Lynx LX-218S User Manual

Lynx Pro Audio S.L.

Valencia, Spain - www.lynxproaudio.com - [e-mail]

USER MANUAL

V.10.13

LX-218S

V.13.10

This user manual is property of Lynx Pro Audio S.L. Any reproduction of this manual, by any means is strictly prohibited.
Copyright 2013. All rights reserved.

Manufacturer

CB SCHEME, IEC SYSTEM FOR CONFORMITY TESTING AND CERTIFICATION
OF ELECTRICAL EQUIPMENT

CE CERTIFICACTION, EUROPEAN PRODUCT

LX-218S powered cabinet

LYNX Pro Audio S.L.
Calle 7 - Pol. Ind. Picassent
E-46220 Picassent (Valencia)

RoHS Directive 2002/95/EC

CONTENTS

- SAFETY PRECAUTIONS

- CABINET INTRO

SPECIFICATIONS 5
BACK PANEL 6
CONNECTORS AND CONNECTIONS 6

- CONFIGURING THE CABINET DSP OPTIONS

CONFIGURATION PANEL 8
SELECT INPUT DIGITAL / ANALOG 8
SELECT AND RUN PRESETS 9
PRESET LIST 10
CARDIOID CONFIGURATION 11
ONLINE CONTROL SYSTEM 19
ETHERNET CONFIGURATION 20

- SOFTWARE, RAINBOW 26

- ACCESSORIES 28

- GUARANTEE 29

- DECLARATION OF CONFORMITY CE 30

Before starting to use this device, please read this instruction manual carefully.
Keep these instructions in the place where the equipment will be used and with easy access to them.

- Electrical appliance.

The exclamation mark within a triangle identifies the presence of electricity. Use the system carefully without
wet hands or feet. Avoid installing the speaker in wet or excesivelly humid places. Regularly check the condition
of the cables and make sure these are not being walked on or pinched. Connect the speaker to bipolar, earthed
mains. The mains plug must be connected to the appropriate protection (fuse or breaker). Connection to any
other type of mains could result in an electrical shock and violate local electrical codes. DO NOT CONNECT OR
DISCONNECT THE AC POWER CONNECTORS UNDER LOAD.

- Heavy equipment.

Apply back protection when using the system. Avoid loading and unloading at heights.

- Electrical shock risk.

The diagonal mark within a triangle identifies the presence of dangerous voltage.
Do not open or handle the interior of the box. These parts are not to be adjusted by the user. For maintenance
and/or repair please go to an authorized service centre.
In order to reduce the risk of electric shock, disconnect from AC before plug in or unplugging Audio signal
cables. Reconnect to AC only if all signal connections are made and secured.
Never manipulate the ground type plug provided.
The AC mains plugs should always remain accessible for operation.
Unplug the loudspeaker during storms or when it’s being used for a long time.

- Hearing damage risk.

These systems can reproduce large quantities of sound pressure which can damage hearing. Take precautions
if you are going to be near them for extended amounts of time and do not get too close.

- Hanging – Flying.

Do not hang the cabinets from the handles or from any other part other than the designated hanging point.
When flying this system please observe the technical and “Rainbow” software data carefully. Never exceed the
maximum safe working loads or ignore the instructions included within this manual. Use Only flying accessories
provided by Lynx Pro Audio S.L.
Rigging must be always carried out by professionals.

- Delicate Material.

Please ensure no foreign object or water enters the speaker. Do not place material that contains liquid on or near
the unit. Only clean the unit with dry cloths. Do not use solvents.

-Overheating – Fire risk.

To reduce the risk of the speaker over heating, avoid direct contact with sunlight. Avoid placing the unit close
to heat inducing objects such as radiators. Do not cover the equipment in use and do not block any ventilation
openings. Do not put naked flame, such as lighted candles, close or on top of the unit.

- Electromagnetic and interferente emissions.

Avoid placing objects which through electromagnetic waves can damage the unit, such as mobile phones, lap
tops, magnetic strip cards etc.

This system complies with normatives EN 55103-1 (1)

EN 55103-2 (2)

(1) This device may not cause harmful interferences.
(2) This device may receive interference including interferences that may cause undesired working.

-IMPORTANT NOTE.

This Equipment must be used in accordance with these instructions and by trained professional personnel
only.
This equipment should not be used in places with extreme tropical climates. Don’t expose this apparatus to
extreme humidity and or temperature values.

LX-218S

LYNX Pro Audio S.L. - Valencia, Spain - www.lynxproaudio.com [e-mail]

SPECIFICATIONS:

FREQUENCY RANGE 30Hz -200Hz
FREQUENCY RESPONSE 35Hz- 125Hz ± 3dB

HORIZONTAL COVERAGE 360º single unit
MAX SPL 136 dB/ 139dB peak

TRANSDUCERS LF: 2 x 18" Custom

Nomex Cone and Neodimium magnet
SHAPE Direct radiation
POWER AMPLIFIER 3000W Class D with Switching Power supply

2 x 1500W
DSP Internal LYNX digital processor DSPB-22®
CABINET ADJUSTMENT Back panel LCD screen
INTERNAL CONTROLS Temperature sensor / Fan Speed
SIGNAL CONNECTION NEUTRIK connectors XLR Male Input

XLR Female Loop Thru
CONTROL CONECTIONS USB (DSP programming),

ETHERNET* (Online Monitoring System OMS®)
AC POWER 230v / 115v selectable. 50/60 Hz 3A
AC CONECTIONS 16A NEUTRIK POWERCON with Looping Output
CONSTRUCTION 21 mm Premium birch plywood
FINISH High resistant water-based black paint
FRONT DESIGN Black steel grille

DIMENSIONS (H x W x D) 532 x 1080 x 700 mm
WEIGHT 72 Kg (158 lbs)

INTRODUCTION

To facilitate, correct and reliable use of the Lynx LX-218S we have designed this instruction manual. Please read the
manual carefully before proceeding to install the system.

When flying this system please observe the technical and “Rainbow” software data carefully. Never exceed the
maximum safe working loads or ignore the instructions included within this manual.

5

* Ethernet is optional

LYNX Pro Audio S.L. - Valencia, Spain - www.lynxproaudio.com [e-mail]

LX-218S

LX-218S BACK PANEL.-

12 5

6 43

1.- SIGNAL INPUT.

2.- SIGNAL LINK.

3.- INPUT AC.

4.- AC LINK (máx. +1 cabinets).

5.- USB.

6.- DSP CONTROL.

CONNECTORS AND CONNECTIONS

XLR AEREAL CONNECTORS

Connect to output

Connect to input

2 Live(+)

3 Live(-)

1 Earth

3 Live(-)

1 Earth
2 Live(+)

OUTPUTS

1.- EARTH

2.- LIVE (+)

3.- LIVE (-)

1

3

2

INPUTS

1.- EARTH

2.- LIVE (+)

3.- LIVE (-)

2

3

1

XLR SOCKET CONNECTORS

6

LX-218S

LYNX Pro Audio S.L. - Valencia, Spain - www.lynxproaudio.com [e-mail]

Connect to AC output
(max.2 cabinets)

Connect to signal
output

CONNECTION EXAMPLE: 4 LX-218S CABINETS

Connect to AC output
(max.2 cabinets)

SOCKET POWERCON CONNECTORS

CAUTION: Do not connect or
disconnect the AC Power
connectors under load.

L - Line
N - Neutral

- Earth

7

LYNX Pro Audio S.L. - Valencia, Spain - www.lynxproaudio.com [e-mail]

LX-218S

CONFIGURING THE CABINETS DSP OPTIONS

From the buttons below the display on the Lynx cabinet’s back panel you are able to configure the Basic

adjustment functions of the internal DSP.
Note:

You must apply the desired configuration in each cabinet. This is done via the buttons located on the back
panel of the cabinet and requires electrical power to work.

CONFIGURATION PANEL

On the back panel you will see 3 buttons and an information screen, on which you can read the established
parameters and information such as input mode (analog or digital), amplification module temperature, input signal
level and name of the current preset (Fig1). If changes are not made the display will automatically dim to save
energy and avoid unnecessary light in situations where light is not wanted. To re-activate the light simply press
the OK button.

8

SELECT THE INPUT: DIGITAL OR ANALOG

There are four input options: Analog / Digital L / Digital R / Digital L+R
To select the input mode just press the OK button (3) and keep pressing down whilst at the same time you press

the up button (1). One of the four options will appear on the screen. Then you can use the up button (1) to search
the option required. To confirm your selection press OK (3) until the progress bar finishes. The display will show an
inverted D (digital) or an inverted A (Analog) so you can always know if the input is digital or analog.

1

2

3

Fig 1

LX-218S

LYNX Pro Audio S.L. - Valencia, Spain - www.lynxproaudio.com [e-mail]

Fig 3 Fig 4

Note:
In case of a power cut, the DSP will save its last configuration when restarted.

9

SELECT AND RUN PRESETS

To change the preset configuration just press the up button (1) and down button (2) until you see the title
and preset number required (Fig2). Once found, press OK (3) until the progress bar finishes (Fig3). The display will
indicate “Loading DSP” (Fig4)

Fig 2

LYNX Pro Audio S.L. - Valencia, Spain - www.lynxproaudio.com [e-mail]

LX-218S

PRESET LIST

From the buttons below the display on the cabinet’s back panel you are able to configure the Basic adjustment
functions of the internal DSP. Depending on the model, you can find the following configurations:

Note:
You must apply the desired configuration in each one cabinet. This is done via the buttons located on the back panel
of the cabinet and requires electrical power to work.

10

LX-218S

LYNX Pro Audio S.L. - Valencia, Spain - www.lynxproaudio.com [e-mail]

11

CARDIOID CONFIGURATIONS

Mode 1:

- For A cabinets use preset 10

- For B cabinets use preset 11

- With this configuration we obtain around 24 dB of attenuation between 30Hz
and 100Hz, and between 1 and 1.5 dB more SPL up front.

A

A

B

20 30

40

50 60

70

80

90 100

(Hz)

0

-3

-6

-9

-12

-15

-18

-21

+3

+6

+9

(dBr)

Mode 1: Front

Mode 1: Rear
Normal Mode: Front
Normal Mode: Rear

Image 1: Polar response for Mode 1 at 60 Hz Image 2: Polar response at 60 Hz (2 cabinets)

Graphic 1: Mode 1 vs. Normal Mode

LYNX Pro Audio S.L. - Valencia, Spain - www.lynxproaudio.com [e-mail]

LX-218S

12

CARDIOID CONFIGURATIONS

Mode 2:

- For A cabinets use preset 10

- For B cabinets use preset 12

- With this configuration we obtain around 24 dB of attenuation between 30Hz
and 100Hz, and between 1 and 1.5 dB more SPL up front.

A

B

A

20 30

40

50 60

70 80 90 100

(Hz)

0

-3

-6

-9

-12

-15

-18

-21

+3

+6

+9

(dBr)

Mode 2: Front
Mode 2: Rear
Normal Mode: Front
Normal Mode: Rear

Image 3: Polar response for Mode 2 at 60 Hz

Image 4: Polar response at 60 Hz (2 cabinets)

Graphic 2: Mode 2 vs. Normal Mode

LX-218S

LYNX Pro Audio S.L. - Valencia, Spain - www.lynxproaudio.com [e-mail]

13

CARDIOID CONFIGURATIONS

Mode 3:

- For A cabinets use preset 10

- For B cabinets use preset 13

- With this configuration we obtain around 23 dB of attenuation between 30Hz
and 100Hz, and between 1 and 1.5 dB more SPL up front.

B

A

A

20 30

40

50 60

70

80

90 100

(Hz)

0

-3

-6

-9

-12

-15

-18

-21

+3

+6

+9

(dBr)

Mode 3: Front

Mode 3: Rear
Normal Mode: Front
Normal Mode: Rear

Image 5: Polar response for Mode 3 at 60 Hz

Image 6: Polar response at 60 Hz (2 cabinets)

Graphic 3: Mode 3 vs. Normal Mode

LYNX Pro Audio S.L. - Valencia, Spain - www.lynxproaudio.com [e-mail]

LX-218S

14

CARDIOID CONFIGURATIONS

Mode 4:

- For A cabinets use preset 10

- For B cabinets use preset 14

- With this configuration we obtain around 23 dB of attenuation between 30Hz
and 100Hz, and between 1 and 1.5 dB more SPL up front.

A

B

20 30

40

50 60

70

80

90 100

(Hz)

0

-3

-6

-9

-12

-15

-18

-21

+3

+6

+9

(dBr)

Mode 4: Front

Mode 4: Rear
Normal Mode: Front
Normal Mode: Rear

Image 7: Polar response for Mode 4 at 60 Hz

Image 8: Polar response at 60 Hz (2 cabinets)

Graphic 4: Mode 4 vs. Normal Mode

LX-218S

LYNX Pro Audio S.L. - Valencia, Spain - www.lynxproaudio.com [e-mail]

15

CARDIOID CONFIGURATIONS

Mode 5:

- For A cabinets use preset 10

- For B cabinets use preset 15

- With this configuration we obtain around 23 dB of attenuation between 30Hz
and 100Hz, and between 1 and 1.5 dB more SPL up front.

B

A

20 30

40

50 60

70

80

90 100

(Hz)

0

-3

-6

-9

-12

-15

-18

-21

+3

+6

+9

(dBr)

Mode 5: Front

Mode 5: Rear
Normal Mode: Front
Normal Mode: Rear

Image 9: Polar response for Mode 5 at 60 Hz

Image 10: Polar response at 60 Hz (1 cabinet)

Graphic 5: Mode 5 vs. Normal Mode

LYNX Pro Audio S.L. - Valencia, Spain - www.lynxproaudio.com [e-mail]

LX-218S

16

CARDIOID CONFIGURATIONS

Mode 6:

- For A cabinets use preset 10

- For B cabinets use preset 16

- With this configuration we obtain around
24 dB of attenuation between 30Hz and
100Hz, and between 1 and 1.5 dB more
SPL up front.

A B A

20 30

40

50 60

70

80

90 100

(Hz)

0

-3

-6

-9

-12

-15

-18

-21

+3

+6

+9

(dBr)

Mode 6: Front
Mode 6: Rear
Normal Mode: Front
Normal Mode: Rear

Image 11 Polar response for Mode 6 at 60 Hz

Image 12: Polar response at 60 Hz (2 cabinets)

Graphic 6: Mode 6 vs. Normal Mode

LX-218S

LYNX Pro Audio S.L. - Valencia, Spain - www.lynxproaudio.com [e-mail]

17

CARDIOID CONFIGURATIONS

Mode 7:

- For A cabinets use preset 10

- For B cabinets use preset 17

- With this configuration we obtain between
15 and 28 dB of attenuation from 30Hz to
100Hz, and between 1 and 2 dB more SPL
up front.

B A

20 30

40

50 60 70 80 90 100

(Hz)

0

-3

-6

-9

-12

-15

-18

-21

+3

+6

+9

(dBr)

Mode 7: Front

Mode 7: Rear
Normal Mode: Front
Normal Mode: Rear

Image 13: Polar response for Mode 7 at 60 Hz

Image 14: Polar response at 60 Hz (1 cabinets)

Graphic 7: Mode 7 vs. Normal Mode

LYNX Pro Audio S.L. - Valencia, Spain - www.lynxproaudio.com [e-mail]

LX-218S

18

NOTES:

- All measurements have been taken in the open air.

- Measurements carried out in “Half Space”.

- In a closed room the response can vary depending on distance between walls, ceiling etc.

- The graphs are shown in relative dB measurements.

- The polar responses are shown in dB SPL obtained from acoustic prediction.

LX-218S

LYNX Pro Audio S.L. - Valencia, Spain - www.lynxproaudio.com [e-mail]

19

ONLINE CONTROL SYSTEM

Who is it for?

Users of Self powered DSP incorporated Lynx Pro Audio Cabinets where the user has requested the cabinets be
supplied with the Ethernet Module kit.

What is it for?

Obtain detailed information of cabinet behaviour and monitor the cabinet/s in real time. You can change the
preset, gain, mute, polarity and phase. You can also activate the air absorption compensation and select the
«SOLO» mode.

How does it work?

Via Ethernet (cable or wireless). Once installed, the O.C.S. software automatically detects all the cabinets
connected to the network and displays them in the O.C.S. window on the users PC.

What does it show?

As well as displaying the cabinet model and IP address the O.C.S will be monitoring in real time and the user will
be able to view RMS levels, Input clip, power module temperature, compression levels, air absorption
compensation and cabinet angulation.

LYNX Pro Audio S.L. - Valencia, Spain - www.lynxproaudio.com [e-mail]

LX-218S

CONFIGURING ETHERNET TO WORK WITH LX-218S

There are two possible ways to connect:

1.- Connecting through an ETHERNET SWITCH/HUB::

- You will need a normal CAT5 Cable.

2.- Connecting through a Wirless ETHERNET.

Let us now proceed to configure the Ethernet network, setting the IP address of the computer as static.
To do this go to:

START > CONFIGURATION > NETWORK CONFIGURATION

We will launch the properties of "Local Area
Connection" by clicking the right mouse but­ton and clicking on properties.

20

LX-218S

LYNX Pro Audio S.L. - Valencia, Spain - www.lynxproaudio.com [e-mail]

Select "Internet Protocol (TCP / IP)" and click on
properties.

Select: “Use next IP Address” And write as you
wish, in order to configure your network.

Normally, Ip values will be something like this:

IP Address: 192.168.1.xxx
Subnet Mask: 255.255.255.0

Where xxx will be a number between 1 and 254
Accept to quit the network settings and again to

apply them at the next screen. Depending on the
Windows Version, you will be asked to reboot or
not.

Once the Computer is configured with a static IP
proceed to connect to the line array system through
the O.M.S. (online monitoring system) software.

Open the OCS software and from the Initial Screen
choose Ethernet device into the configuration menu.

It will open a different screen, as follows, there you can see your Network configuration, and the cabinets currently
connected.

21

LYNX Pro Audio S.L. - Valencia, Spain - www.lynxproaudio.com [e-mail]

LX-218S

If you want to change the IP select the cabinet and modify the assigned IP in order to be able to connect to it.

By default, the Cabinet will have this IP 192.168.2.100

The Network enviroment consists in the first 3 sets of three numbers separated by dots. In order to detect/communicate
with the cabinets, the software and the cabinets must have the same Network settings.

If it is not in the same environment Windows Profesional (2000, XP, VISTA, Windows 7 and 8) will detect it, but is not
going to be able to establish connection. In Windows Home, the processor is not going to be detected until the same
enviroment is applied.

In order to change the IP settings to have the same configuration as the PC, we can change the IP address of the
cabinets by clicking in the Assign IP to select Device button after writing in the box above the desired data. Remember
there cannot be two devices with exactly the same IP address, the last set of three numbers has to be different and
unique to each one of the devices.

22

LX-218S

LYNX Pro Audio S.L. - Valencia, Spain - www.lynxproaudio.com [e-mail]

for example, write 192.168.1.100 and click "Change Device IP" button.
The OCS software will send the new IP to the cabinet and it will scan the network again showing the same information

as before, plus more information such as Pc name, IP address and Port in which the communication is established.

When we have a lot of cabinets connected in the network we can use the button “Identify Device” to see which box
is selected (two activity LEDS will blink for one second). With that information then we can “Change device NAME”
assigned to this Cabinet by clicking in the “Change device name” button after writing in the box above the desired
Name.

Returning to the main screen, we can see each cabinet showing: Model, IP address and Name, as well as monitoring:
RMS levels, Input clip, power module temperature, compression levels, air absorption compensation and cabinet
angulation, as well as displaying the cabinet model and IP address.

23

LYNX Pro Audio S.L. - Valencia, Spain - www.lynxproaudio.com [e-mail]

LX-218S

If you need to know the PC Network settings go to:

START > ALL PROGRAMS > ACCESSORIES > Command Prompt

It will open the cmd.exe from where you can type the IPCONFIG command ( ipconfig + Enter), which will show your actual IP
settings.

Here we can see that this PC has IP set as 192.168.2.99.

24

LX-218S

LYNX Pro Audio S.L. - Valencia, Spain - www.lynxproaudio.com [e-mail]

You can also use the command promt to know if an IP is already in use by another device. In this case type "ping
IP" (ping 192.168.2.xxx) and press enter. If there is no device with this IP you will see the following information:

If the IP is in use, the device will respond to the Ping, and we will obtain this information:

You now have the Cabinets working in the ETHERNET Network Enviroment.

25

LYNX Pro Audio S.L. - Valencia, Spain - www.lynxproaudio.com [e-mail]

LX-218S

RAINBOW – ACOUSTICAL PREDICTION SOFTWARE

Thanks to the RAINBOW software, you will be able to “virtually” determine the acoustical response of one or
various cabinets at the same time.

Based on polar response measurements, taken
meticulously with a 360º coverage both vertically
and horizontally, the Rainbow software is able to
calculate the SPL response including the
interaction between them taking into account the
magnitude and phase response, in order to enable
the user to correct cancellations and even to
create them if the acoustical design so requires.

Rainbow is very easy to use and offers a very
intuitive design, multitool interface and on-line
updatable data base.

The Rainbow software has been designed by and
for sound technicians. Its aim is to help installers
and users of Lynx pro audio products.

This software is able to import WMF Vector Files
with technical drawings and insert them directly
into the prediction window and thus enabling real
measurement predictions.

This also helps to determine dead zones and
obtain the maximum performance from each of the
cabinets installed.

26

LX-218S

LYNX Pro Audio S.L. - Valencia, Spain - www.lynxproaudio.com [e-mail]

Features

The RAINBOW acoustical prediction software allows among other things:

- Prediction up to 4 LINE ARRAYS of 24 cabinets each simultaneously, together with multiple points
with cabinets

- Flying points information according to the inclination of the cabinets

- Weight calculation of the different systems

- Sub-bass simulation (for instance to achieve cardiod configurations)

- Orientation of cabinets (Horizontal/vertical)

- Throw Direction of cabinets (right/ left)

- Individual delay per cabinet/system

- Polarity selection for each cabinet

- Up to 40 process insertions with Equalization and CrossOver assignable per cabinet.

- Simulation of the Air absorption sound loss with the distance

- SPL Pressure information

- Distance measurement

- Import of CAD files

- Up to 4 audience or hearing zones

- Coverage curves on the hearing zones.

- Export of SPL Map and coverage curves on jpg or bmp format

- Print project report (SPL prediction, flying points, weights, cabinet inclination, polarities, process
aplied, EQ Curves…)

27

LYNX Pro Audio S.L. - Valencia, Spain - www.lynxproaudio.com [e-mail]

LX-218S

ACCESSORIES

The LX-218S sub unit has at its disposal some practical accessories to help use the system in a number of
applications.

FD-2LX218S
FD-3LX218S

Nylon protection cover for
either 2 or 3 cabinets

FD-1LX218NL

Rain cover for the back
pannel

CA-LXV8

Transport dolly for up to 3
LX-218S

STK-218

Adaptor to stack
ADP-215 over vertical
LX-218S

28

LX-218S

LYNX Pro Audio S.L. - Valencia, Spain - www.lynxproaudio.com [e-mail]

LYNX PRO AUDIO GUARANTEE

Lynx products are guaranteed against every kind of manufacturing fault 2 year after the date of sale. When
products are under guarantee, the repairing and the free supplying of the device parts in order to correct any kind
of defect are guaranteed by Lynx Pro Audio S.L. In the case that the product could not be returned to the factory
for checking and repairing, Lynx Pro Audio S.L. would supply all the necessary parts.

Lynx Pro Audio S.L. is not responsible for any damage or defect caused during the transport or caused by an
undue or improper handling y a non-authorized person during the life of this guarantee.

All our products undergo rigorous tests and quality controls. We guarantee the characteristics described here within
and their quality against any fabrication defect.

The user loses all warranty rights if he incorporates or carries out any modification to the product, if he uses it outside
of the stated safe working loads or does not secure the system properly using all the pins in their corresponding
holes.

For any question regarding the product, the user must quote the model and serial number.

29

DECLARATION OF CONFORMITY

LYNX Pro Audio S.L.

Calle 7 - Pol. Ind. Picassent

E-46220 Picassent (Valencia)

Lynx Pro Audio S.L. declares that LX-218S cabinets are in conformity with the following EC directives:
Low Voltage Directive 2006/95/EC

Electromagnetic Compatibility EMC 2004/108/EC
RoHS Directive 2002/95/EC

In accordance with Harmonized European Norms:
EN 60065:2002 Audio, video and similar electronic apparatus. Safety requirements
EN 55103-1:1996 Electromagnetic compatibility. Product family standard for audio, video, audiovisual

and entertainment lighting control apparatus for professional use. Part 1: Emission.

EN 55103-2:1996 Electromagnetic compatibility. Product family standard for audio, video, audiovisual

and entertainment lighting control apparatus for professional use. Part 2: Immunity.

WEEE Declaration: Electrical and electronic equipment must be disposed of separately from normal waste at the
end of its operational lifetime. Please dispose of this product according to the respective national regulations or
contractual agreements. If there are any further questions concerning the disposal of this product please contact
Lynx Pro Audio S.L.