Page 1
Red 485
Dark Blue Pantone 289
Light Blue 58% of Pantone 289
Description HiTemp140-PT-1 HiTemp140-PT-5
Temperature Sensor 100 Ω Platinum RTD
Probe Measurement Range
Temperature Resolution 0.01 °C (0.02 °F)
Calibrated Accuracy
Memory 32,700 readings
Reading Rate 1 reading every second up to 1 reading every every 24 hours
Required Interface Package IFC400 or IFC406
Baud Rate 125,000 baud
Typical Battery Life 1 year typical (1 minute reading rate at 25 °C/77 °F)
Operating Environment
Material 316 Stainless Steel
Dimensions (Body) 1.9 in x 0.97 in dia. (48 mm x 24.6 mm dia.)
Weight 4.2 oz (120 g)
Submersible Yes (IP68)
Approvals CE
Model Number Dimensions (Probe)
HiTemp140-PT-1
HiTemp140-PT-5
-40 °C to +140 °C (-40 °F to +284 °F), 0 %RH to 100 %RH, 0.002 PSIA
Probe tip: 4.8 in x 0.125 in dia. with 1 in x 0.188 in dia. handle
-200 °C to +350 °C (-328 °F to +662 °F)
*BODY OF LOGGER CANNOT EXCEED 140 °C
±0.1 °C/±0.18 °F (20 °C to +140 °C/68 °F to +284 °F)
±0.3 °C/±0.54 °F (-20 °C to +19.99 °C/-4 °F to +67.98 °F)
±0.4 °C/±0.72 °F (-40 °C to –20.01 °C/-40 °F to -4.02 °F)
to 100 PSIA
Probe tip: 1.7 in x 0.125 in dia. (42 mm x 3.2 mm dia.)
(121 mm x 3.2 mm dia. with 25 mm x 4.8 mm dia. handle)
*BODY OF LOGGER CANNOT EXCEED 140 °C
Bendable portion: 22 in x 0.062 in dia.
(559 mm x 1.6 mm dia.)
Bendable portion: 22 in x 0.062 in dia.
(559 mm x 1.6 mm dia.)
Product User Guide
HiTemp140-PT Series
IFC400 (Sold Separately)IFC406 (Sold Separately)
Battery Warning
W
ARNING: FIRE, EXPLOSION, AND SEVERE BURN HAZARD. DO NOT SHORT CIRCUIT, CHARGE,
FORCE OVER DISCHARGE, CRUSH, PENETRATE OR INCINERATE. BATTERY MAY LEAK OR EXPLODE
IF HEATED ABOVE 150 °C (302 °F).
Specifications subject to change.
Find Quality Products Online at: sales@GlobalTestSupply.com
DOC-1236035-00 REV 3 02.21.2017
www.GlobalTestSupply.com
HiTemp140-PT Series
High Temperature Data Loggers with 24” Bendable Stainless Steel Probes
1 inch and 5 inch probes available
Page 2
HiTemp140-PT
Product User Guide
Product Notes
The HiTemp140-PT is a submersible, temperature data logger that can operate from 20 °C
up to 140 °C (284 °F) and has an accuracy of +/-0.1 °C (0.18 °F). The device features a 24
inch bendable stainless steel probe for measuring extended temperatures up to 350 °C (662
°F). The probe is durable and can be spiraled, bent or angled in any direction, making it easy
to log temperatures within bottles, vials or other hard to reach places.
Submergibility
The HiTemp140-PT is fully submersible and is rated IP68. It can be placed in environments
with up to 230 feet (70 m) of water.
Bend Radius
The exible probe on the HiTemp140-PT can be bent to a 1/4 inch bend radius. The probe
should not be bent within 1 inch of either weld joint.
O-Rings
O-ring maintenance is a key factor when properly caring for the HiTemp140-PT. The O-rings
ensure a tight seal and prevent liquid from entering the inside of the device. Please refer to
the application note “O-Rings 101: Protecting Your Data”,
for information on how to prevent O-ring failure.
Note: This product is rated for use up to 140 °C. Please heed the battery warning. The product will explode if exposed to
temperatures above 140 °C.
Installation Guide
Installing the Interface cable
- IFC400 or IFC406
Refer to the “Quick Start Guide” included in the package.
- The status of the device will change to Running, Waiting to Start or Waiting to Manual
Start, depending upon your start method.
- Disconnect the data logger from the docking station and place it in the environment to
measure.
Note: The device will stop recording data when the end of memory is reached or the device is stopped, unless user selectable
memory wrap is enabled. At this point the device cannot be restarted until it has been re-armed by the computer.
Downloading data from a data logger
- Place the logger into the docking station.
- Highlight the data logger in the Connected Devices list. Click Stop on the menu bar.
- Once the data logger is stopped, with the logger highlighted, click Download. You will
be prompted to name your report.
- Downloading will ooad and save all the recorded data to the PC.
Device Maintenance
Battery Replacement
Materials:
ER1425S-HT Battery
- Unscrew the bottom of the logger and remove the battery.
- Place the new battery into the logger. Note the polarity of the battery.
- Screw the cover back onto the logger.
Recalibration
The HiTemp140-PT standard calibration points are +20 °C and +140 °C.
Prices and specifications subject to change.
Installing the software
Follow the
instructions provided in the Installation Wizard to install the MadgeTech Software.
Device Operation
Connecting and Starting the data logger
- Once the software is installed and running, plug the interface cable into the docking station.
- Connect the USB end of the interface cable into an open USB port on the computer.
- Place the data logger into the docking station.
- The data logger will automatically appear under Connected Devices within the software.
- For most applications, select Custom Start from the menu bar and choose the desired start
method, reading rate and other parameters appropriate for the data logging application
and click Start. (Quick Start applies the most recent custom start options, Batch Start is used
for managing multiple loggers at once, Real Time Start stores the dataset as it records while
connected to the logger.)
Find Quality Products Online at: sales@GlobalTestSupply.com
www.GlobalTestSupply.com
Loading...