MadgeTech PRTemp1000IS-5000-PSIA User manual

Red 485
Dark Blue Pantone 289
Light Blue 58% of Pantone 289

Red 485
Dark Blue Pantone 289
Light Blue 58% of Pantone 289

Description PRTemp1000IS

Temperature Sensor Internal semiconductor

Temperature Range -40 °C to +80 °C (-40 °F to +176 °F)

Temperature Resolution 0.1 °C (0.18 °F)

Calibrated Accuracy

Pressure Range

Pressure Resolution

Pressure Accuracy

Memory 16,383/channel

Reading Rate 1 reading every 2 seconds up to 1 reading every 12 hours

Units PSIA(G), inches, altitude, Torr, mmHg, Pascals

Required Interface Package IFC200

Baud Rate 2,400

Typical Battery Life 1 year

Operating Environment -40 °C to +80 °C (-40 °F to +176 °F), 0 %RH to 100 %RH

Material 303 stainless steel

Dimensions 6.4 in x 1.25 in dia. (163 mm x 32 mm dia.)

Weight 12 oz (340 g)

Approvals CE, IS Rated

+0.5 °C (+0.9 °F)

*See Table Below

Product User Guide

PRTemp1000IS

*PRTemp1000IS

Range (PSI)

Accuracy

Resolution (PSI)

0-30 0-100 0-300 0-500 0-1000 0-5000

2 % FSR, 0.25 % @ 25 °C typical

0.002 0.005 0.02 0.05 0.05 0.2

Battery Warning

WARNING: FIRE, EXPLOSION, AND SEVERE BURN HAZARD. DO NOT SHORT CIRCUIT, CHARGE,
FORCE OVER DISCHARGE, DISASSEMBLE, CRUSH, PENETRATE OR INCINERATE. BATTERY MAY
LEAK OR EXPLODE IF HEATED ABOVE 80 °C (176 °F).

DOC-1124035-00 REV 12 08.07.2017

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

PRTemp1000IS

Intrinsically Safe Pressure and Temperature Data Logger

PRTemp1000IS

Product User Guide

Product Notes

Getting Started

To access the COM Port for the interface cable, unscrew the key-ring end cap. Screw the
end cap back onto the data logger until the o-ring cannot be seen, before deploying the
data logger.

Intrinsic Safety Approval

The PRTemp1000IS has been certied by FM Approvals as Intrinsically Safe (IS) for use in
Class I, Division 1, groups A, B, C, D, and Non-incendive (NI) for use in Class I, Division 2,
groups A, B, C, D Hazardous (Classied) Locations. The rating listed in the Factory Mutual
approval guide is as follows: PRTemp1000IS. Pressure & Temperature Recorder. IS / I / 1 /
ABCD T4A Ta=80 °C; NI / I / 2 / ABCD / T4A Ta=80 °C
Special Condition of Use:

1. Use only with Tadiran Battery P/N TL-2150: These are the only safety ratings relevant
to the use of this product. Use of this product in hazardous environments not specically
covered by this rating, is prohibited, unless the user takes the appropriate steps to ensure
the safety of the product and assumes full responsibility for its safe use.

Pressure Sensor

To use the pressure sensor for gauge measurements, screw the ¼” male NPT tting into
the pipe to be measured with a 9/16” wrench. The NPT tting can be used for absolute
and submersible applications, but it is preferable to use the submersible tting.

O-Rings

O-ring maintenance is a key factor when properly caring for the PRTemp1000IS. The
o-rings ensure a tight seal and prevent liquid from entering the inside of the device.
Please refer to the application note “O-Rings 101: Protecting Your Data”, found on the
MadgeTech website, for information on how to prevent O-ring failure.

Installation Guide

Installing the Interface cable

- IFC200: Insert the device into a USB port. The drivers will install automatically.

Device Operation

Connecting and Starting the data logger

- Once the software is installed and running, plug the interface cable into the data logger.

- Connect the USB end of the interface cable into an open USB port on the computer.

- The device will appear in the Connected Devices list, highlight the desired data logger.

- For most applications, select “Custom Start” from the menu bar and choose the desired
start method, reading rate and other parameters appropriate for the data logging
application and click “Start”. ( “Quick Start” applies the most recent custom start options,
“Batch Start” is used for managing multiple loggers at once, “Real Time Start ” stores the
dataset as it records while connected to the logger.)

- The status of the device will change to “Running”, “ Waiting to Start” or “Waiting to Manual Start”,

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

depending upon your start method.

- Disconnect the data logger from the interface cable and place it in the environment to
measure.

Note: The device will stop recording data when the end of memory is reached or the device is stopped. At this
point the device cannot be restarted until it has been re-armed by the computer.

Downloading data from a data logger

- Highlight the data logger in the Connected Devices list. Click “Stop” on the menu bar.

- Once the data logger is stopped, with the logger highlighted, click “Download”. You will
be prompted to name your report.

- Downloading will ooad and save all the recorded data to the PC.

Device Maintenance

Battery Replacement

Materials:

- Remove the end cap of the data logger, the retaining clip using pliers and the white
Teon washer.

- VERY CAREFULLY use a 9/16” (15 mm) wrench to remove the NPT end of the data logger.

- Once the NPT end is completely unscrewed, gently slide the circuit board out of the
enclosure. Be careful not to break or sharply bend the cable between the level sensor and
the electronics.

- The battery is the purple cylinder on the circuit board, gently pull out the battery.

- Insert the new battery one lead at a time, pressing rmly with your index nger to make
sure the lead is secure in its terminal. Note: The battery should be at against the circuit board, and the

positive lead should be closest to the communications jack.

- Insert the electronics back into the tube. Make sure the cable is not twisted, sharply bent,
or kinked. From the connection to the circuit board, it should run up towards the battery,
then down the sensor.

- VERY CAREFULLY screw the NPT end cap back onto the tube, making sure the electronics
rotate with the end cap.

- Insert the Teon washer and retaining clip to secure the electronics and replace the end cap.

Recalibration

The PRTemp1000IS standard
temperature calibration is one
point at 25 °C. The pressure
calibration is dependant upon
the range.

Additional Services:
Custom calibration and verication point options available, please call for pricing.

Snap ring Pliers, 9/16” (15mm) wrench and a teplacement Battery (TL-2150)

Range (PSIA)

Range (PSIG)

Calibration

Point (PSIA)

0-30 0-100 0-300 0-500 0-1000 0-5000

0-30 0-100 0-300 0-500 - -

~14.7 and

~14.7 and

27-30

90-100

~14.7 and

270-300

~14.7 and

270-300

~14.7 and

450-500

~14.7 and

450-500