MADIC ITALIA GTV222A User Manual

Mod.N:Q060R06

User Manual
Revision R01-07
P/N: MAEU025

BV1000GTV

ALL-IN-ONE UNATTENDED PAYMENT

SYSTEM

MADIC ITALIA

Mod.N: Q060R06

2/26

1 INDEX

BV1000GTV...............................................................................................................................1

1 INDEX ...................................................................................................................................2

2 FIGURE INDEX .........................................................................................................................2

3 SAFETY INFORMATIONS AND INSTRUCTIONS ..................................................................................3

3.1 GENERAL SAFETY INFORMATION ...........................................................................................3

3.2 BASIC RULES .....................................................................................................................3

3.3 SAFETY COMPLIANCE ..........................................................................................................3

4 DECLARATION OF CON FORMITY ..................................................................................................4

4.1 WARNINGS .......................................................................................................................5

4.2 BV1000GTV ENVIRONMENT CONFORMITY ...............................................................................6

4.3 USA RADIO APPROVAL FEDERAL COMMUNICATIONS COMMISSION (FCC) ........................................7

4.4 CANADA RADIO APPROVAL (IC) .............................................................................................8

4.5 LASER SAFETY CONSIDERATION .............................................................................................9

5 WARRANTY CONDITIONS ......................................................................................................... 10

6 SECURITY ADVICE ................................................................................................................... 11

6.1 INTEGRITY CONTROL UPON RECEPTION................................................................................. 11

6.2 PIN ENTRY PROTECTION .................................................................................................... 11

7 VIEW AND ORDER CODES ......................................................................................................... 12

8 OVERVIEW ........................................................................................................................... 13

9 PACKAGING LIST .................................................................................................................... 13

10 TECHNICAL SPECIFICATIONS .................................................................................................... 14

10.1 TECHNICAL SPECIFICATIONS BV1000GTV.............................................................................. 14

10.2 BV1000GTV SPECIFICATIONS ............................................................................................. 15

10.3 BV1000GTV FRONT VIEW ................................................................................................. 16

10.4 BV1000GTV REAR VIEW ................................................................................................... 17

10.4.1 CONNECTORS PINOUT ............................................................................................... 19

11 CABLES .............................................................................................................................. 20

11.1 POWER CABLE ............................................................................................................... 20

11.2 S1 SERIAL CABLE ............................................................................................................ 20

11.3 CABLE FOR S2-S3 CONNECTION WITH A DB9 INTERFACE .......................................................... 21

12 MECHANICAL DIMENSIONS ..................................................................................................... 22

12.1 MECHANICAL DIMENSIONS BV1000GTV ............................................................................... 22

12.2 PANEL DRILLING BV1000GTV............................................................................................. 23

12.3 FIXING INDICATIONS FOR BV1000GTV ................................................................................. 24

12.4 INSTALLATION ADVICED ................................................................................................... 25

13 HOW TO CONTACT US ........................................................................................................... 26

2 FIGURE INDEX

FIGURE 1 – LASER CLASS LABEL ............................................................................................................................. 9

FIGURE 2 – Example of PIN entry protection ........................................................................................................ 11

FIGURE 3 – Product Overview BV1000GTV........................................................................................................... 12

FIGURE 4 –Front View BV1000GTV ...................................................................................................................... 16

FIGURE 5 – Rear view of BV1000GTV ................................................................................................................... 17

FIGURE 6 – Mechanical dimension of the BV1000GTV .......................................................................................... 22

FIGURE 7 – Panel drilling of BV1000GTV .............................................................................................................. 23

FIGURE 8 – Panel Fixing for BV1000GTV .............................................................................................................. 24

FIGURE 9 – ADA min and max heights of installation............................................................................................. 25

Globalcom Engineering

This document contains the proprietary information of Globalcom Engineering. Its receipt or possession does not convey any rights to
reproduce or disclose its contents or to manufacture, use or sell anything it may describe. Reproduction, disclosure or use without specific
written authorization of Globalcom Engineering is strictly forbidden. Mod.N:Q060R06

3/26

3 SAFETY INFORMATIONS AND INSTRUCTIONS

BV1000GTV is conform to the standard EN 62368-1+AC+A11 Electrical Safety of Data Processing Equipment
including Electrical Office Equipment.

3.1 GENERAL SAFETY INFORMATION

BV1000GTV has been designed and manufactured to meet international safety standard but, like any
electrical apparatus, due care must still be taken.

 Read and understand the instructions before using the equipment
 Not remove any screws to enter into area for non-operators
 Not allow liquid to spill into the internal cabinet side
 Not allow anything to rest on the power cord or telecomm cords and ensure a properly routing of

all the cable to prevent damage or accidental contact

 Not continue to operate with the equipment if you are in doubt about its normal working or if the

equipment has been damaged.

3.2 BASIC RULES

1) The responsibility of the safety for the sockets in the power circuits is of the customer

2) Verify that the power supply cable and the sockets are in good conditions

3) Don’t work in dangerous conditions when alone

4) If possible, connect and disconnect the signal cable at power off to avoid risk of shock caused by

possible contact of two equipment at different electrical potential.

5) The client must install a lighting protection if the zone is subject to thunderstorm or overvoltage.

3.3 SAFETY COMPLIANCE

In order to fulfill the safety standard EN 62368-1, BV1000GTV must be powered by a PS2 Limited Power
Source.

MADIC ITALIA

Mod.N: Q060R06

4/26

4 DECLARATION OF CONFORMITY

MADIC ITALIA declares that the payment system BV1000GTV, whose characteristics are described in this
manual, is conform to all relevant essential requirements on radio equipment and telecommunications
terminal equipment RED Directive 2014/53/EU, EMC Directive 2014/30/EU and ROHS directive
2011/65/EU amended 2015/863/EU.

The following standards and essential test suites published in the “Official Journal” of the European

communities, have been used to demonstrate the conformity of the product:

EN ETSI 301 489-3 Electro Magnetic Compatibility (EMC) standard for radio equipment and services; Part
3: Specific conditions for Short-Range Devices (SRD) operating on frequencies between 9 kHz and 246
GHz; Harmonized Standard covering the essential requirements of article 3.1(b) of Directive 2014/53/EU
EN ETSI 301 489-1 Electro Magnetic Compatibility (EMC) standard for radio equipment and services; Part
1: Common technical requirements; Harmonized Standard covering the essential requirements of article

3.1(b) of Directive 2014/53/EU and the essential requirements of article 6 of Directive 2014/30/EU
ETSI EN 300 330-1 Electromagnetic compatibility and Radio Spectrum Matters (ERM); Short Range Devices
(SRD); Radio equipment in the frequency range 9 kHz to 25 MHz and inductive loop systems in the
frequency range 9 kHz to 30 MHz; Part 1: Technical characteristics and test methods
EN ETSI 300 330-2 Electromagnetic compatibility and Radio Spectrum Matters (ERM); Short Range Devices
(SRD); Radio equipment in the frequency range 9 kHz to 25 MHz and inductive loop systems in the
frequency range 9 kHz to 30 MHz; Part 2: Harmonized EN covering the essential requirements of article

3.2 of the R&TTE Directive
CEI EN 62311 Assessment of electronic and electrical equipment related to human exposure restrictions
for electromagnetic fields (0 Hz - 300 GHz)
EN 62368-1+AC+A11 – Audio/Video, Information and Communication Technology Equipment - Part 1:
Safety Requirements
EN 50581:2012 Technical documentation for the assessment of electrical and electronic products
with respect to the restriction of hazardous substances.

Compliance with these requirements shall be evidenced by the affixing of the CE on the product. The
company responsible for placing the product on the market:

MADIC ITALIA S.p.A.

Via Volta 39 21010 Cardano Al Campo (VA) Italy

MADIC ITALIA

Mod.N:Q060R06

5/26

4.1 WARNINGS

This appliance is marked according to the European directive 2012/19/EU on waste electrical and
electronic equipment (WEEE Directive).

The symbol of crossed out wheeled bin on the product indicates that this WEEE must not be
treated as unsorted municipal waste and must be collected separately.

To assure the correct disposal and recycle of this product contact your supplier.

The abandonment or inappropriate disposal of waste can cause harm to environment and harm to the
human health.
By ensuring the correct disposal of this product you will help prevent negative consequences for the
environment and human health, also you will contribute to the preservation of the natural resources. The
device contains lithium manganese dioxide coin cells. The battery must be disposed at the appropriate
collection point.

BV1000GTV is compliance with the Directive 2011/65/EU of the European Parliament of the Council of 8
June 2011 on the restriction of certain hazardous substances in electrical and electronic equipment (also
known as RoHS Recast or RoHS2 and its amendment 2015/863/EU).
Specifically, BV1000GTV do not contain the substances listed in the table below in concentration greater
than listed maximum value.

RESTRICTED SUBSTANCE

Maximum LIMIT (by weight in

homogenous material)

Lead

0.1% (1000 ppm)

Mercury

0.1% (1000 ppm)

Cadmium¹

0.01% (100 ppm)

Hexavalent Chromium

0.1% (1000 ppm)

Polybrominated Biphenyls (PBB)

0.1% (1000 ppm)

Polybrominated diphenyl ethers (PBDE)

0.1% (1000 ppm)

Bis(2-Ethylhexyl) phthalate (DEHP)

0.1% (1000 ppm)

Benzyl butyl phthalate (BBP)

0.1% (1000 ppm)

Dibutyl phthalate (DBP)

0.1% (1000 ppm)

Diisobutyl phthalate (DIBP)

0.1% (1000 ppm)

BV1000GTV complies with the intent of the US Dodd-Frank Act for conflict materials Tin, Tungsten,
Tantalum, and Gold. Components containing these conflict materials was identified and the supplier has
verified the origin from conflict free smelters.

The BV1000GTV complies with the EU Regulation (EC) No 1907/2006 "Registration, Evaluation,
Authorization and Restriction of Chemicals" REACH for Substances of Very High Concern (SVHC's).
SVHC's are not present in the BV1000GTV.

MADIC ITALIA

Mod.N: Q060R06

6/26

4.2 BV1000GTV ENVIRONMENT CONFORMITY

Climatic and Vibration tests:

CEI EN 60068-2-1 - Environmental Testing Part 2-1: Tests: - Test A: Cold
CEI EN 60068-2-2 - Environmental Testing Part 2-2: Tests: - Test B: Dry heat
CEI EN 60068-2-14 - Environmental Testing Part 2-14: Tests: - Test N: Change of temperature
CEI EN 60068-2-30 - Environmental Testing Part 2-30: Tests: - Test Db: Damp heat, cyclic (12h + 12h cycle)
CEI EN 60068-2-78 - Environmental Testing Part 2-78: Tests: - Test Cab: Damp heat, steady state
CEI EN 60068-2-6 - Environmental Testing Part 2-6: Tests: - Test Fc: Vibration (sinusoidal)

Salt Mist test:

CEI EN 60068-2-11 - Environmental Testing Part 2-11: Tests: - Test Ka: Salt mist

External Mechanical Impact test (IK09) and Drop test:

CEI EN 62262 - Degrees of protection by enclosures for equipment against external mechanical impact
(IK09)
CEI EN 60068-2-31 – Environmental testing - Part 2-31: Tests - Test Ec: Rough handling shocks, primarily
for equipment-type specimens
EN 60068-2-75 – Environmental Testing Part 2-31: Tests: Test Eh: Hammer test

Verification of Internal Protection Code (IP54):

EN 60529+A1+A2 - Degrees of protection provided by enclosures (IP54)

MADIC ITALIA

Mod.N:Q060R06

7/26

4.3 USA RADIO APPROVAL FEDERAL COMMUNICATIONS COMMISSION (FCC)

PRODUCT NAME: BV1000GTV
FCC ID: 2AKMT-GTV222A

FCC Rules: Code of Federal Regulations (CFR) no.47 Part 15 - Radio Frequency Devices

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.

Note: this equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction, may cause harmful
interference to radio communications. However, there is no guarantee that the interference will not occur
in a particular installation. If this equipment causes harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measure:

 Reorient or relocate the receiving antenna
 Increase the separation between the equipment and the receiver.
 Connect the equipment into an outlet on a circuit different from that of the receiver.
 Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications made to the equipment not expressly approved by MADIC ITALIA S.P.A. may void
the FCC authorization to operate this equipment.

MADIC ITALIA

Mod.N: Q060R06

8/26

4.4 CANADA RADIO APPROVAL (IC)

IC: 22928-GTV222A

Innovation, Science and Economic Development Canada ICES-003 Compliance Label:

CAN ICES-3 (B)/NMB-3(B)

This device contains Iicence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and
Economic
Development Canada's Iicence-exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired

operation of the device.

Changes or modifications made to the equipment not expressly approved by MADIC ITALIA S.P.A. may void
the IC authorization to operate this equipment.