 times

1) Turbo Function OFF

Turbo Timer will be turned off with a chirp from the remote, if buttons

III

are

pressed for 0.5 sec.

If you pressing button

III+IV

while engine is running by Turbo Timer, both engine

and Turbo Mode will be turned off

2) Check Function of Turbo Time

The remaining time is displayed, and turbo icon will flash

(The remaining time of turbo will be displayed

for 1 minute and 1/2 sec)

Turbo Function (ON/OFF)

Turbo function can be turned on by pressing buttons

III

for 0.5 sec. With Turbo mode active, the vehicle will stay running after the key has been removed from the ignition

In the case that Key is removed and the door is locked, wakeup will maintain for turbo function set-up time, however, a car whose auto alarming function is ON will be immediately locked.

In the case that turbo operating time is set-up for 1 min, wakeup will maintain for a while, if Key is removed, but the door unlocked/locked doesn

’

t work.

To stop the vehicle from running via the Turbo Timer, press button

for more than 2 sec. (In the case of a manual transmission vehicle, remote start reservation will be maintained.)

Page 14

Two-Way Remote User’s Guide

Beep once

Flashes 5 times

2) Button Hold Cancellation

To cancel the Button Hold function, press button

IVfor 2 sec. again while the

Button Hold function is active. The remote will beep twice, and the normal func tions will return to the remote.

3) Button hold Display

Normally, Button Hold operation is indicated on the right side of the screen as an“H”

The Button Hold function will be cancelled if you activate Panic mode by

pressing button IV

for 4 sec.

Note

2 sec

Button Hold Functions

This function prevents accidental button presses while carrying your remote.

1) Button Hold Set-up

To activate the Button Hold function, press button

for 2 sec. The remote will

beep and display

“

Hold

”

on the screen.

Double Tap

If it is hard to see the screen because of low light conditions, tap button III

twice, the

EL Lamp will be turned on.

Beep

EL Lamp is

turned on

3) Turbo Time Extension

Pressing button

for more than 2 sec. while the turbo timer is operating will

extend the run time, as

is scrolled across the display.

A turbo timer is designed for vehicles with turbo chargers. After hard use, the turbo housing will be very hot and allowing the vehicle to idle for a few minutes will cycle more oil through the turbo while it cools.

Turbo Function works differently with LPG option vehicles. Warning! Since engine is running without key with this Turbo Mode, the dri ver should make sure that the vehicle’s gear is in neutral.

Note

Beep twice, 4 times

(1:57 will be displayed when 2 minute Turbo

Timer is activated)

EL Lamp

Page 15

Warning of vehicle battery drain

Two-Way Remote User’s Guide

One flashing light

If the vehicle is locked (armed) with a taillight on, the parking lights will flash once and siren will chirp 7 times

With this sensor installed and the alarm armed, the alarm will be triggered if the trunk is opened. The siren will be activated and the parking lights will flash.

With this option installed: If the door is forced open, while the vehicle is armed/locked, the vehicle will not start with either the remote or key.

For remote starting diesel vehicles, the system monitors Wait to start lights to preheat the engine.

Options will generally cost extra for installation and parts.

Note

Two-Way Remote User’s Guide

Trunk Open Sensor

Wakeup Interception Function

Preheating Sensor

Page 16

Two-Way Remote User’s Guide

If the alarm is armed and the shock sensor is triggered by an impact to the vehicle, the following sequence will occur:

If the alarm is armed and the door, trunk, or hood is opened, the following sequence will occur:

If the alarm is armed and the RPS function is turned on, when a person knocks on the RPS sensor, the remote will be paged and will ring like a telephone and vibrate.

Shock Sensor Trigger

Theft Function (Door, trunk or hood trigger)

Car Owner Calling Function

Beeps for 9 sec

Beeps for 30 sec

Beeps

CAR :

The siren will activate and the parking

lights will flash for 9 sec.

Remote contro l : Vibration/ theft i ndication sound. Remote will beep at 4 second intervals until a button is pressed.

CAR : The siren will activate and the parking lights will flash for 9 sec.

Remote control :

Vibration /theft ind ication sound. Remote will beep at 4 second intervals until a button is pressed.

CAR :

The vehicl e LED change s fro m red to

green.

Remote control :Vibration/telephone ring. (4 times) Remote will beep at 6 second intervals until a button is pressed.

Page 17

Two-Way Remote User’s Guide

Cold Start Functions

This is the function that when the timer start reservation is on, engine will be started automatically based on fixed 3 steps of temperature setting if the temperature is below 0

, the engine will be started automatically Temperature setting can be adjusted by changing main controller option.

Beeps

CAR :

The siren will activate and the parking

lights will flash for 9 sec.

Remote control :

Vibration /theft ind ication sound. Remote will beep at 4 second intervals until a button is pressed.

It perceives someone is inside the car, and makes car alarm activated and transfer the siginal to the remote controller when it detects someone is inside the car This is an optional product.

Beeps for 30 sec

CAR :

The siren will activate and the parking

lights will flash for 9 sec.

Remote control :

Vibration /theft ind ication sound. Remote will beep at 4 second intervals until a button is pressed.

Ultra Sonic Sensor (Optional)

Cold Start Functions

Code Unlock Function

Enter the four numbers (1111~9999) as a password, by using a RPS sensor, entering the correct pass code will unlock the doors, without either remote control or Key. (“0” should be avoided for a password.)

If you enter the wrong password more than 5 times within 30 min, this

function will not be available for 24 hours. (The remote will still operate during this 24 hour period.)

If you give up in the middle of entering the password, it will not count

toward the wrong entry count of 5.

Note

Conditions for Entering the Password the First Time

Key On, but Engine Off

Doors Unlocked

Door Open

Each knock in a set needs to be done within 1.5 sec. of each other. Waiting longer than 1.5 sec will switch to the next set of knocks. Green LED should be checked at the first knock. Conditions for Entering the Password the First Time

Page 18

Two-Way Remote User’s Guide

Knocking (For door open or entering the password.)

Two-Way Remote User’s Guide

The password should be entered under the, (see page 28).

After the first set

The second, third, and fourth password numbers should be entered the same as above. (As the password has four numbers.)

After entering the final set

The parking lights will flash, signaling that the password has been entered.

Unlocking the doors using the RPS

To unlock the doors using the RPS, the code must be entered correctly, matching the code you specified initially. The remote will be paged and will show that the doors have been unlocked.

The Green LED will flash at the first knock.

After 1.5 sec

The next knock shall be done within 1.5 sec.

Red LED fla shes as many times as the number of the first set of knocks.

Push the Button or Knock on the

RPS sensor 10 times

Push the Button orKnock as many times as the first password number, and then

check to see if the red LED flashes. (Knock as many times as the first password number)

Red LED flashes fastRed LED flashes fast

Green LED will flash at the first knock.

In Range Display Method

If the remote and vehicle are within operating range of each other, the signal strength will be displayed beside the antenna icon on the display.

Set-up and Other Functions

Flashes 5 times

When the battery is almost dead and ready to be replaced, the battery icon will flash and Battery Save Mode will operate.

Battery Save Mode Operation

The remote will only receive confirmation signals for button

operations. The other buttons will still function, but they will not receive confirmation signals back from the vehicle. The transmitting power will be reduced for a close range operation only.

Flashes 5 times

Battery Save Function

Page 19

Two-Way Remote User’s Guide

Time Information Backup

Door Open Indicating Function

1) It saves time information (current time, start-up reservation time and alarm time) in the status where power has not been supplied to remote (at a time of replacing batteries). If the power is supplied again, users do not have to re-adjust the time information.

2) Remote default is set in the status when the time information backup is released. In order to set up the time information backup for the remote, users need to execute the menu of the remote once or more. After users execute the menu ((2+3)-), the time information backup is automatically executed.

3) Cautions at a time of replacement of batteries In order to use the time information backup function more effectively, press button No.4 of the remote before and at a time of the replacement of the batteries (communication with the main not needed at that time) to back up more accurate time information.

The parking lights will flash to indicate that the door is open. (See INSTALLATION MANUAL for the setup procedure “the main option”)

GAS(LPG) Option Set-up

※ Burning off gas residue in the system:

In Turbo Mode, if Key is turned OFF but the GAS valve is not shut off, then the engine will be turned off in 4 minutes without burning off the gas residue.

In Turbo Mode, the remote will show the engine running to burn off the gas residue.

Note

Auto Transmission Car

- While engine is running, shut off the gas valve and wait. Then turn off the key after the gas residue was burnt off.

- Activating Turbo Mode will be a convenient way of burning off the gas residue since engine will continue running like a manual transmission vehicle until the gas residue is burnt off. See below.

Manual Transmission Vehicle

Turn off the key first then shut off the gas valve. Engine will continue running until the gas residue is burnt off. If you open and close the door while engine is still run ning, the remote start reservation is also completed.

Remote Start

After remote start is completed, the ignition wire will continue to be powered for 4 more minutes (or 4 minute and 20 seconds if a door opens while engine is running) by the system to make sure the gas residue is burnt out.

Page 20

Two-Way Remote User’s Guide

When this product is installed in a manual transmission vehicle, it must be set to Manual Transmission Mode. Our company is not responsible for any accident resulting from selecting wrong mode (Automatic Transmission Mode) for a Manual Transmission vehicle. Customer must confirm this with his/her installer and check and inspect by himself/herself.

Automatic transmission vehicles must be checked in the same manner, ensuring that the vehicle will not start with the key

Reservation Mode prevents a manual transmission vehicle from starting in gear if the system has been installed properly.

When key is turned off, the doors will unlock and the engine will remain running up to 2 minutes. Within the 2 minutes, if a door opens then closes, the engine will shut off completing the remote start reservation.“

[ ]”icon shall be displayed to confirm

the reservation.

In the process of Reservation mode set up, the display lights in the instrument cluster may be ON for 3 sec after the engine has been turned off. (This is a normal process.) In the process of Reservation mode set up, when the key is removed, the ABS light may be ON/OFF, this is a normal operation.

Note

Automatic(Passive) Reservation

If button II is pressed for more than 2 sec., before the key turned off and removed from the ignition, the parking lights will flash and the siren will chirp one time. The engine will stay running for 2 min. even if the key is taken out of the ignition. Before the 2 min. timer expires, you must get out of the vehicle and shut the door. Once the door closes the engine will shut off and Reservation mode has now been set. The remote start availability icon, “[ ]

”

will be displayed on the remote screen.

Active Reservation

This procedure is for the vehicles that have a problem with the Automatic Reservation

procedure.

Remote Start Reservation Mode for Manual Transmisson Vehicles

Number of Flashes

Once

Twice

3 times

4 times

5 times

Error Explanation

Engine is already running.

Ignition (Key) is on.

Door open.

Trunk open.

Reservation Mode not set. (Manual transmission vehicles only.)

If there is a problem remote starting your vehicle, you will hear three chirps from the remote to indicate that there is a problem. If you go to the vehicle and try again, an error code will be displayed through the parking lights. The lights will flash three times, pause, and then flash a number of times equivalent to the error code number. Example for error code 4, the parking lights will flash three times, pause, and then flash four times.

Examination of Remote Wakeup Failure

After Reservation Mode has been set up, it will be cancelled if either the trunk or a

door is opened.

After driving and removing Key, the engine will stay running for 2 minutes. If but

ton

is pressed for more than 2 sec. during this time, Reservation Mode will be

cancelled.

If Valet Mode is ON, Reservation Mode will be cancelled.

Remote Wakeup Reservation

On the slopes, a car may move. You should not set up the reservation mode.

Reservation Mode Cancellation in Manual Transmission Vehicles

Page 21

Two-Way Remote User’s Guide

Controlling Shock Sensor Sensitivity

To adjust the shock sensor sensitivity, locate the shock sensor and adjust the dial on the sensor. The higher the number on the dial, the higher the sensitivity of the sensor.

Shock Sensor sensitivity can vary from vehicle to vehicle for many reasons including where and how it is mounted, and the size of the vehicle. Some after install adjustment may be necessary to fine tune the sensor.

Control of Siren Sound

In order to increase the volume of the siren, locate the siren, (usually under the hood in the engine bay) and cut the loop of black wire at the base of the siren. Be careful not to cut the thicker black ground wire of the siren.

If the remote has been lost or damaged, you can enter Valet Mode using the ignition key of the vehicle. The following steps must be complet ed within a limited amount of time, so pl ease read through the instructions before beginning.

1) Turn the key to the

Ignition On position. When the ignition

is on, the lights in the instrument cluster will turn on. In most vehicles this position is two clicks forward from the

Off

position.

2)Move the key back one click

to the

Accessory On

posi

tion.

The lights in the instrument cluster should turn off.

3) Steps 1 and 2 must be repeated for a total of three times within

three seconds. Once this has been done, the alarm will turn off and valet mode will be active

Setting the Shock Sensor Sensitivity

The higher the numbers,

the more sensitive

Valet Mode can only be turned off through the remote

(Press buttons

III

for 0.5 sec. at the same time, the siren will chirp and the

parking lights will flash twice.)

Setup of Remote Options

To exit the remote programming menu, press buttons

+ IIIfor more than 2 sec.

The remote will automatically exit the programming menu if 15 sec. pass without a

button being pressed.

[ ]

Entering the Main Menu

The rem ote can be p rogra mmed after press ing buttons

III for

more than 2 sec. at the same time.

Button Control Method

Menu End Method

The icon corresponding to the option you are changing will flash on the screen.

Note

Function(Menu)

Set-up of present time

Set-up of timer start

reservation time

hour control

minute control

change(basic :

cancellation)

change(basic :

Activation)

change(basic :

cancellation)

change

(basic : “ ”)

The change of

Set-up of alarm clock time

Set-up /cancellation of

alarm clock function

Set-up/cancellation RPS

Set-up/cancellation of

vibration mode

Change of the temperature unit

Button

III

back to the previous menu

back to the next menu

Entering Valet Mode Using a Key

Page 22

Two-Way Remote User’s Guide

Function

Button

Application Method

Set-up of Alarm Clock Time

Set-up/cancellation of Alarm Clock Function

Set-up of Timer Start Reservation Time

Set-up/cancellation of Remote Paging Sensor

Set-up/cancellation of Vibration Mode

Fahrenheit Centigrade

ON/OFF

Change

ON/OFF

Hour

Minute

Hour

Minute

Hour

Minute

The icon flashes.

The icon,

and [ ] flash

The [ ], and

icon flash.

[ ] icon flashes

Set-up of Present time

At this time, button will control the hour, and button will control the minute.

Clock display

for alarm clock active, for alarm clock disabled. Toggle this option on and off with button .

[ ] icon flashes

When the alarm clock activates at the specified time, tap any button for 0.5 sec. to silence the remote.

In order for someone to use the RPS to page your remote, the system must be armed/locked and the RPS must be knocked on twice within 2 sec.

With the vibration function on, the remote will not make any sound unless the alarm is triggered. With vibration mode off, vibration will be felt during an RPS page, or if alarm is triggered.

The icon flashes. The change of the temperature unit with either

Clock display

for alarm clock active, for alarm clock disabled. Toggle this option on and off with button .

RPS Function ON/OFF

[ ] icon flashes

Clock display for alarm clock active, for alarm clock disabled. Toggle this option on and off with button .

Vibration Function ON/OFF

Page 23

Two-Way Remote User’s Guide

Magicar m110as bruger User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual