M A COM SW90-0004TR, SW90-0004-TB, SW90-0004 Datasheet

GaAs SP6T Switch, Absorptive,
Single Supply, DC - 4 GHz

V 5.00

SW90-0004

Features

n Operates DC - 4 GHz on Single Supply
n ASIC TTL / CMOS Driver
n Leadless 4 x 7 mm Chip Scale Plastic Package
n Low DC Power Consumption
n 50 Ohm Nominal Impedance
n Test Boards are Available
n Tape and Reel are Available

Description

M/A-COM's SW90-0004 is a SP6T absorptive pHEMT
switch with integral TTL driver. This device is in an MLP
plastic surface mount package. This switch offers excellent
broadband performance and repeatability from DC to 4
GHz, while maintaining low DC power dissipation. The
SW90-0004 is ideally suited for wireless infrastructure
applications.

CSP-2

Electrical Specifications: TA = 25°C

Parameter Test Conditions Frequency Units Min. Typ. Max.

Insertion Loss RFC-RF1, 2, 3, 4, 5, 6 DC - 4.0 GHz dB — — 2.1

Isolation — DC - 4.0 GHz dB 25 — —

VSWR On (RFC, RF1-RF6)

1 dB Compression —

Input IP

3

Switching Speed Ton (50% Control to 10% RF) nS — 20 —

Vcc — — V 4.5 5.0 5.5
Logic “0” Sink Current is 20 µA max. — V 0.0 — 0.8
Logic “1” Source Current is 20 µA max. — V 2.0 — 5.0

Icc Vcc min to max, Logic “0” or “1” — mA — 5 8

Logic per Truth Table

Off (RF1-RF6)

Logic per Truth Table

—

Two-tone inputs up to +5 dBm 50 MHz

Toff (50% Control to 90% RF) nS — 15 —

Trise (10% to 90% RF) nS — 5 —

Tfall (90% to 10% RF) nS — 2 —

DC - 4.0 GHz
DC - 4.0 GHz

50 MHz

0.5 - 4.0 GHz

0.5-4.0 GHz

Ratio
Ratio

dBm
dBm

dBm
dBm

—
—

—
—

—
—

—
—

15
27

30
40

2.0:1

2.0:1

—
—

—
—

GaAs SP6T Switch, Absorptive, Single Supply, DC - 4 GHz

Pin Configuration

1,2,3

Absolute Maximum Ratings

SW90-0004

V 5.00

4,5

Pin No. Function Pin No. Function

1 CP2 19 GND
2 VEE 20 NC
3 NC 21 GND
4 C6 22 RFC
5 C5 23 GND
6 C4 24 GND
7 C3 25 RF4
8 C2 26 GND

9 C1 27 RF5
10 NC 28 GND
11 GND 29 RF6
12 NC 30 GND
13 GND 31 NC
14 RF1 32 VEE
15 GND 33 Vcc
16 RF2 34 NC
17 GND 35 NC
18 RF3 36 CP1

Parameter Absolute Maximum

Max. Input Power

0.05 GHz

0.5 - 4.0 GHz
Bias Voltages

VCC
Control Voltage 6

Operating Temperature -40°C to +85°C

Storage Temperature -65°C to +125°C

4. Operation of this device above any one of these
parameters may cause permanent damage.

5. When the RF input is applied to the terminated port, the
absolute maximum power is +30 dBm.

6. Standard CMOS TTL interface, latch-up will occur if logic
signal is applied prior to power supply.

-0.5V to VCC +0.5V

+27 dBm
+34 dBm

+5.5V

Functional Schematic

1. NC = No Connection

2. VEE is internally generated and must remain isolated from
external power supplies.

3. Connections and external components shown in functional
schematic are required. 0.1µF Capacitors need to be lo­cated near pins 32 & 33.

Recommended PCB Layout 7

7. Application Note C2083 is available on line at
www.macom.com

Specifications subject to change without notice.

n North America: Tel. [phone]
n Asia/Pacific: Tel.[phone], Fax [phone]
n Europe: Tel. [phone], Fax[phone]

Visit www.macom.com for additional data sheets and product information.

2