MACOM DP52-0002-TR, DP52-0002 Datasheet

Low Cost SMT Dual Band Diplexer DP52-0002

g

DP52-0002

Low Cost SMT Dual Band Diplexer
824 – 960 / 1850 – 1990 MHz (AMPS/PCS)
880 – 960 / 1700 – 1900 MHz (GSM/DCS)

Features

• Small Size and Low Profile

• Industry Standard SOIC-8 SMT Plastic Package

• Superior Repeatability

• Passbands 824 - 960 MHz and 1850 - 1990 MHz

• Passbands 880 - 960 MHz and 1700 - 1900 MHz

• Typical Passband Insertion Loss: 0.5 dB

• 2 Watt Power Handling

• Low Cost

Description

M/A-COM’s DP52-0002 is an IC-based monolithic diplexer in a
low cost SOIC-8 SMT plastic package. This diplexer is ideally
suited for applications where small size, low insertion loss, supe­rior repeatability and low cost are required. Typical applications
include AMPS/PCS and GSM/DCS dual mode portable devices.

The DP52-0002 is fabricated using a passive-integrated circuit
process. The process features full-chip passivation for increased
performance and reliability.

SO-8

PIN 8

.1497-.1574

Orientation

mark

PIN 1

.004 (0.10)

.050(1.27) BSC.

.1890-.1968

(4.80-5.00)

- A -

(All dimensions per JEDEC No. MS-012-AA, Issue C)

Unless Otherwise Noted: .xxx = ± 0.010 (.xx = ± 0.25)

(3.80-4.00)

- B -

.0532-.0688

(1.35-1.75)

- C -

.0040-.0098

(0.10-0.25)

.013-.020 TYP.

(0.33-0.51)

.010(0.25) M C A M B S

8- Lead SOP outline dimensions

Narrow body .150

Dimensions in ( ) are in mm.

.2284-.2440

(5.80-6.20)

.010(0.25) M B M

.0099-0.0196

x 45° Chamfer

(0.25-0.50)

0°-8°

.016-.050

(0.40-1.27)

.0075-0.0098

(0.19-0.25)

.xx = ± 0.02 (.x = ±0.5)

Ordering Information

Part Number Package

DP52-0002
DP52-0002-TR

1. If specific reel size is required, consult factory for part number
assignment.

SOIC-8-Lead Plastic Packa
Forward Tape and Reel

1

e

824 - 960 / 1850 - 1990 MHz Typical Electrical Specifications1, TA= +25ºC

Parameters Units Min. Typ. Max.

Passband Insertion Loss dB — 0.5 0.8
Stopband Isolation dB 12 18 —
Passband VSWR — — 1.4:1 1.7:1

1. All specifications apply with a 50-ohm source and load impedance.

880 - 960 / 1700 - 1900 MHz Typical Electrical Specifications1, TA= +25ºC

Parameters Units Min. Typ. Max.

Passband Insertion Loss dB — 0.5 0.9
Stopband Isolation dB 12 18 —
Passband VSWR — — 1.5:1 1.8:1

1. All specifications apply with a 50-ohm source and load impedance.

M/A-COM Division of AMP Incorporated ■ North America: Tel. [phone], Fax [phone] ■ Asia/Pacific: Tel.[phone], Fax [phone]
Europe: Tel. [phone], Fax+ 44 (1344) 300 020

www.macom.com

AMP and Connecting at a Higher Level are trademark s.

Specifications subject to change without notice.

■

V2.00

Low Cost SMT Dual Band Diplexer DP52-0002

g

Absolute Maximum Ratings

1

Parameter Absolute Maximum

Input Power
Operating Temperature
Storage Temperature

2W CW

-40°C to +85°C

-65°C to 150°C

1. Exceeding these limits may cause permanent damage.

Recommended PCB Configuration

.072

.067
TYP.

AMPS IN/OUT

.244

∅.

016 PLATED

THRU (14X)

.113

.244

ANTENNA

PCS

.072

.030 TYP.

∅

.05 0 P LATED

THRU (2X)

Functional Diagram

ANTENNA

GND

8

LPF

1

GND

AMPS

IN/OUT

All unus ed pins mu st be R F an d D C grounded.

Pins 1 and 4 a re thermal

PCS
IN/OUT

GND

HPF

GND

GND

round contacts.

5

4

CIRCU IT MATERIAL: FR-4, .0 16 TH ICK.

Typical Performance @ +25°C

0

-5

-10

-15

-20

-25

INSERTION LOSS dB

-30

-35

-40

0 300 600 900 1200 1500 1800 2100 2400 2700 3000

FREQUENCY MHz

Antenna /
AMPS, GSM

Antenna /
PCS, DCS

AMPS / PCS
GSM/DCS

VSWR vs. FrequencyInsertion Loss vs. Frequency

3

2.75

2.5

2.25

2

VSWR

1.75

1.5

1.25

1

0 300 600 900 1200 1500 1800 2100 2400 2700 3000

FREQUENCY MHz

Antenna

AMPS, GSM

PCS, DCS

M/A-COM Division of AMP Incorporated ■ North America: Tel. [phone], Fax [phone] ■ Asia/Pacific: Tel.[phone], Fax [phone]
Europe: Tel. [phone], Fax+ 44 (1344) 300 020

www.macom.com

AMP and Connecting at a Higher Level are trademark s.

Specifications subject to change without notice.

V2.00

■