Lynx LCS30F User Manual
MAKE THE MOST OF YOUR
LCS30 shown with pass shelf (LCSPS) which is available separately from Lynx Grills.
LCS30 COCKTAIL STATION
CARE & USE/INSTALLATION
LCS30 COCKTAIL STATION CARE & USE/INSTALLATION
1
|
EXTERIOR DIMENSIONS
INSTALLATION PREPARATION
INSTALLER: Read these instructions carefully before starting installation. Please leave these instructions with
the homeowner.
HOMEOWNER: Please retain these instructions for future use
Cutout Dimensions Exterior Dimensions
Cut-out Dimension
Width A Height B Depth C Width D Depth E Depth F
Specifications
LCS30 29 10½ 22 31 251/
Counter top notch detail: a 1/2” width is required
with a depth equal to the counter top overhang.
8
F
E
221/
D
8
Exterior DimensionsCutout Dimensions
The Lynx sinks are designed for outdoor use. It is recommended that the sink be installed by a qualied technician
in accordance with all local plumbing and building codes.
Prepare the counter top by cung the appropriate cutout dimensions from the table above. There must be a
minimum of a 1/2” overlap on the sides and rear of the sink on the counter top to support the sink. Adequate
clearances below the sink must be maintained for maintenance, water, and drain lines.
LCS30 COCKTAIL STATION CARE & USE/INSTALLATION
3
|
INSTALLING THE DRAIN ASSEMBLY
INSTALLING THE DRAIN ASSEMBLY
2. Remove the drain plug strainer basket (a) and separate the upper drain ng (b) from the remainder of the
drain assembly.
3. Place a bead of Plumbers Puy* around the underside lip of the upper drain ng. Drop the upper drain ng
(b) into the sink boom opening and press it rmly into place. From the boom of the sink posion the rubber
gasket (c) and then the paper gasket (d) on the upper drain ng (b). The paper gasket (d) is used to prevent
kinking of the rubber gasket (c) while ghtening the locknut (e).
4. Align the drain assembly so that it sits centered in the sink drain cut-out. Screw the locknut (e) on to the upper
drain ng (b) threaded connecon unl it is hand ght. Now use a tool to ghten the locknut (e) another
quarter turn.
5. Remove any excess Plumber Puy with a damp cloth.
* Plumbers Puy is available at most home improvement centers. Plumbers puy is an
easy-to-mold seng compound for use with stainless steel sealing applicaons. Do Not Omit This Step.
For ease of installaon we recommend that the drain assembly be installed before installing the sink into the counter
top.
1. Remove the drain assembly from the box and idenfy the following parts:
a. Drain Plug/Strainer Basket
Sink Boom
Sink Opening
b. Upper Drain Fing
c. Rubber Gasket
d. Paper Gasket
e. Locknut
f. Tailpiece
g. Threaded Coupling
LCS30 COCKTAIL STATION CARE & USE/INSTALLATION4
|
1. Install the faucet or the stainless steel plug (included) into the top faucet opening.
INSTALLING THE SINK
INSTALLING THE DRAIN PIPING (NOT SUPPLIED)
INSTALLING THE TRANSFORMER
2. Carefully lower the sink into the cut out on the counter top. Push the sink back unl there are no gaps in the
back and the bullnose contacts the front face of the cabinet. The sink will be supported by its weight on the side
and back.
3. If desired a small bead of silicone sealant could be put around the edges of the sink to prevent water seepage
into the spaces below the sink.
Faucet installation
instructions available
in the faucet box.
Assemble all drain pipe connecons to the tailpiece and on through a pipe trap and proper drainage. The drain
must be installed in accordance with all local codes. In the absence of local codes, the requirements of the Uniform
Plumbing Code should be followed.
The power supply transformer should be installed below the sink within the cabinet enclosure. Select a locaon
where the transformer is protected against water, heat and physical damage. It is recommended that fasteners are
used in at least two of the four mounng holes for secure aachment.
The power supply transformer must be plugged into a properly grounded GFI equipped outlet, installed by a
qualied technician. The outlet of the transformer is plugged into the white Molex connector at the rear of the sink.
Please see the electrical diagram provided in this manual.
LCS30 COCKTAIL STATION CARE & USE/INSTALLATION
5
|
INSTALLING THE LCS30 FRONT COMPONENTS
1. Located the supplied hardware bag with 3 stainless shoulder screws and 2 stainless philips head screws.
2. Install the two stainless steel shoulder screws into the right hand side inserts of the front panel.
3. Carefully lower the bole holder on the newly aached shoulder screws.
4. When installing the bole opener you will need to Install the third shoulder screw directly below the far le
insert. Aach the top of the bole holder when you install the towel bar, as they share the screw.
5. Connue to install the towel bar using the second stainless steel phillips head screw provided.
Stainless
Steel
Screws
Stainless Steel Shoulder Screws
LCS30 COCKTAIL STATION CARE & USE/INSTALLATION6
|
Loading...