Maclocks Technology ML HBTIER1 User Manual

IMPORTANT SAFEGUARDS:

When using an electrical product, basic precautions should always be followed ,including the following: READ ALL INSTRUCTIONS BEFORE USING:

• THIS IS NOT A TOY. Not for use by children.

• Please do not attempt to change or remove the lithium battery yourself.

• Do not dispose of batteries in fire.

• Do not leave batteries in hot places such as an automobile under direct sunlight.

• Do not mix used and new batteries, or install used batteriesin other equipment.

• Do not mix Alkaline, Standard (Carbon-Zinc) or Rechargeable (Nickel Cadmium) or (Nickel Metal Hydride) batteries.

• Do not reverse the polarity (positive and negative terminals) of batteries.

FCC & IC

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

Made in China

QUICK START GUIDE

IN-EAR Bluetooth

HEADPHONES

Package Includes:

• Bluetooth Headphone

• Micro USB to USB Charging Cable

Please Read this Quick Start Guide before using the product, and save it for future ferences.

In-Ear Bluetooth Headphones

Product Description:

1. Ear Piece

2. Volume Down / Skip to Next Song

3. Power Button (on/o) / Pause/Play and Answer / Hang-Up Call

4. Volume Down / Previous Song

Ensuring a Good Fit:

To enjoy better sound quality and/or for a more comfortable t, change the size of the earbuds or adjust the earbud position to t snugly in your ears – do not force in. When you change the earbuds, turn them to install rmly on your headset and prevent the earbud from detaching and remaining in your ear.

How to place the headset on your ears:

1. Hang the neck band over the back of your ears.

2. Gently insert the earbuds into your ear ensuring a comfortable t.

3. Do the same for the other ear.

Note there is a small “L” and “R” on the earbuds indicating which ear the buds should go into.

Using your Bluetooth Headphones:

To turn on, long-press the Power Button for 3-5 seconds until a blue & red light appear and a voice comes on and says “Power On.” The LED Light will blink red & blue and the voice will say “Pairing.”

To Turn O, simply long-press the power button for 3-5 seconds. LED light will turn red.

For Pairing, see below for more details. To Answer a call: quickly press the center power button to accept the call.

To end the call, quickly press the power button once.

You can make a call by quickly pressing the power button twice – it will redial your last call.

To Pause / Play the music, simply tap the center power button quickly once.

To increase volume: tap the volume up button; to decrease volume, tap the volume down button.

To skip a song, long press the volume up and you’ll go to the next song.

To replay a song, long press the volume down button.

Bluetooth Pairing:

• On your mobile device please turn ON Bluetooth.

• Power up Bluetooth headphones by pressing and holding the power button.

• The LED light will ash red/blue.

• On your Bluetooth device select “BT_Headphones.”

• Will hear “pairing successful” - you are now paired!

Charging the battery:

• Charging the headset by USB charging cable (included in the package).

• The LED lamp is lit red while the battery is charged.

• The LED lamp is lit blue when the battery is fully charged.

• It takes around 25 minutes to fully charge the battery.

1. Connect the USB charging cable to the unit.

2. Connect the USB charging cable to your PC or USB wall charger.

* when the battery is low, a beeping alarm will sound, and the LED light will blink red. After a while, product will turn o.

Battery Information:

• Do not leave a fully charged battery connected to a charger; overcharging may shorten the battery life.

• If left unused a fully charged battery will lose its charge over time.

• Never use any charger that is damaged.

• Never leave the device in excess heat.

§ 15.19 Labelling requirements.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

§ 15.21 Information to user.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

§ 15.105 Information to the user. Note: This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

* RF warning for Portable device:

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.



