M A COM SW90-0001TR, SW90-0001-TB, SW90-0001 Datasheet

GaAs SPST Switch, Absorptive,
Single Supply, DC - 4 GHz

V 3.00

SW90-0001

Features

n Operates DC - 4 GHz on Single Supply
n ASIC TTL / CMOS Driver
n Leadless 4 x 6 mm Chip Scale Plastic Package
n Low DC Power Consumption
n 50 Ohm Nominal Impedance
n Test Boards are Available
n Tape and Reel are Available

Description

M/A-COM's SW90-0001 is a SPST absorptive pHEMT
switch with integral TTL driver. This device is in an MLP
plastic surface mount package. This switch offers excellent
broadband performance and repeatability from DC to 4
GHz, while maintaining low DC power dissipation. The
SW90-0001 is ideally suited for wireless infrastructure
applications.

CSP-1

Electrical Specifications: TA = 25°C

Parameter Test Conditions Frequency Units Min. Typ. Max.

Insertion Loss RF1—RF2 (All Logic “1”) DC - 4.0 GHz dB — — 0.85

Isolation RF1—RF2 (All Logic “0”) DC - 4.0 GHz dB 25 — —

VSWR On (RF1, RF2) (All Logic “1”) DC - 4.0 GHz Ratio — — 1.5:1
VSWR Off (RF1, RF2) (All Logic “0”) DC - 4.0 GHz Ratio — — 1.5:1

1 dB Compression —

Input IP3 Two-tone inputs up to +5 dBm 50 MHz

Switching Speed Ton (50% Control to 10% RF) nS — 32 —

Vcc — — V 4.5 5.0 5.5
Logic “0” Sink Current is 20 µA max. — V 0.0 — 0.8
Logic “1” Source Current is 20 µA max. — V 2.0 — 5.0

Icc Vcc min to max, Logic “0” or “1” — mA — 5 8

Toff (50% Control to 90% RF) nS — 20 —

Trise (10% to 90% RF) nS — 7 —

Tfall (90% to 10% RF) nS — 2 —

—

50 MHz

0.5 - 4.0 GHz

0.5-4.0 GHz

dBm
dBm

dBm
dBm

—
—

—
—

24
30

40
48

—
—

—
—

GaAs SPST Switch, Absorptive, Single Supply, DC - 4 GHz

SW90-0001

V 3.00

Pin Configuration

Pin No. Function Pin No. Function

1 NC 17 NC
2 NC 18 NC
3 C1 19 VCC
4 NC 20 NC
5 NC 21 CP2

6 NC 22 NC
7 NC 23 CP1
8 NC 24 NC

9 NC 25 VEE
10 NC 26 GND
11 GND 27 RF1
12 RF2 28 GND
13 GND 29 NC
14 NC 30 VEE
15 NC 31 NC
16 NC 32 VCC

1. NC = No Connection

2. VEE is internally generated and must remain isolated from
external power supplies.

3. Connections and external components shown in func­tional schematic are required. 0.1 µF Capacitors need to
be located near pins 30 & 32.

1,2,3

Absolute Maximum Ratings

Parameter Absolute Maximum

Max. Input Power

0.05 GHz

0.5 - 4.0 GHz
Bias Voltages

VCC
Control Voltage 6

Operating Temperature -40°C to +85°C

Storage Temperature -65°C to +125°C

4. Operation of this device above any one of these
parameters may cause permanent damage.

5. When the RF input is applied to the terminated port, the
absolute maximum power is +30 dBm.

6. Standard CMOS TTL interface, latch-up will occur if logic
signal is applied prior to power supply.

-0.5V to VCC +0.5V

4,5

+27 dBm
+34 dBm

+5.5V

Truth Table

Control Input Condition of the Switch

C1 RF1 to RF2

0 Off
1 On

Recommended PCB Layout 7

Functional Schematic

Specifications subject to change without notice.

n North America: Tel. [phone]
n Asia/Pacific: Tel.[phone], Fax [phone]
n Europe: Tel. [phone], Fax[phone]

Visit www.macom.com for additional data sheets and product information.

7. Application Note C2083 is available on line at
www.macom.com

2