6-CHANNEL
WIRELESS INTERCOM
MODEL:HY-806
Hosmart was founded in 2012 by a former group of Motorola
engineers and designers. Now fast forward a few years and
we are now the industries leader in home intercom and
security products.
Our vision is to become the world leader in home intercom
products and soluons. We design as well as engineer
intelligent home intercom systems. We want to be your
homes soluon. Our company philosophy is to focus our
efforts and energy based on our client's wishes.
We are confident that you will enjoy and be sasfied with
our products. Any damage or malfuncon of Hosmart
product is 100% guaranteed to be replaced.
BATTERY
The intercom can also run on an 18650 baery as backup, for
up to one week, depending on use. The 18650 baery is not
included in the package. We recommend installing a
3.7V/2800mAh for beer baery life.
The red light will illuminate while charging, The red light will
turn off once the baery is fully charged.
Recommended Oponal
+ -
DC 5V
OVERVIEW
The intercom has a range of 1/2 mile and can simultaneously
handle mulple conversaons using a 462Mhz secure digital
radio link. The intercom is a half-duplex TDD FM transceiver
that alternates between a transming or receiving state.
Speaker
Channel
select buon
Volume
Control
Antenna
正面
MONITOR
ON/OFF
TALK
FEATURES
ANT(antenna)
Sends and received FM wireless signal.
MIC
Speak towards MIC (30-40 cm away) with normal volume.
CALL
To make a call, select the channel you want to communicate
with and press “CALL”.
TALK (+ Low Baery Indicator)
The red LED indicator will keep flash on Talk buon if the
baery is low.
Press and hold "TALK" when speaking. Release "TALK"
to listen for a response. The indicator turns off when
transmission is complete.
The TALK buon red LED indicator will flash when
the baery is low.
ON/OFF (+ Monitor Mode)
ON / OFF: Plug the intercom into an outlet with the AC
adapter. The unit will turn on automacally. Aer installing
the baery, press ON/OFF to turn on the intercom, press
and hold “ON/OFF” for 3 seconds to turn OFF.
Monitor Mode: Press “Monitor” to put the intercom in
monitor mode. The unit will be monitored for 24 hours
by other units that have been set to the same channel.
If you have any questions with the unit, please contact us by
navigating to www.myhosmart.com, then click Warranty, and fill
out the form, we will assist you as quickly as possible.
E-mail: service@hosmartmall.com
Phone: (502)-341-7705
Note: Your call is very important to us, if we can not answer your call
on time ,we will reply your call in 24 hours.
Press any funcon buon to exit Monitor mode.
GROUP (Group-Call Funcon)
Press and hold “GROUP” to talk to all intercoms simultaneously,
even the device in different channel.
0-5 channel number
Set the channel for each intercom. The default channel is #1.
Volume Adjustment (VOL+/VOL-)
Press "VOL -" or "VOL +" to decrease or increase the volume
level. A tone will sound when you have reached the maximum
or minimum limit.
N
ote: To choose different ring tones:
Step1. Press and hold the "VOL-" to enter the chimes select
mode.
Step2. Press "CALL" to choose the ring tone you like.
Step3. There are 4 different chimes you may choose.
Exit this mode by Pressing any funcon buon.
SETTING CHANNEL
Please set different channel for different devices by
following steps :
1). Use the AC adapter to plug the intercom into a power outlet.
2). Set the channel for each intercom. The default channel
is #1. Set the channel by pressing and holding one of the
channel buons(1 thru 5 or 0) for 3 seconds, unl you
AC adapter
hear the Beep
and the channel buon lights. Set channels
Install 18650 baery (not provided).
on addional intercoms using the same steps. Intercoms
may be set to the same or different channel numbers
depending on intended use.
3). Make a note of all units that share the same channel
number to enable rapid and accurate communicaon.
For example:
Channel
Device
Locaon
2
General
Manager Room
3
Conference
Room
4
Finance
5
HR
USING ADDITIONAL STATIONS
You may add addional staons to the system as long as
they transmit on the same frequency.
OPERATION
Receive a Call
A device will emit a series of rings when receiving a call
from another device. Press and hold the TALK buon to
answer the call, and speak 30-40 cm toward the MIC in a
normal voice. The blue LED indicates that Talk mode is
acve. Release the TALK buon to listen for a reply. All
devices set to the same channel will receive the
transmission.
ON/OFF
TALK
MIC
Funcon
buon
Make a Call
Select the desired channel by pressing and releasing a
channel buon, then press CALL. This will ring all devices
set to that channel. Connue the conversaon as described
in “Receive a call”.
Notes:
• You will not be able to hear a transmission from another
device while you are pressing the TALK buon.
• When talk ends, the channel of calling unit automacally
change to the originally set channel aer 1 minute.
CAUTIONS
The following will help you maintain your wireless intercom
for years to come.
* Keep staons from geng wet, as they are not waterproof.
* Keep staons in a control environment. Avoid extreme
temperatures.
* Handle the staons with care. Do not drop, throw, or
mishandle the staons.
* Keep staons clean from dust and dirt as this can damage
the sensive electronics.
* Do not use chemicals or cleaning solvent. Use a damp
cloth to clean the staon.
* Modifying or tampering with the staons internal
components can cause it to malfuncon, and will also
void your warranty.
* If your product is not working as adversed then return
it to local retailer for assistance or contact us at our
e-mail.
If you have any questions with the unit, please contact us by
navigating to www.myhosmart.com, then click Warranty, and fill
out the form, we will assist you as quickly as possible.
E-mail: service@hosmartmall.com
Phone: (502)-341-7705
Note: Your call is very important to us, if we can not answer your call
on time ,we will reply your call in 24 hours.
THE FCC WANTS YOU TO KNOW
Your intercom may cause TV or radio interference. To be certain
turn off your intercom and check your TV or radio on
its performance. If sll receiving interference, rest a
sure it is not your intercom. You may try to eliminate
interference by:
* Moving your staons further away from the receiver.
* Moving your staons further away from your TV or radio.
If these opons do not solve your problem the FCC requires
you to stop using your intercom. Change or modificaons
not approved by the party responsible for compliance
coud void the user authority to operate the equipment.
Troubleshoong
Can not talk to other
intercom
Intercom is not geng expected
transmission range
Stac and feedback is heard
in intercom
-Please check if the baery is fully charged.
-If the intercom is set in Monitor Mode.
-You will not be able to hear a transmission from
another device while you are pressing the TALK
buon.
-Press and hold down TALK to communicate
aer other unit finished talk.
- Are the intercoms too close causing Audio
feedback?
If the walls are too thick or if the building
is mental causing no signal to pass through?
-Change locaon by using Power Bank, moving
to other locaons for beer recepon and
transmission.
-Keep intercom away from metal objects and
electrical wiring.
-The intercoms are too close to each other.A
cordless phone,cell phone or other radio devices
can also cause stac.
Note:
Monitor Fucon- For connuous talk or room monitoring
which can last up to 24 hours.
FRS Frequencies
Limited 12 months Warranty
EXCEPT AS PROVIDED HEREIN, SELLER MAKES NO EXPRESS
WARRANTIES AND ANY IMPLIED WARRANTIES, INCLUDING
THOSE OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO
THE DURATION OF THE WRITTEN LIMITED WARRANTIES
CONTAINED HEREIN, EXCEPT AS PROVIDED HEREIN, SELLER
SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO CUSTOMER
OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY
LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY
BY USE OR PERFORMANCE OF THE PRODUCT OR ARISING
OUT OF ANY BREACH OF THIS WARRANTY, INCLUDING,
BUT NOT LIMITED TO ANY DAMAGES RESULTING FROM
INCONVENIENCE, LOSS OF TIME, DATA, PROPERTY, REVENUE,
OR PROFIT OR ANY INDIRECT, SPECIAL, INCIDENTAL,OR
CONSEQUENTIAL DAMAGES,EVEN IF SELLER HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
In the event of a product defect during the warranty period,
contact the Seller to obtain an RBM#, and then return the
product, along with the sales receipt as proof of purchase
date, to Seller. The Seller will, at its opon either correct
the defect by product repair without charge for parts and
labor; replace the product with one of the same or similar
design or refund the purchase price.
All replaced parts and products and refunded products
become the property of the Seller. New or recondioned
背面
parts and products may be used in the performance of
warranty service. Repaired or replaced parts and products
are warranted for the remainder of the original warranty
period. You will be charged for repairs on products no
longer covered by warranty.
For all returns, please write down the RBM# and return
date on the outside of the package. This will speed up
the process of handling your return and issuing a refund
or providing you with a replacement. Refunds are not
issued for products no longer covered by warranty. The
warranty will not cover replacements in cases where
damage or failure is caused by, or aributable to:
(a) acts of God, abuse, accident, misuse, improper abnormal
usage, failure to follow instrucons, improper installaon
or maintenance, alteraon, lightning or other instance of
excess voltage or current,
(b) any repairs other than those provided by the Seller,
(c) consumables such as fuses or baeries,
(d) cosmec damage,
(e) transportaon, shipping or insurance costs,
(f) or costs of product removal, installaon, set-up, service
adjustment or reinstallaon.
Our goal is for you to have the best possible experience
with Hosmart. We appreciate receiving comments on any
aspect of your experience with Hosmart or our products.
Please contact us with any problems, prior to leaving any
online feedback, so that we may address your concern.
We guarantee your complete sasfacon for this transacon.
Please note that our office hours are 9:00 am to 5:00 pm
(GMT+8) Monday through Friday. Offices are closed
Saturday, Sunday and public holidays. We apologize for any
late replies during holidays.
If you have any questions with the unit, please contact us by
navigating to www.myhosmart.com, then click Warranty, and fill
out the form, we will assist you as quickly as possible.
E-mail: service@hosmartmall.com
Phone: (502)-341-7705
Note: Your call is very important to us, if we can not answer your call
on time ,we will reply your call in 24 hours.
FCC SATEMENT
FCC ID: FCC ID: 2AJEM-HY806
Power: DC 5V/1A , AC Adapter Voltage range: 100V-240V
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protecon against harmful interference in a
residenal installaon. This equipment generates uses and
can radiate radio frequency energy and, if not installed
and used in accordance with the instrucons, may cause
harmful interference to radio communicaons. However,
there is no guarantee that interference will not occur in
a parcular installaon. If this equipment does cause
harmful interference to radio or television recepon, which
can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference
by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separaon between the equipment and
receiver.
-- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician
for help.
This device complies with part 15 of the FCC Rules.
Operaon is subject to the following two condions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operaon.
Changes or modificaons not expressly approved by the
party responsible for compliance could void the user's
authority to operate the equipment.
– This radio is designed for and classified as “General population/uncontrolled Use”
– DO NOT operate the radio without a proper antenna attached, as this may damage the radio
and may also cause you to exceed RF exposure limits. A proper antenna is the antenna
supplied with this radio by the manufacturer or an antenna specifically authorized by the
manufacturer for use with this radio, and the antenna gain shall not exceed 2dBi by the
manufacturer declared.
– DO NOT transmit for more than 50% of total radio use time, more than 50% of the time can
cause RF exposure compliance requirements to be exceeded.
– During operation, the separation distance between user and the antenna shall be at least
20cm, this separation distance will ensure that there is sufficient distance from a properly
installed externally-mounted antenna to satisfy the RF exposure requirements
– During transmissions, your radio generates RF energy that can possibly cause interference
with other devices or systems. To avoid such interference, turn off the radio in areas where
signs are posted to do so. DO NOT operate the transmitter in areas that are sensitive to
electromagnetic radiation such as hospitals, aircraft, and blasting sites.
This product produced by:
Macross Microelectronics (HK) LIMIT
展开尺寸:420*296mm