MadgeTech RFRHTemp101A Product Information Card

Red 485
Dark Blue Pantone 289
Light Blue 58% of Pantone 289

Red 485
Dark Blue Pantone 289
Light Blue 58% of Pantone 289

Product Quick Reference Card

Device Maintenance

Battery Replacement

Materials:

Small Phillips Head Screwdriver
Replacement Battery (LTC-7PN)

- Puncture the center of the back label with the screw driver
and unscrew the enclosure.

- Remove the battery by pulling it perpendicular to the circuit
board.

- Insert the new battery into the terminals and verify it is secure.

- Screw the enclosure back together securely.

Note: Be sure not to over tighten the screws or strip the threads.

Battery Warning

WARNING: FIRE, EXPLOSION, AND SEVERE BURN HAZARD. DO NOT
SHORT CIRCUIT, CHARGE, FORCE OVER DISCHARGE, DISASSEMBLE,
CRUSH, PENETRATE OR INCINERATE. BATTERY MAY LEAK OR
EXPLODE IF HEATED ABOVE 80°C (176°F).

Recalibration

The RFRHTemp101A standard calibration is one point at 25°C and
two points at 25%RH and 75%RH.

Pricing:

Recalibration traceable to NIST $90.00
Recalibration $70.00

Additional:

As Found Data $15.00
Additional Points $15.00 per point

To send the devices back, visit www.madgetech.com, select Services
then RMA Process.

Part Number RFRHTemp101A

Internal Temperature Sensor Internal Semiconductor

Internal Temperature Range -30 to +70°C

Internal Temperature Resolution 0.1°C

Internal Temperature Accuracy +0.5°C

RH Measurement Range 0 to 95%RH

RH Resolution 0.5%RH

RH Calibrated Accuracy +3%RH

Memory 5,461/channel

Reading Rate 30 seconds up to 12 hours

LED Red and Green

Required Interface Package RFC101A

PC Baud Rate 57,600

RF Carrier Frequency 418 + 0.075MHz

RF Baud Rate 4,800

RF Range Typical Outdoors/Line of Sight: Up to 120’ (36m)

Typical Battery Life 1 Year

Material ABS Plastic

Operating Environment -30 to +70°C, 0 to 95%RH (Non-Condensing)

Dimensions 1.7” x 2.3” x 0.8” plus 2.0” Antenna

Approvals US (FCC), CA (IC)

Typical Indoors/Urban: Up to 40’ (12m)

(43mm x 59mm x 21mm plus 51mm Antenna)

Specifications subject to change.

See MadgeTech’s terms and conditions at www.madgetech.com

Product Information Card

RFRHTemp101A

RFRHTemp101A

Temperature and Humidity Recorder and Wireless Transmitter

MadgeTech, Inc.

PO Box 50

Phone [phone]

www.madgetech.com

l

Warner, NH 03278

l

Fax [phone]

l

[e-mail]

To view the full MadgeTech product line,

visit our website at www.madgetech.com.

REV A 2008.07.08

RFRHTemp101A

Product Notes

Installation Guide

Product Quick Reference Card

Device Operation

LEDs

Once started, the green LED will blink at the specified reading
rate. The red LED will blink each time a reading is sent to the
receiver. The LED on the RFC101A receiver will blink when a
reading is received.

Alarm Settings

The wireless series does have alarm features. Refer to the
“Operations Manual for RF Series Data Loggers” located on the
software CD for a full list of instructions.

Installing the Interface cable

- IFC200, IFC202 or IFC300
Refer to the “Quick Start Guide” included in the package.

- IFC110, IFC102 or IFC103
Plug the serial cable into the port and verify it is secure.

- USB-1 or USB-101
Install the USB drivers from the CD provided in the kit, than

plug the USB cable into the computer and the serial cable into
the serial port.

Installing the software

Insert the Software CD in the CD-ROM Drive. If the autorun
does not appear, locate the drive on the computer and double
click on Autorun.exe. Follow the instructions provided in the
Wizard.

Connecting the data logger

- Once the software is installed and running, plug the interface
cable into the data logger.

- Click the Communication Menu, then Auto Configure Port.

- After a moment, a box similar to the following will appear;

- Click OK. The Device Status box will appear. Click OK.

- At this point, communications have been configured for your
logger. These settings can be found under the Communication
Menu.

Note: For additional installation instructions refer to your “Data
Logger & Software Operating Manual”.

Starting the data logger

- Click Device Menu then
Start Device.

- Choose the desired start
method.

- Choose the start parameters
by selecting a Reading Rate
suitable for your application.

- Enter in any other desired
parameters and click Start.

- A box will appear stating the
data logger has been started.
Click OK.

- Disconnect the data logger from the interface cable and
place it in the environment to measure.

- Plug in the RFC101A receiver. Disconnectinf the IFC110 is
necessary.

- Click the Communication Menu, Select Baud Rate. Select 4800
baud. This is the baud rate for the receiver.

- Data will now transmit back to the PC from the data logger.

Note: The device will stop recording data when the end of memory
is reached or the device is stopped. At this point the device cannot
be restarted until it has been re-armed by the computer.

Downloading data from a data logger

- Connect the data logger to the interface cable.

- Click the Device Menu then Read Device Data. This will
offload all recorded data onto the PC.

Technical Support

Visit www.madgetech.com, or call [phone].
Technical support is also available by e-mailing
[e-mail]

Additional product information is available by e-mailing
[e-mail].