MadgeTech Temp1000Ex-1-KR, Temp1000Ex-5.25-KR, Temp1000Ex-7, Temp1000Ex-1, Temp1000Ex-2-KR User manual

Temp1000Ex

Intrinsically Safe Temperature
Data Logger

PRODUCT
USER GUIDE

TABLE OF CONTENTS

2 Product Overview

2 Installation Guide

2 Device Operation

3 Device Maintenance

4 Appendix A

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Temp1000Ex

PRODUCT USER GUIDE

Product Overview

The Temp1000Ex carries hazardous location, intrinsically
safe certification in accordance with the latest issue of:
IEC 60079-0, IEC 60079-11
Directive 2014/34/EU (known as ATEX)

Certified Intrinsically Safe for:

• Electrical Protection Concepts: IEC: 60079-11 Ex ia – Ex
ic, Intrinsic Safety Zones 0-2

• Equipment Protection Level: Ga – Gc, Zones 0-2

• Gas Groups: IIC

• Temperature Class: T4

Operational Warnings

• When used in hazardous locations, the Temp1000Ex is to
be installed prior to the location becoming hazardous
and removed only after the area is no longer hazardous.

• The maximum allowed ambient temperature for the
Temp1000Ex (under any circumstances) is 80 °C. The
minimum rated operating temperature is -40 °C.

• The Temp1000Ex is approved for use only with the
Tadiran TL-2150/S battery. Replacement with any other
battery will void the safety rating.

Installation Guide

Installing the Software

The Software can be downloaded from the MadgeTech
. Follow the instructions

provided in the Installation Wizard.

Installing the USB Interface Drivers

IFC400 or IFC406 — Follow the instructions provided in

the Installation Wizard to install the USB Interface Drivers.
Drivers can also be downloaded from the MadgeTech
website at madgetech.com.

Device Operation

Connecting and Starting the Data Logger

1. Once the software is installed and running, plug the
interface cable into the docking station (IFC400 or
IFC406).

2. Connect the USB end of the interface cable into an
open USB port on the computer.

3. Place the data logger into the docking station (IFC400
or IFC406).

• Batteries are user replaceable, but are to be removed or
replaced only in locations known to be non-hazardous.

• Tampering or replacement of non-factory components
may adversely affect the safe use of the product, and is
prohibited. Except for replacement of the battery, the
user may not service the Temp1000Ex. MadgeTech, Inc.
or an authorized representative must perform all other
service to the product.

Ordering Information

• 902153-00 — Temp1000Ex-2 (2 inch Probe)

• 902155-00 — Temp1000Ex-1 (1 inch Probe)

• 902156-00 — Temp1000Ex-5.25 (5.25 inch Probe)

• 902157-00 — Temp1000Ex-7 (7 inch Probe)

Key Ring End Cap

• 902209-00 — Temp1000Ex-1-KR (1 inch Probe)

• 902210-00 — Temp1000Ex-2-KR (2 inch Probe)

• 902211-00 — Temp1000Ex-5.25-KR (5.25 inch Probe)

• 902212-00 — Temp1000Ex-7-KR (7 inch Probe)

Accessories

• 900319-00 — IFC400

• 900325-00 — IFC406

• 901745-00 — Battery Tadiran TL-2150/S

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

4. The data logger will automatically appear under
Connected Devices within the software.

5. For most applications, select Custom Start from
the menu bar and choose the desired start method,
reading rate and other parameters appropriate for the
data logging application and click Start. (Quick Start

applies the most recent custom start options, Batch
Start is used for managing multiple loggers at once,
Real Time Start stores the dataset as it records while

connected to the logger.)

6. The status of the device will change to Running or
Waiting to Start, depending upon your start method.

7. Disconnect the data logger from the interface cable
and place it in the environment to measure.

Note: The device will stop recording data when the end of memory is
reached or the device is stopped, unless user selectable memory wrap
is enabled. At this point the device cannot be restarted until it has been
re-armed by the computer.

Product User Guide | 2

Temp1000Ex

PRODUCT USER GUIDE

Device Operation (cont’d)

Downloading Data from a Data Logger

1. Place the logger into the docking station (IFC400 or
IFC406).

2. Highlight the data logger in the Connected Devices
list. Click Stop on the menu bar.

3. Once the data logger is stopped, with the logger
highlighted, click Download.

4. Downloading will offload and save all the recorded
data to the PC.

Device Maintenance

Battery Replacement

Materials: Replacement Battery (Tadiran TL-2150/S)

1. Move device to a non-hazardous location before

replacing battery.

2. Observe Operational Warnings when removing and

replacing the battery.

O-Rings

O-ring maintenance is a key factor when properly
caring for the Temp1000Ex. The O-rings ensure a tight
seal and prevent liquid from entering the inside of the
device. Please refer to the application note “O-Rings 101:
Protecting Your Data”, found at madgetech.com, for
information on how to prevent O-ring failure.

Recalibration

Additional Services:

Custom calibration and verification point options
available, please call for pricing.

Call for custom calibration options to accommodate specific application needs.
Prices and specifications subject to change. See MadgeTech’s terms and conditions

To send devices to MadgeTech for calibration, service or repair, please use the

3. Unscrew the bottom of the data logger and remove the
battery.

4. Place the new battery into the logger. Caution: Observe

correct battery polarity when installing.

5. Screw the cover onto the data logger.

Communication

To ensure desired operation of the TEMP1000Ex, please keep the surface clear of any foreign objects or
substances. The TEMP1000Ex’s data is downloaded through external contact with the IFC400 or IFC406 docking

station. Covering the surface with foreign objects (i.e. Calibration Labels) can prevent the communication and/
or downloading process.

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

DOC-1367036-00 REV 5 2020.11.30

Temp1000Ex

APPENDIX A

The name and address of the manufacturer:
MadgeTech, Inc.
6 Warner Road
Warner, NH 03278 USA

Product model and description:

902153-00 - Temp1000EX-2
902154-00 - RHTemp1000EX
902155-00 - Temp1000EX-1
902156-00 - Temp1000EX-5.25
902157-00 - Temp1000EX-7

This product conforms with the following Union harmonization legislation:
2014/34/EU – ATEX Directive

The following harmonized standards and other technical specification were used in support of the declaration:
Harmonized Standards: EN 60079 - 0 Edition 2018
EN 60079 -11 Edition 2012

Notified body SGS Fimko Oy, number 0598 performed EU-Type examination in accordance with Annex III of the directive and
issued the certificate: Baseefa19ATEX0126

Notified body SGS Fimko Oy, number 0598 performed Conformity to type based on quality assurance of the production
process in accordance with Annex IV of the directive and issued the QA Notification document: Baseefa19ATEX0126

Additionally, product complies with the essential requirements, and carries the CE marking accordingly with:
2014/30/EU – EMC Directive
2015/863/EU – RoHS3 Directive
1907/2006/EU – REACH Directive

And conforms with the following product standards and/or normative documents:

IEC 61326-1 Edition 2013

Emission Requirements
CISPR 11, Radiated Emissions, 30 MHz to 1 GHz
Limit: CISPR 11, Group 1, Class A
Limit: FCC Class A

Enclosure Port

IEC 61000-4-2, Electrostatic Discharge
Level: 4 kV Contact, 8 kV Air Discharges

IEC 61000-4-3, Radiated Immunity (EM Field)
Level: 10 V/M, 80 to 1000 MHz
3 V/M, 1.4 to 2.0 GHz
1 V/M, 2.0 to 2.7 GHz

Supplementary Information:

The products were tested in a typical usage configuration.
RoHS Exemptions applied 6(a)), 7(c)-II

Declared on behalf of MadgeTech, Inc.

EU Declaration of Conformity

No. DC-2020-250

According to EN ISO/IEC 17050-1:2004

902208-00 - RHTemp1000EX-KR
902209-00 - Temp1000EX-1-KR
902210-00 - Temp1000EX-2-KR
902211-00 - Temp1000EX-5.25-KR
902212-00 - Temp1000EX-7-KR

Dianne Moulton, Quality Manager
Issued from MadgeTech, Inc. Warner, NH USA November 25, 2020

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Certificate Number

Certificate Number:

Product

:

Manufacturer:

Address:

having any variations specified in the Schedule attached to this certificate and the documents therein referred to

.

potentially explosive atmospheres given in Annex II to the Directive.

Body 0598). The original certificate number is retained.

The examination and test results are recorded in confidential Report No.

Compliance wit

h the Essential Health and Safety Requirements has been assured by compliance with:

except in respect of those requirements listed at item 18 of the Schedule.

of Use specified in the schedule to this certificate.

are not covered by this certificate.

The marking of the product shall include the following :







SGS

Fimko Oy

Customer Reference No.

Project File No.

falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent

of the law.

Authorised Signatory for SGS Fimko Oy

Baseefa19ATEX0126

Issue 2

Issued 12 November 2020

Page 1 of 4

1

EU - TYPE EXAMINATION CERTIFICATE

2 Equipment or Protective System Intended for use in Potentially Explosive Atmospheres

Directive 2014/34/EU

3 EU - Type Examination

4

5

6

Baseefa19ATEX0126 – Issue 2

RHTEMP1000EX and TEMP1000EX

MadgeTech, Inc

6 Warner Road, Warner, NH 03278, USA

7 This re-issued certificate extends EU Type Examination Certificate No. Baseefa19ATEX0126 to apply to product

designed and constructed in accordance with the specification set out in the Schedule of the said certificate but

8 SGS Fimko Oy, Notified Body number 0598, in accordance with Article 17 of Directive 2014/34/EU of the European

Parliament and of the Council, dated 26 February 2014, certifies that this product has been found to comply with the
Essential Health and Safety Requirements relating to the design and construction of products intended for use in

8.1 The original certificate was issued by SGS Baseefa Ltd (UK Notified Body 1180). It, and any supplements
previously issued by SGS Baseefa Ltd have been transferred to the supervision of SGS Fimko Oy (EU Notified

See Certificate History

9

EN IEC 60079-0: 2018 EN 60079-11: 2012

10 If the sign “X” is placed after the certificate number, it indicates that the product is subject to the Specific Conditions

11 This EU - TYPE EXAMINATION CERTIFICATE relates only to the design and construction of the specified

product. Further requirements of the Directive apply to the manufacturing process and supply of this product. These

12

II 1 G Ex ia IIC T4 Ga (-40°C ≤ Ta ≤ +80°C)



8001

This document is issued by the Company subject to their General Conditions for Certification Services accessible at

http://www.sgs.com/en/Terms-and-Conditions.aspx . Attention is drawn to the limitation of liability, indemnification and jurisdiction

issues defined therein. Any holder of this document is advised that information contained herein reflects the Company’s findings at the
time of their intervention only and within the limits of Client’s instructions, if any. It does not necessarily indicate that the equipment may
be used in particular industries or circumstances. The Company’s sole responsibility is to its Client and this document does not exonerate
parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be
reproduced except in full, schedule included, without prior written approval of the Company. Any unauthorized alteration, forgery or

20/0489

SGS Fimko Oy

Takomotie 8

FI-00380 Helsinki, Finland

Telephone [phone]

e-mail [e-mail]

web site www.sgs.fi

Business ID 0978538-5 Member of the SGS Group (SGA SA)

BAS-CERT-084 SGS Baseefa Limited is an associate of SGS Fimko OY Issue 2

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

R S SINCLAIR

Certificate Number

Schedule

DATA LOGGER

Baseefa19ATEX0126

Issue 2

13

Issued 12 November 2020

Page 2 of 4

14

15 Description of Product

The product is a temperature sensor TEMP1000EX and temperature with humidity sensor RHTEMP1000EX with additional
model variants. These dataloggers are to monitor temperature and humidity for intended area of deployment. The data logging
stops once the maximum memory capacity is reached. This data is extracted by removing the product from the area of
deployment and putting it onto a docking station, through serial communication. Data recording will re-start only once reset
by the computer. The data is then collected. These sensors are designed to be intrinsically safe for temperature range of -40°C
< Tamb < 80°C. Equipment is designed for Zone 0, under EPL Ga for gas group IIC, classified under temperature code T4.
Humidity range for the product is from 0% to 100% on RH scale. Equipment is powered by one Tadiran TL 2150 1/2AA cell.
Product dimensions for TEMP Model Series is 2.65 in. X .97 in. dia., with various lengths of probe attachments based on
utilization. And, RHTEMP Model Series is 1.7 in. X 0.97 in. X 0.97 in. They appear alike and are cylindrical portable sensors,
with probe attachments, which is the difference in the Model Series. In addition, there is mechanical key ring feature provided
on enclosure for aesthetic looks only. This design does not relate to safety or protection type of the product.

16 Report Number

See Certificate History

17 Specific Conditions of Use

None

18 Essential Health and Safety Requirements

In addition to the Essential Health and Safety Requirements (EHSRs) covered by the standards listed at item 9, the following
are considered relevant to this product, and conformity is demonstrated in the report:

Certificate Number Baseefa19ATEX0126 – Issue 2

Clause Subject

1.4.1 External effects

1.4.2 Aggressive substances, etc.

19 Drawings and Documents

New drawings submitted for this issue of certificate:

Number Sheet Issue Date Description

DOC-902154-00 1 of 1 1.3 11/4/2020

DOC-902155-00 1 of 1 1.3 11/4/2020 TEMP100EX TEMPERATURE DATA LOGGER

SUB-1367007-XX 1 of 3 1.1 9/29/2020 TEMP1000EX-XX ELECTRICAL ASSEMBLY

SUB-1367007-01 1 of 3 1.1 11/5/2020 TEMP1000EX-1 ELECTRICAL ASSEMBLY

SUB-1368007-00 1 of 3 1.1 11/5/2020 RHTEMP1000EX ELECTRICAL ASSEMBLY

The above drawings are associated and held with IECEx Certificate No. IECEx BAS 19.0109 Iss. 2

BAS-CERT-084 SGS Baseefa Limited is an associate of SGS Fimko OY Issue 2

RHTEMP100EX, TEMPERATURE AND HUMIDITY

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Certificate Number

ASSEMBLY

PCB ASSEMBLY

SENSOR ADAPTER ASSEMBLY

ASSEMBLY

ASSEMBLY

DRAWING, 2

-

PIN BATTERY CONNECTION

BATTERY

CONNECTION

ADAPTER

AND FLEXIBLE PROBE ADAPTER

(RHI)

RELATIVE HUMIDITY SENSOR ADAPTER (RHi)

Baseefa19ATEX0126

Issue 2

Current drawings which remain unaffected by this issue:

Number Sheet Issue Date Description

SUB-2106007-02 1 of 1 1.1 11/22/2019 HITEMP140 & 1000Ex 2" PROBE BOARD SUB

SVC-2104007-00 1 of 1 1.1 11/22/2019 BOARD HT & 1000Ex 2-PIN BATTERY CONTACT

SVC-2105007-01 1 to 2 1.1 11/22/2019 1000EX PCB ASSEMBLY

SVC-2107007-01 1 of 1 1.1 11/22/2019 PCB ASSEMBLY, HITEMP140 & 1000EX RH

SUB-2106007-03 1 of 1 1.1 11/22/2019 HITEMP140 & 1000Ex 5.25" PROBE BOARD SUB

SUB-2106007-04 1 of 1 1.1 11/22/2019 HITEMP140 & 1000Ex 7" PROBE BOARD SUB

DOC-2104002-00 1 of 1 1.0 01/21/2019 HITEMP140 AND 1000EX SCHEMATIC

DOC-2104003-00 1 of 1 1.0 01/21/2019 PCB ASSEMBLY, HITEMP140 AND 1000EX 2-PIN

Issued 12 November 2020

Page 3 of 4

DOC-2105002-01 1 of 1 1.0 03/25/2019 SCHEMATIC DRAWING 1000EX PCB

DOC-2105003-01 1 of 1 1.0 05/30/2019 PCB ASSEMBLY, 1000EX

DOC-2106002-XX 1 of 1 1.0 05/31/2019 HITEMP140 AMD 1000EX SCHEMATIC

DRAWING, RIGID AND FLEXIBLE ROBE

DOC-2106003-XX 1 of 1 1.0 05/31/2019 PCB ASSEMBLY, HITEMP140 AND 1000EX RIGID

DOC-2107002-01 1 of 1 1.0 05/31/2019 HITEMP140 AND 1000EX RELATIVE HUMIDITY

SCHEMATIC DRAWING, SENSOR ADAPTER

DOC-2107003-01 1 of 1 1.0 05/31/2019 PCB ASSEMBLY, HITEMP140 AND 1000EX

The above drawings are associated and held with IECEx Certificate No. IECEx BAS 19.0109.

20 Certificate History

Certificate No. Date Comments

Baseefa19ATEX0126 19 December 2019 The release of the prime certificate. The associated test and

assessment against the requirements of EN IEC 60079-0: 2018 &
EN 60079-11: 2012 is documented in Certification Report No.
GB/BAS/ExTR19.0287/00 (held with IECEx BAS 19.0109 Iss. 0),
Project File No. 19/0594.

Baseefa19ATEX0126
Issue 1

27 July 2020 This issue of the certificate permits the addition of variants of the

equipment fitted with a key ring and other minor drawing changes
not affecting the original assessment.

The equipment description on page 2 of the certificate was updated
to include reference to these key ring variants.

No additional changes performed under this revision.

The associated test and assessment of the above is documented in
Certification Report No. GB/BAS/ExTR20.0079/00 (held with
IECEx BAS 19.0109 Iss. 1), Project File No. 20/0143.

BAS-CERT-084 SGS Baseefa Limited is an associate o f SGS Fimko OY Issue 2

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Certificate Number

SUB-1367006-03, SUB-1367006-04, SUB-1367006-K1,

Baseefa19ATEX0126

Issue 2

Certificate No. Date Comments

Baseefa19ATEX0126
Issue 2

For drawings applicable to each issue, see original of that issue.

11 November 2020 This issue of the certificate permit minor drawings changes not

affecting the previous assessment. As a result of these drawing
changes, drawing No’s 902153-00, 902154-00, 902155-00,
902156-00, 902157-00, SUB-1367006-01, SUB-1367006-02,

SUB-1367006-K2, SUB-1367006-K3, SUB-1367006-K4,
SUB-1368006-00, SUB-1368006-K0, SUB-2105007-01 &
SUB-2107007-00 now no longer require listing as controlled
drawings and were removed from the above drawing list.

The associated test and assessment of the above is documented in
Certification Report No. GB/BAS/ExTR20.0167/00 (held with
IECEx BAS 19.0109 Iss. 2), Project File No. 20/0489.

Issued 12 November 2020

Page 4 of 4

BAS-CERT-084 SGS Baseefa Limited is an associate of SGS Fimko OY Issue 2

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com