MadgeTech PHTemp101 Quick Start Guide

Red 485
Dark Blue Pantone 289
Light Blue 58% of Pantone 289

Red 485
Dark Blue Pantone 289
Light Blue 58% of Pantone 289

Product Quick Reference Card

Device Maintenance

Battery Replacement

Materials:

Small Phillips Head Screwdriver
Replacement Battery (U9VL-J)

- Puncture the center of the back label with the screw driver
and unscrew the enclosure.

- Remove the battery by pulling it out of the terminal snaps.

- Snap the new battery into the terminals and verify it is secure.

- Screw the enclosure back together securely.

Note: Be sure not to over tighten the screws or strip the threads.

Battery Warning

WARNING: FIRE, EXPLOSION, AND SEVERE BURN HAZARD. DO NOT
SHORT CIRCUIT, CHARGE, FORCE OVER DISCHARGE, DISASSEMBLE,
CRUSH, PENETRATE OR INCINERATE. BATTERY MAY LEAK OR
EXPLODE IF HEATED ABOVE 60°C (140°F).

Recalibration

The pHTemp101 standard calibration is performed at 50 Ohms
and 150 Ohms for the RTD channel and 0mV and 250mV for the
pH channel.

Note: MadgeTech does not offer calibration of pH inputs in
combination with a pH electrode or probe.

Pricing:

Recalibration traceable to NIST $90.00
Recalibration $70.00

Additional:

As Found Data $15.00 per parameter/channel
Verification Point $15.00 per point

To send the devices back, visit www.madgetech.com, select
Services then RMA Process.

Part Number pHTemp101

pH Input Connection Female BNC jack

pH Range 0 to 14pH (+1000mV )

pH Resolution 0.01pH

pH Accuracy +0.1pH

Temperature Sensor 2, 3 or 4 Wire 100W, platinum RTD

Probe Temperature Range -0 to +100°C

Temperature Resolution 0.01°C

Accuracy +0.1°C

Memory 13,107/channel

Sample Rate 2 seconds up to 12 hours

Required Interface Package IFC110 or IFC200

Baud Rate 2,400

Typical Battery Life 1 year

Operating Environment -5 to +50°C (0 to 95%RH non-condensing)

Materials ABS plastic

Dimensions 2.4” x 4.5” x 1.0” (61mm x 115mm x 26mm)

Approvals CE

Specifications subject to change.

See MadgeTech’s terms and conditions at www.madgetech.com

MadgeTech, Inc.

PO Box 50

Phone [phone]

www.madgetech.com

l

Warner, NH 03278

l

Fax [phone]

l

[e-mail]

Product Information Card

pHTemp101

pHTemp101

pH and Temperature Recorder

To view the full MadgeTech product line,

visit our website at www.madgetech.com.

REV D 2009.06.11

pHTemp101

3-Red

4-Red or Short to 3

1-Black or Short to 2

2-Black

Connector for 100
Ohm PtRTD

IFC101 connector

BNC connector for
pH electrode

Product Notes

Installation Guide

Product Quick Reference Card

Device Operation

LEDs

Once started, the LED will flash at the selected reading rate to
indicate that the device is running.

Using the pHTEMP101

1. The pH electrode should have a BNC output connection, or an
appropriate adapter. Select a probe with an output impedance
less than 300 megaohms at the desired temperature. The
OMEGA PHE-4200 Series of probes satisfy this condition
above 0 ºC (32 ºF), and have a BNC output connection.

2. The temperature probe must be a 100 ohm platinum RTD, in
the standard 2-,3- or 4-wire configuration. The pHTEMP101
is designed to achieve exceptional accuracy with the 4-wire
probe, but will still yield measurements better than required
for a pH-measurement with the 2- or 3-wire probes.

3. Insure that the probe you select can be connected to the
Phtemp101 RTD input by selecting a probe with lead wires,
or by attaching an adapter that will allow you to connect
wire leads to the probe. OMEGA’s PR-10 and PR-11 series
of probes have the proper leads for direct connection to the
Phtemp101.

4. Connect the probes to the data logger.

5. Refer to the description of your pH probe
for a calibration procedure.

KEY

4- Excitation Current Out (+)
3-Measurement (+) Input
2- Measurement(-) Input
1- Ground (-)

Installing the Interface cable

- IFC200, IFC202 or IFC300
Refer to the “Quick Start Guide” included in the package.

- IFC110, IFC102 or IFC103
Plug the serial cable into the port and verify it is secure.

- USB-1 or USB-101
Install the USB drivers from the CD provided in the kit, than

plug the USB cable into the computer and the serial cable into
the serial port.

Installing the software

Insert the Software CD in the CD-ROM Drive. If the autorun
does not appear, locate the drive on the computer and double
click on Autorun.exe. Follow the instructions provided in the
Wizard.

Connecting the data logger

- Once the software is installed and running, plug the interface
cable into the data logger.

- Click the Communication Menu, then Auto Configure Port.

- After a moment, a box similar to the following will appear;

Starting the data logger

- Click Device Menu then
Start Device.

- Choose the desired start
method.

- Choose the start parameters
by selecting a Reading Rate
suitable for your application.

- Enter in any other desired
parameters and click Start.

- A box will appear stating the
data logger has been started.
Click OK.

- Disconnect the data logger from the interface cable and
place it in the environment to measure.

Note: The device will stop recording data when the end of
memory is reached or the device is stopped. At this point the
device cannot be restarted until it has been re-armed by the
computer.

Downloading data from a data logger

- Connect the data logger to the interface cable.

- Click the Device Menu then Read Device Data. This will
offload all recorded data onto the PC.

Engineering Units

Engineering units are used to convert one measurement

reading to another. Please refer to the app note “Engineering
Units”, found on the MadgeTech website, for information on
how to manage Engineering Units.

- Click OK. The Device Status box will appear. Click OK.

- At this point, communications have been configured for your
logger. These settings can be found under the Communication
Menu.

Note: For additional installation instructions refer to your “Data
Logger & Software Operating Manual”.

Technical Support

Visit www.madgetech.com, or call [phone].
Technical support is also available by e-mailing
[e-mail]

Additional product information is available by e-mailing
[e-mail].