MACOM DS56-0001-TR, DS56-0001-RTR, DS56-0001 Datasheet

Six-Way SMT Power Divider DS56-0001

g

DS56-0001

Low Cost Six-Way SMT Power Divider
824 - 960 MHz

Features

• Small Size, Low Profile

• Superior Repeatability (Lot-to-lot Variation)

• Industry Standard SOW-16 SMT Plastic Package

• Typical Isolation: 25 dB

• Typical Insertion Loss: 0.3 dB

• Low Cost

• 1 Watt Power Handling

Description

M/A-COM’s DS56-0001 is an IC-based monolithic power divider
in a low cost SOW-16 plastic package. This 6-way power divider
is ideally suited for applications where PCB real estate is at a
premium and part count reduction and cost are critical. Typical
applications include base station switching networks and other
cellular equipment, including subscriber units. Available in tape
and reel.

The DS56-0001 is fabricated using a passive-integrated circuit
process. The process features full-chip passivation for increased
performance and reliability.

SOW-16

Pin 16

Orientation

Mark

Pin 1

.3977-.4133

(10.10-10.50)

-A-

.004 (0.10)

0.050(1.27) BSC.

.010(0.25) M C A M B S

(All dimensions per JEDEC No. MS-013-AA, Issue C)

Unless Otherwise Noted: .xxx = 0.010 (.xx = 0.25)

.013-.020 TYP

(0.33-0.51)

16-Lead SOP outline dimensions

Wide body (.300)

Dimensions in ( ) are in mm.

Ordering Information

-B-

.0926-.1043

(7.40-7.60)

0-8

-C-

.0040-.0118

(0.10-0.30)

.xx = 0.02 (.x = 0.5)

.394-.419

(10.00-10.65)

.010(0.25) M B M

.010-.029 x
45 Chamfer
(0.25-0.75)

.016-.050

(0.40-1.27)

.0091-.0125

(0.23-0.32)

Part Number Package

DS56-0001
DS56-0001-TR
DS56-0001-RTR

1. If specific reel size is required, consult factory for part number
assignment.

SOW 16-Lead Plastic Packa
Forward Tape and Reel
Reverse Tape and Reel

1
1

Typical Electrical Specifications1, TA= +25ºC

Parameters Units Min. Typ. Max.

Insertion Loss Above 7.0 dB dB — 1.3 1.5
Isolation dB 20 25 —
VSWR — — 1.4:1 1.6:1
Amplitude Balance dB — 0.2 0.5
Phase Balance ° — 6 8

1. All specifications apply with a 50-ohm source and load impedance.

M/A-COM Division of AMP Incorporated ■ North America: Tel. [phone], Fax [phone] ■ Asia/Pacific: Tel.[phone], Fax [phone]
Europe: Tel. [phone], Fax+ 44 (1344) 300 020

■

e

V4.00

www.macom.com

AMP and Connecting at a Higher Level are trademark s.

Specifications subject to change without notice.

Six-Way SMT Power Divider DS56-0001

Absolute Maximum Ratings

1

Parameter Absolute Maximum

Input Power

2

Operating Temperature
Storage Temperature

1W CW

-40°C to +85°C

-65°C to 150°C

1. Exceeding these limits may cause permanent damage.

2. With internal load dissipati on of 0.125 W maximum.

Recommended PCB Configuration

(Dimensions in Inches)

.335

.093

TYP.

.041

TYP.

RF 4RF 3

.067

TYP.

RF 2

RF 1

RF 5

RF 6

.030

TYP.

.016 DIA.
PLATED

THRU (2 1X)

Functional Diagram

RF 3 (OUT)

1

GND

2

RF 2 (OUT)

3

GND

4

RF 1 (OUT)

5

GND

6

RF IN

7

GND

3

RF 4 (OUT)

16

GND

15

RF 5 (OUT)

14

GND

13

RF 6 (OUT)

12

GND

11

GND
10

GND

98

3. Pins 2, 4, 6, 8, 9, 10, 11, 13, and 15 must be DC and RF grounded.

RF IN

.428

Typical Performance @ +25°C

0

-0.5

-1.0

-1.5

INSERTION LOSS (dB)

-2.0
824 858 892 926 960

Isolation vs. Frequency

0

-10

-20

Frequency (MHz)

.050 DIA.
PLATED

THRU (3X)

VSWR vs. FrequencyInsertion Loss vs. Frequency

2.0

1.8

1.6

VSWR

1.4

1.2

1.0
824 858 892 926 960

Frequency (MHz)

Input

Output

-30

IS O L ATION (dB)

-40
824 858 892 926 960

Frequency (MHz)

M/A-COM Division of AMP Incorporated ■ North America: Tel. [phone], Fax [phone] ■ Asia/Pacific: Tel.[phone], Fax [phone]
Europe: Tel. [phone], Fax+ 44 (1344) 300 020

www.macom.com

AMP and Connecting at a Higher Level are trademark s.

Specifications subject to change without notice.

V4.00

■