M A COM SW-395, SW-395TR Datasheet

3 Volt GaAs SPDT Switch, DC - 2.0 GHz SW-395
SW-395
3 Volt GaAs SPDT Switch DC - 2.0 GHz
Features
Low Insertion Loss: <0.7 dB @ 900 MHz
Low Power Consumption: <10µA @ =3 VDC
Very High Intercept Point: 52 dBm IP
Both Positive and Negative 3 to 8 V Control
Low Cost SOT-26 Package
3
Description
M/A-COM’s SW-395 is a GaAs monolithic switch in a low cost SOT-26 surface mount plastic package. The SW-395 is ideally suited for applications where very low power consumption, low intermodulation products, very small size and low cost are required. Typical application is an internal/external antenna select switch for portable telephones and data radios. In addi­tion, because of its low loss, good isolation and inherent speed, the SW-395 can be used as a conventional T/R swi tch or as an antenna diversity switch. The SW-395 can be used in power applications up to 0.5 Watts in sys tems such as cellular, PCN, GSM an other analog/digital wireless communications systems.
The SW-395 is fabricated using a mature 1-micron gate length GaAs MESFET process. The process feat ur es full chip passiva­tion for increased performance and reliability.
SOT-26
1
XX#Y
PIN 1
1. Dimensions are in: inches/mm
Ordering Information
Part Number Package
SW-395 PIN SOT-26 Plastic Package SW-395TR Forward Tape and Reel
1. Refer to Application Note M513 for reel size information.
1
Electrical Specifications: TA = +25°C
1
Parameter Test Conditions Units Min. Typ. Max.
Insertion Loss DC - 1.0 GHz dB 0.7 0.9
1.0 - 2.0 GHz dB 0.8 1.0
Isolation DC - 1.0 GHz dB 23 25
1.0 - 2.0 GHz dB 17 19 VSWR DC - 2.0 GHz 1.3:1 1 dB Compression Input Power (3V Control) 0.5 GHz dBm 27
Input Power (5V Control) 0.5 GHz dBm 28 Input Power (3V Control) 0.05 GHz dBm 16 Input Power (5V Control) 0.05 GHz dBm 18
,
T
T
rise
,
T
T
on
off
ransients
T
Input IP
fall
10% to 90% RF, 90% to 10% RF 50% Control to 90% RF, Control to 10% RF In-band
2
2-Tone, 5 MHz spacing, 3 V Control 0.05 GHz dBm 61
S
µ
S
µ
mV 38
7 8
+10 dBm each 0.5 GHz dBm 71
Input IP
3
2-Tone, 5 MHz spacing, 3 V Control 0.05 GHz dBm 48 +10 dBm each 0.5 GHz dBm 52
1. All measurements at 1 GHz in a 50Ω system with a 3V control unless otherwise specified. Loss varies at 0.003 dB/°C.
M/A-COM Division of AMP Incorporated Q North America: Tel. (800) 366-2266, Fax (800) 618-8883 Q Asia/Pacific: Tel.+85 2 2111 8088, Fax +85 2 2111 8087
Q
Europe: Tel. +44 (1344) 869 595, Fax+44 (1344) 300 020
www.macom.com
AMP and Connecting at a Higher Level are trademarks.
V2.00
3 Volt GaAs SPDT Switch, DC - 2.0 GHz SW-395
ISOLATION vs FREQUENCY
VSWR vs FREQUENCY
INSERTION LOSS vs FREQUENCY
Absolute Maximum Ratings
1
Parameter Absolute Maximum
Input Power +33 dBm Operating Voltage +8.5 Volts Operating Temperature -40°C to +85°C
Storage Temperature -65°C to +150°C
1. Exceeding any one or a combination of these limits may cause permanent damage.
Truth Table
Mode
(Control)
1
Positive
Positive/ Negative
Negative
1,2
3
1. External DC blocking capacitors are required on all RF ports.
2. |-Vc|<
8 V.
3. If negative control is used, DC blocking capacitors are not re­quired on RF ports.
Control
A
0±0.2V
+3V to +8V
-Vc±0.2V +Vc
0±0.2V
-3V to -8V
ControlBRFC - RF1 RFC - RF2
+3V to +8V
0±0.2V
+Vc
-Vc±0.2V
-3V to -8V 0±0.2V
Off On
On Off
On Off
On Off
Off On
Off On
Functional Schematic
VA RFC VB
PIN 1
RF 1 G ND RF 2
1
1. DC blocking capacitors not required if negative control voltage is used.
Typical Performance Curves
Insertion Loss vs. Frequency VSWR vs. Frequency
1
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
INSERTION LOSS (dB)
0
00.511.522.533.5
Isolation vs Frequency
50 45 40 35 30 25 20 15
ISOLATION (dB)
10
5 0
00.511.522.533.5
FREQUENCY (GHz)
FREQUENCY (GHz)
1.5
1.4
1.3
1.2
VSWR (dB)
1.1
1
0 0.5 1 1.5 2 2.5 3 3.5
FREQUENCY (GHz)
M/A-COM Division of AMP Incorporated Q North America: Tel. (800) 366-2266, Fax (800) 618-8883 Q Asia/Pacific: Tel.+85 2 2111 8088, Fax +85 2 2111 8087
Q
Europe: Tel. +44 (1344) 869 595, Fax+44 (1344) 300 020
www.macom.com
AMP and Connecting at a Higher Level are trademarks.
V2.00
Loading...