RFC1000-IP69K
Splash-Proof Wireless Transceiver for the RFOT,
Therm•A•lert and RF2000A data loggers
Product User Guide
Find Quality Products Online at: sales@GlobalTestSupply.com
www.GlobalTestSupply.com
Product User Guide
Table of Contents
Product Overview .................................................... 3
Soware Installation ................................................ 4
Activating & Deploying the Data Logger ................. 4
Mounting Instructions .............................................. 5
Channel Programming ......................................... 6-7
Troubleshooting ...................................................... 8
Compliance Information .......................................... 9
General Specifications ........................................... 10
2
Find Quality Products Online at: sales@GlobalTestSupply.com
www.GlobalTestSupply.com
RFC1000-IP69K
Product Overview
For environments that require high pressure, high temperature washdown, MadgeTech has
designed the RFC1000-IP69K. This new splash-proof transceiver can be installed directly in the
wash down location, ensuring 100% communication throughout the entire process. This device
includes a high powered transceiver with an IP69K ingress protection rating. The RFC1000IP69K has a substantially longer transmit range, providing better performance in occluded
environments such as ovens, and refrigerators. This new The RFC1000-IP69K also includes an
external antenna which is protected by a neoprene boot, allowing more flexibility with mounting
positions in both orientation and proximity to metal walls.
Operating Environment
The RFC1000-IP69K is rated for use in an environment with temperatures from -20 °C to 85 °C
(-4 °F to 185 °F) and a humidity range of 0 %RH to 100 %RH. The device has been specifically
tested to ensure its ability to resist water ingress as well as dust. The RFC1000-IP69K will
withstand high pressure and high temperature wash down cycles using caustic chemicals, as
the enclosure is made of Acetal plastic.
Note: The power supply of the RFC1000-IP69K is not rated as splash-proof. Exposing the power
supply to moisture will potentially damage the unit. Additional precautions should be taken
by the user if the power supply will be exposed to a condensing environment.
LED Indicators
» Power (Red): Indicates that the device has power.
» Data (Green): Blinks when communicating with other MadgeTech devices.
Wireless Transmission
The RFC1000-IP69K can connect to a maximum of 64 data loggers. The RFC1000-IP69K
transmits on a frequency of 2.405 GHz - 2.475 GHz.
Transmission distance to data logger:
» Unobstructed line-of-sight (outdoors): Up to 2,000 feet maximum
» Typical urban environment (indoors): Up to 500 feet maximum
Transmission distance to other RFC1000-IP69K wireless transceiver:
» Unobstructed line-of-sight (outdoors): Up to 4,000 feet maximum
» Typical urban environment (indoors): Up to 1,000 feet maximum
Extending Wireless Transmission Distance
Additional RFC1000 wireless transceivers (sold separately) can be used as repeaters to
transmit over greater distances. If transmitting over a distance greater than 1,000 feet indoors,
4,000 feet outdoors or there are walls, obstacles or corners that need to be maneuvered
around, set up additional RFC1000’s as needed. Plug each one into an electrical outlet in the
desired locations.
3
Find Quality Products Online at: sales@GlobalTestSupply.com
www.GlobalTestSupply.com
Product User Guide
Software Installation
MadgeTech 4 Soware
The MadgeTech 4 Soware makes the process of downloading and reviewing
data quick and easy, and is free to download
Installing the MadgeTech 4 Soware
1. Download the MadgeTech 4 Soware on a Windows PC by going to:
2. Locate and unzip the downloaded file (typically you can do this by right clicking on the file
and selecting Extract).
3. Open the MTInstaller.exe file.
4. You will be prompted to select a language, then follow the instructions provided in the
MadgeTech 4 Setup Wizard to finish the MadgeTech 4 Soware installation.
Installing the USB Interface Driver
USB Interface Drivers can easily be installed on a Windows PC, if they are not already available
and running.
1. Download the USB Interface Driver on a Windows PC by going to:
2. Locate and unzip the downloaded file (typically you can do this by right clicking on the file
and selecting Extract).
3. Open the PreInstaller.exe file.
4. Select Install on the dialog box.
Activating & Deploying the Data Logger
1. Connect an RFC1000-IP69K wireless transceiver to the Windows PC with the provided USB cable.
2. Additional RFC1000’s can be used as repeaters to transmit over greater distances. Plug each one
into an electrical outlet in the desired locations.
3. Verify that the data loggers (sold separately) are in wireless transmission mode.
4. On the Windows PC, launch the MadgeTech 4 Soware.
5. All active data loggers will be listed in the Device tab within the Connected Devices panel.
6. To claim a data logger, select the desired data logger in the list and click the Claim icon.
7. Once the data logger has been claimed, select a start method in the Device tab.
For steps to claim the data logger and view data using MadgeTech Cloud
Services, refer to the MadgeTech Cloud Services Soware Manual at:
4
Find Quality Products Online at: sales@GlobalTestSupply.com
www.GlobalTestSupply.com
RFC1000-IP69K
Mounting Instructions
The RFC1000-IP69K has a pivoting external antenna to accommodate either tabletop or wall
mounted orientation. For best wireless performance, RFC1000-IP69K wireless transceivers and
the MadgeTech data loggers should be mounted in the same orientation. This usually means
that the external antenna will be pointing straight up. The antenna of the RFC1000-IP69K
should also be at least 1.5 inches away from any metal.
5
Find Quality Products Online at: sales@GlobalTestSupply.com
www.GlobalTestSupply.com
Product User Guide
Channel Programming
Dierent wireless channels may be used to create multiple networks in one area, or to
avoid wireless interference from other devices. Any RFC1000-IP69K wireless transceiver or
MadgeTech data logger on the same network is required to use the same channel. If all of the
devices are not on the same channel, the devices will not communicate with one another.
The RFC1000-IP69K is programmed by default on channel 25.
CHANNEL NOTE: MadgeTech wireless data loggers and RFC1000 wireless transceivers purchased
prior to April 15, 2016 are programmed by default to channel 11. Please refer to the Product User
Guide provided with these devices for instructions to change the channel selection if needed.
Configuring the Channel Settings of the RFC1000-IP69K
1. Unplug the RFC1000-IP69K.
2. Use a Phillips head screwdriver to unscrew the back of the RFC1000-IP69K enclosure.
3. Find the DIP switches located on the front of the PCB circuit board (diagram 1a).
4. Change the DIP switches to match the desired channel (diagram 1b).
5. Screw the RFC1000-IP69K enclosure back together.
6. Reconnect the RFC1000-IP69K.
DIP Switches
1a.
6
Find Quality Products Online at: sales@GlobalTestSupply.com
www.GlobalTestSupply.com
RFC1000-IP69K
Channel DIP Switch Orientation
The images below show the orientations available of the switches for each channel.
1b.
CH 11
CH 12
CH 13
CH 14
CH 15
CH 16
CH 17
CH 23
CH 18
CH 24
CH 19
CH 25
NOT SUPPORTEDDEFAULT CHANNEL
CH 20
CH 26
CH 21
CH 22
7
Find Quality Products Online at: sales@GlobalTestSupply.com
www.GlobalTestSupply.com
Product User Guide
Troubleshooting
Troubleshooting Wireless Transceiver Problems
Check that the soware properly recognizes the connected RFC1000-IP69K wireless transceiver.
If the wireless data logger is not appearing in the Connected Devices list, it may be that the
RFC1000-IP69K is not properly connected.
1. In the MadgeTech 4 Soware, click the File button, then click Options.
2. In the Options window, click Communications.
3. The Detected Interfaces box will list all of the available communication interfaces. If the RFC1000-
IP69K is listed here, then the soware has correctly recognized and is ready to use it.
Check that Windows recognizes the connected RFC1000-IP69K wireless transceiver.
If the soware does not recognize the RFC1000-IP69K, there may be a problem with Windows or the
USB drivers.
1. In Windows, click Start, right-click Computer and choose Properties.
2. Select Device Manager in the le hand column.
3. Double-click on Universal Serial Bus Controllers.
4. Look for an entry for Data Logger Interface.
5. If the entry is present, and there are no warning messages or icons, then windows has correctly
recognized the connected RFC1000-IP69K.
6. If the entry is not present, or has an exclamation point icon next to it, the USB drivers may need
to be installed. These are available on the soware flash drive included with the RFC1000-IP69K,
Ensure that the USB end of the RFC1000-IP69K is securely connected to the computer.
1. Locate the USB-A plug of the RFC1000-IP69K.
2. If the cable is connected to the PC, unplug it and wait ten seconds.
3. Reconnect the cable to the PC.
4. Check to make sure that the red LED is lit, indicating a successful connection.
8
Find Quality Products Online at: sales@GlobalTestSupply.com
www.GlobalTestSupply.com
RFC1000-IP69K
Compliance Information
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
To satisfy FCC RF Exposure requirements for mobile and base station transmission devices,
a separation distance of 20 cm or more should be maintained between the antenna of this
device and persons during operation. To ensure compliance, operation at closer than this
distance is not recommended. The antenna(s) used for this transmitter must not be co-located
or operating in conjunction with any other antenna or transmitter.
This device complies with Industry Canada license-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this device may not cause interference, and (2)
this device must accept any interference, including interference that may cause undesired
operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils
radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: (1)
l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout
brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le
fonctionnement.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna
of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada.
To reduce potential radio interference to other users, the antenna type and its gain should
be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that
necessary for successful communication.
Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut
fonctionner avec une antenne d’un type et d’un gain maximal (ou inférieur) approuvé
pour l’émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage
radioélectrique à l’intention des autres utilisateurs, il faut choisir le type d’antenne et son gain
de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l’intensité
nécessaire à l’établissement d’une communication satisfaisante.
Countries approved for use, purchase and distribution:
USA, Canada, Chile, Columbia, Ecuador, Honduras, India, Malaysia, Mexico, Peru, Singapore,
South Africa, Thailand, Venezuela, Vietnam
9
Find Quality Products Online at: sales@GlobalTestSupply.com
www.GlobalTestSupply.com
Product User Guide
General Specifications
Interface Type USB (to PC), Wireless (to Data Logger)
RFC1000-IP69K: -20 °C to +85 °C (-4 °F to +185 °F), 0 %RH to 100 %RH
Operating Environment
LED Indicators
Enclosure Materials
Transmission Distance
to Data Logger
Transmission Distance
to RFC1000-IP69K
Compatible Data Loggers RFOT, Therm•A•lert and RF2000A Series
Maximum number of
connected data loggers
Frequency 2.405 GHz - 2.475 GHz
Ingress Protection IP69K
Dimensions
Weight 14.1 oz (400 g)
Approvals
non-condensing
Power Supply: 0 °C to +40 °C (+32 °F to +104 °F), 20 %RH to 85 %RH
non-condensing
Power: Red
Data: Green
Body: Acetal Plastic
Cover: 300 Series Stainless Steel
Antenna Boot: Neoprene
Unobstructed line-of-sight (outdoors): 2,000 feet max
Typical urban environment (indoors): 500 feet max
Unobstructed line-of-sight (outdoors): 4,000 feet max
Typical urban environment (indoors): 1,000 feet max
64
Body: 3.4 in x 2.9 in x 1.3 in (86.36 mm x 73.66 mm x 33.02 mm)
Antenna: 7.5 in (190 mm)
FCC ID: OA3MRF24J40MC, IC#: 7693A-24J40MC,
ETSI 300 328 (EU R&TTE)
10
Find Quality Products Online at: sales@GlobalTestSupply.com
www.GlobalTestSupply.com
Loading...