MACOM DR65-0002TR, DR65-0002 Datasheet

Linear Driver for PIN Diode Attenuators
V 4.00
DR65-0002
Features
n Linearizes PIN Diode Attenuators Over a Wide
Attenuation Range
Description
M/A-COM's DR65-0002 is a break point free driver that produces a logarithmic output current suitable for linearizing PIN diode based shunt attenuators. This driver, in conjunction with customer defined external components, produces a linear transfer function (dB/V) between the input control voltage of the driver and the attenuation output of the PIN attenuator. The DR65-0002 has been optimized for linearizing M/A-COM’s AT10-0009 or AT10-0017 attenuators, but will function well with most types of cathode grounded, PIN attenuators. The driver is packaged in a SOW-16 package for commercial SMT applications. A typical schematic for a 30 dB, 7.5 dB/V linear attenuator is shown in Figure 1.
SOW-16
Package outline conforms to JEDEC standard MS-013AA
Circuit Description:
(Reference Figures 1 and 2)
The input divider, R1 and the sum of R2 and R3, sets the overall transfer function of the circuit. To increase the transfer function, decrease the Control Voltage and the value of R1. Varying the value of R4 will optimize the linearity of the circuit. One can achieve a very linear transfer function (<± 1 dB/V) by driving the attenuator over a smaller portion of its dynamic range. In the case of the AT10-0009 and AT10-0017 attenuators, this would be limited to a dynamic range of 28 and 25 dB, respectively. Temperature compensation is a function temperature coefficient of the thermistor, R3, and the ratio of R2 to R3, and can only be optimized once the transfer function and linearity component values have been established.
Figure 1
R1
Vcontrol (0 to 4V)
39K
R2 680
R3
(PTCT)
NOTES: TRANSFER FUNCTION IS 7.5 dB/V Vcontrol IS 0V to 4.0V +Vcc IS 5.0V ± 5% R3 IS A POSITIVE TEMPERATURE COEFFICIENT THERMISTOR ATTENUATOR IS AT10-0009 OR AT10-0017
4
3
330
R4 360
14
IN
DR65-0002
REF
5
+Vcc
C1
.01 µF
12
SCHEMATIC LINEAR ATTENUATOR
RFin
2
1,3,4
ATTENNUATOR
7
5,6,8 9,11,12
10
RFoutput
16,14,13
Linear Driver for PIN Diode Attenuators
Electrical Specifications, TA = +25°C, Reference Figure 1
Parameter Test Conditions Units Min Typical Max
Output Drive Current Load Dependent mA 10
+VCC Supply Range V 3.0 5.0 12
+VCC Supply Tolerance % 5
+VCC Quiescent Current No Load mA 1.0 2.0
Linearity Application Dependent dB ± 1 ± 2.5
Transfer Function Application Dependent dB/V 3 7.5 10
Settling Time 50% Ctl to 90%/10% RF µS 50
DR65-0002
V 4.00
Figure 2—Typical Attenuation Error
2
1.5
1
0.5
0
-0.5
Attenuation Error
-1
-1.5
-2
Frequency: 1960 MHz Vcont: 0 to 4.0V
DR65-0002 Driver with AT10-0017 Attenuator
0 3 6 9 12 15 18 21 24 27 30
LINEARITY ERROR
Attenuation (dB)
Pin Configuration
Pin # Function Pin # Function
1 N/C 9 N/C 2 N/C 10 N/C 3 REF 11 N/C 4 INPUT + 12 OUTPUT 5 GND 13 N/C 6 N/C 14 + V 7 N/C 15 N/C 8 N/C 16 N/C
CC
Absolute Maximum Ratings 1
Parameter Absolute Maximum
+V
CC
+20 V
Input + ± 5 V
REF ± 5 V
Output Current 20 mA
Operating Temperature -40ºC to +85ºC
Storage Temperature -65ºC to +125ºC
Package Power Dissipation 150 mW
Lead Temperature 300ºC for 10 seconds
1. Operation of this device above any one of these parameters may cause permanent damage.
Ordering Information
Part Number Package
DR65-0002 Bulk Packaging
DR65-0002TR Tape & Reel (1K Reel)
DR65-0002-TBG Test Board with Circuit per Figure 1
DR65-0002-TBP Test Board with Circuit per Figure 1
(AT10-0009, GSM Attenuator)
(AT10-0017, PCS Attenuator)
Specifications subject to change without notice.
n North America: Tel. (800) 366-2266 n Asia/Pacific: Tel.+81-44-844-8296, Fax +81-44-844-8298 n Europe: Tel. +44 (1344) 869 595, Fax+44 (1344) 300 020
Visit www.macom.com for additional data sheets and product information.
2
Loading...