LYNX COCKTAIL PRO
INSTALLATION AND ASSEMBLY INSTRUCTIONS
Model CS30F Shown
With Top Mounted Pass Shelf
Models: Description:
CS30-1
CS30F-1
Counter top unit with cold water faucet and sink assembly including
water filter, ice bin, bottle well holder with inserts, speed rail, bottle
opener with catch pan, towel holder and
LED lighting on the front panel
Free-Standing model with stainless steel cart, four casters, two
stainless steel doors, storage areas, cold water faucet and sink
assembly including water filter, ice bin, bottle well holder with inserts,
speed rail, bottle opener with catch pan, towel holder, LED lighting on
the front panel and optional (CSPS) top-mounted Pass Shelf with
condiment trays and halogen lighting (2008 and older models only)
CSPS
Note to Installer: Please leave these instructions with the homeowner
Note to Homeowner: Please keep these instructions for future reference.
P/N32024
Installation Instructions CS30-1 and CS30F-1
• Remove any protective wrapping
• Remove the speed rail, ice bin cover, bottle cap holder, faucet and water filter
assemblies, water filter holder and cutting board from the inside of the ice bin
• Assemble the faucet assembly and place into the mounting hole at the rear of the
sink and secure it in place with the lock nuts provided
• Position the cocktail pro CS30-1 in the island cutout (Does not apply to the
CS30F)
• Install a PVC drain line to the 1½” brass drain of the ice bin and sink. These may
be connected to single drain. Extend the drain line through the back of the island,
or out of the lower rear panel of the CS30F-1.
• Locate a convenient place below the CS30-1 and mount the water filter holder,
attach the flexible water tubing to the faucet inlet. Key lock studs are provided in
the cabinet below the CS30F-1 to mount the water filter holder
• Install the cold water line to the inlet side of the water filter or a garden hose may
be used.
• Once in place the CS30-1 cocktail pro can be sealed to the counter top using
clear, all-weather silicone sealant
• Remove protective wrapping from the speed rail, bottle cap holder, ice-bin cover
and cutting board
• Hang the speed rail and bottle cap holder from the front of the cocktail pro using
the key-lock studs
• Place the two piece sliding ice bin cover on the ice bin rail and place the cutting
board on the front of the sink’s drain board
• To install the Pass Shelf refer to the instructions accompanying the assembly
Electrical Requirements for CS30-1 and CS30F-1
WARNING: Electrical Grounding Instructions:
This outdoor appliance is equipped with a three-pronged (grounding) plug for
your protection against shock hazard and should be plugged directly into a
properly grounded three-prong outlet. Do not cut or remove the third prong from
this plug.
• Installation must include an outdoor rated, 120 VAC, 15 amp Ground Fault
Interrupter (GFI) electric outlet located adjacent to the appliance. A qualified
electrician should install a GFI outlet either inside the built-in enclosure or near
the normally used location for the free standing units.
• Free standing units may be plugged directly to a GFI protected outlet, built-in
units must have the 12 V transformer installed during installation.
• The transformer connection on the CS30-1 built-in model is located at the left
rear of the Cocktail Pro frame
The transformer must be installed in a dry location
Parts List for CS30-1 and CS30F-1
Part Number COCKTAIL PRO
80282 CS30 Body Assembly
80348 LED Light Assembly
32246 Front Panel
80356 Speed Rail
80359 Bottle Well Assembly
80357 Bottle Cap Catcher used with L10003 Bottle Opener
31663 Towel Ring used with 31662 Towel Ring Center Hub
80358 Sliding Cover Frame
30253 Sliding Cover Top Section used with 10165 Handle
30252 Sliding Cover Bottom Section
32614 Drain Kit
13043 Faucet
20001 Cutting Board
13004 Water Filter Housing
13035 Water Filter Cartridge
80360 Light Switch Harness
32113 Transformer, Single Power
80350 Cabinet CS30 2008 Model Year
80354 Pass Shelf Assembly
80351 Pass Shelf Left Bracket
80352 Pass Shelf Right Bracket
80355 Condiment Tray
80353 Pass Shelf Halogen Light Assembly
Notes
Notes
Limited Lifetime Warranty
Lynx warrants that the stainless steel housing will be free from defects in material and
workmanship when subjected to normal domestic use and service for the lifetime of the
original purchaser. This warranty excludes surface corrosion, scratches, and
discoloration which may occur during regular use.
This warranty does not apply to damage resulting from misuse, abuse, alteration,
accident, hostile environments, improper installation or installation code violations.
Limited Five Year Warranty
Lynx warrants the structural integrity of the interior and exterior body parts for 5 years
from the date of purchase. This warranty is limited to replacement of the
component/part if deterioration occurs to the point of non-performance. Replacement
parts are shipped F.O.B. from Lynx Professional Grills, Commerce, CA. Lynx is not
responsible for transportation costs, export duties or installation costs.
Limited One Year Warranty
Lynx warrants all other components to the original purchaser to be free from factory
defects in material and workmanship for one year from the original date of purchase.
Limitations
Lynx Professional Grills shall not be liable for incidental, consequential, special or
contingent damages resulting from its breach of this written warranty or any implied
warranty. This warranty applies only to the original purchaser and may not be
transferred.
Replacement parts will be provided in accordance with the above warranty with the
owner paying all other costs. Labor costs are covered for the first year of ownership only.
This warranty is in lieu of all other warranties, expressed or implied or any other
obligations or liabilities in connection with the sale of this appliance.
Some states do not allow limitations on how long an implied warranty lasts, or the
exclusions of, or limitations to consequential damages. This warranty gives you specific
legal rights, and other rights that vary from state to state.
Replacement parts may be obtained from the manufacturer by calling the technical
support center at 888-289-5969. Be sure to provide model number and serial number
and proof of purchase for any warranty claims.
Loading...