MadgeTech Temp101, Temp100, Temp110, TempRetriever Product Information Card

Red 485
Dark Blue Pantone 289
Light Blue 58% of Pantone 289

Red 485
Dark Blue Pantone 289
Light Blue 58% of Pantone 289

Product Quick Reference Card

Device Maintenance

Battery Replacement

Materials: Small Phillips Head Screwdriver and LTC-7PN battery

Temp101 and Temp110:

- Puncture the center of the back label with the screw driver
and unscrew the enclosure.

- Remove the battery by pulling it perpendicular to the board.

- Insert the new battery into the terminals and verify it is secure.

- Screw the enclosure back together securely.

Temp100 and TempRetriever:

- Puncture the center of the back label with the screw driver
and unscrew the enclosure.

- Use a small non-metallic device to push the coin-cell battery
out of its holder.

- Hold down the pushbutton in the middle of the circuit board
and insert the new battery into the holder.

- Release the pushbutton and watch to verify that the LED’s
blink. (If they do not, then you may have inserted the battery
upside down. Remove the battery and try again.)

- Replace the circuit board in the enclosure.

- Screw the enclosure back together securely.

Battery Warning

WARNING: FIRE, EXPLOSION, AND SEVERE BURN HAZARD. DO NOT
SHORT CIRCUIT, CHARGE, FORCE OVER DISCHARGE, DISASSEMBLE,
CRUSH, PENETRATE OR INCINERATE. BATTERY MAY LEAK OR
EXPLODE IF HEATED ABOVE 80°C (176°F).

Recalibration

Standard calibration is one point at 25°C for all 4 devices.

Pricing:

Recalibration traceable to NIST $60.00
Recalibration $40.00

Additional:

As Found Data $15.00 per parameter/channel
Verification Point $15.00 per point

To send the devices back, visit www.madgetech.com, select
Services then RMA Process.

Part Number Temp100 Temp101 Temp110 TempRetriever

Sensor Internal semiconductor

Range –40 to +80°C

Resolution 0.1°C

Accuracy +0.5°C (0 to +50°C)

Memory 32,767 32,767 32,767 16,383

Sample Rate 2 seconds up to

LED Indicator Red & Green Red Red Red & Green

Pushbutton Start Yes No No Yes

Alarm Yes Yes No Yes

Req. Interface Package IFC110 or IFC200

Baud Rate 2,400 2,400 57,600 38,400

Battery Life 1 year 1 year 10 years 1 year

Operating Environment –40 to +80°C, 0 to 95%RH non–condensing

Material ABS plastic

Dimensions 1.4” x 2.2” x 0.6”

Approvals CE

12 hours

(36mm x 56mm x

16mm)

2 seconds up to

12 hours

1.4” x 2.2” x 0.6”

(36mm x 56mm x

16mm)

2 seconds up to

12 hours

1.7” x 2.3” x 0.8”

(44mm x 59mm x

21mm)

Specifications subject to change.

See MadgeTech’s terms and conditions at www.madgetech.com

MadgeTech, Inc.

PO Box 50

Phone [phone]

www.madgetech.com

l

Warner, NH 03278

l

Fax [phone]

l

[e-mail]

5 seconds up to

30 minutes

1.4” x 2.2” x 0.6”

(36mm x 56mm x

16mm)

REV F 2009.04.30

Product Information Card

Temp100, Temp101, Temp110 and

TempRetriever

Temp100

Miniature Temperature Recorder with PushButton Start/Stop

Temp101

Miniature Temperature Recorder

Temp110

Miniature Temperature Recorder with 10 Year Battery Life

TempRetriever

Miniature Temperature Recorder with PushButton Start/Stop

To view the full MadgeTech product line,

visit our website at www.madgetech.com.

Temp100, Temp101, Temp110 and TempRetriever

Product Notes

Installation Guide

Product Quick Reference Card

Device Operation

Manual Start

When the Manual Start method is selected, the data logger
will be armed, but not recording. To start the device, hold the
push button down until both the green and red LEDs flash
momentarily.

LEDs

Once started, the LED will flash at the selected reading rate to
indicate that the device is running. The LED will flash in one
second intervals if there is an alarm condition.

If the device has two LEDs, the green LED will blink at the
specified reading rate. The red LED will blink if the alarm has
been breeched.

Alarm Settings

To change the settings for the temperature alarm;

- Select Alarm Settings from the Device menu in the MadgeTech
software. A window will appear allowing the customer to set the
high and low temperature alarms.

- Press Change to edit the values.

- Check Enable Alarm Settings to enable the feature. The values
can be entered in the field manually or by using the scroll bars.

- Click Save to save the changes. To clean an active alarm, press

Clear Alarm.

Installing the Interface cable

- IFC200, IFC202 or IFC300
Refer to the “Quick Start Guide” included in the package.

- IFC110, IFC102 or IFC103
Plug the serial cable into the port and verify it is secure.

- USB-1 or USB-101
Install the USB drivers from the CD provided in the kit, than

plug the USB cable into the computer and the serial cable into
the serial port.

Installing the software

Insert the Software CD in the CD-ROM Drive. If the autorun
does not appear, locate the drive on the computer and double
click on Autorun.exe. Follow the instructions provided in the
Wizard.

Connecting the data logger

- Once the software is installed and running, plug the interface
cable into the data logger.

- Click the Communication Menu, then Auto Configure Port.

- After a moment, a box similar to the following will appear;

Starting the data logger

- Click Device Menu then
Start Device.

- Choose the desired start
method.

- Choose the start parameters
by selecting a Reading Rate
suitable for your application.

- Enter in any other desired
parameters and click Start.

- A box will appear stating the
data logger has been started.
Click OK.

- Disconnect the data logger from the interface cable and
place it in the environment to measure.

Note: The device will stop recording data when the end of
memory is reached or the device is stopped. At this point the
device cannot be restarted until it has been re-armed by the
computer.

Downloading data from a data logger

- Connect the data logger to the interface cable.

- Click the Device Menu then Read Device Data. This will
offload all recorded data onto the PC.

- Click OK. The Device Status box will appear. Click OK.

- At this point, communications have been configured for your
logger. These settings can be found under the Communication
Menu.

Note: For additional installation instructions refer to your “Data
Logger & Software Operating Manual”.

Technical Support

Visit www.madgetech.com, or call [phone].
Technical support is also available by e-mailing
[e-mail]

Additional product information is available by e-mailing
[e-mail].