Information in this document is subject to change without
notice. No part of this document may be reproduced or
transmitted in any form or by any means, electronic or
mechanical for any purpose, without express written permission
of LYNX Technik AG.
LYNX Technik AG may have patents, patent applications,
trademarks, copyrights or other intellectual property rights
covering the subject matter in this document. Except as
expressly written by LYNX Technik AG, the furnishing of this
document does not give you any license to patents,
trademarks, copyrights or other intellectual property of LYNX
Technik AG or any of its affiliates.
LYNX Technik AG warrants that the product will be free from
defects in materials and workmanship for a period of two (2)
years from the date of shipment. If this product proves defective
during the warranty period, LYNX Technik AG at its option will
either repair the defective product without charge for parts and
labor, or will provide a replacement in exchange for the
defective product.
In order to obtain service under this warranty, customer must
notify LYNX Technik of the defect before expiration of the
warranty period and make suitable arrangements for the
performance of service. Customer shall be responsible for
packaging and shipping the defective product to the service
center designated by LYNX Technik, with shipping charges
prepaid. LYNX Technik shall pay for the return of the product to
the customer if the shipment is within the country which the LYNX
Technik service center is located. Customer shall be responsible
for payment of all shipping charges, duties, taxes and any other
charges for products returned to any other locations.
This warranty shall not apply to any defect, failure, or damage
caused by improper use or improper or inadequate
maintenance and care. LYNX Technik shall not be obligated to
furnish service under this warranty a) to repair damage resulting
from attempts by personnel other than LYNX Technik
representatives to install, repair or service the product; b) to
repair damage resulting from improper use or connection to
incompatible equipment; c) to repair any damage or
malfunction caused by the use of non LYNX Technik supplies; or
d) to service a product which has been modified or integrated
with other products when the effect of such modification or
integration increases the time or difficulty servicing the product.
THIS WARRANTY IS GIVEN BY LYNX TECHNIK WITH RESPECT TO THIS
PRODUCT IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR
IMPLIED. LYNX TECHNIK AND ITS VENDORS DISCLAIM ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE. LYNX TECHNIK`S RESPONISIBILITY TO REPAIR AND
REPLACE DEFECTIVE PRODUCTS IS THE SOLE AND EXCLUSIVE
REMEDY PROVIDED TO THE CUSTOMER FOR BREACH OF THIS
WARRANTY. LYNX TECHNIK AND ITS VENDORS WILL NOT BE LIABLE
FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTAL
DAMAGES IRRESPECTIVE OF WHETHER LYNX TECHNIK OR THE
VENDOR HAS ADVANCE NOTICE OF THE POSSIBILITY OF SUCH
DAMAGES.
Reference Manual C DA 3000 Version 2.0
Page 3
Reference Manual C DA 3000 Version 2.0
Regulatory information
Europe
Declaration of Conformity
WeLYNX Technik AG Brunnenweg 3
D-64331 Weiterstadt
Germany
Declare under our sole responsibility that the product
TYPE: C DA 3000
To which this declaration relates is in conformity with the following
standards (environments E1-E3):
EN 55103-1 /1996
EN 55103-2 /1996
EN 60950 /2001
Following the provisions of 89/336/EEC and 73/23/EEC directives.
USA
Winfried Deckelmann
Weiterstadt, August 2005
Place and date of issue Legal Signature
FCC 47 Part 15
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
Note: This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to the part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in
a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own
expense
Contact Information ..............................................................24
Page 5
Reference Manual C DA 3000 Version 2.0
This Page is intentionally left blank
Page 6
Reference Manual C DA 3000 Version 2.0
Getting Started
Packaging
The shipping carton and packaging materials
provide protection for the module during transit.
Please retain the shipping cartons in case
subsequent shipping of the product becomes
necessary.
Product Description
The C DA 3000 is a high quality 8 bit video digital to
analog converter designed primarily for broadcast
and professional applications.
The Module accepts 1 SDI input signal. Three
modes of operation are possible using the shared
connections on the front panel, GBR, YUV or SVideo component analog outputs. The module
also provides 3 composite outputs in parallel to the
selected component analog output. The module
provides two re-clocked SDI loop through signals for
further use downstream.
The C DA 3000 has a variety of features, which include:
• Component RGB or YUV or S video outputs
• 3 x Composite (CVBS) output
• PAL or NTSC operation
• Internal color bars
• Internal 2x over sampling (27MHz)
• 2 x reclocked SDI loop through outputs
• Local DIP-switches and LED's for control and
status monitoring.
• Microprocessor controlled.
• Remote control interface.
Page 7
Reference Manual C DA 3000 Version 2.0
The module has a built in micro-controller with local
controls, status and alarm indicators and well as
internal flash ram for storing setups. Any operational
parameters configured and stored into the module
are recalled when powered up. Remote control
and remote status monitoring is possible when used
with the rack frame option and host controller.
The C DA 3000 is part of the 3000 series of
MiniModules, which offer high quality, modularity
and flexibility in a very small form factor ideal for
applications where space is at a premium.
The modules can be used either stand alone using
the optional power supply brick, or as part of a
tightly integrated space saving system where up to
10 MiniModules can be mounted utilizing the
optional LYNX R FR 3005 / 3010 rack housing. This
includes integrated power supply and optional
remote control interfaces.
Page 8
Reference Manual C DA 3000 Version 2.0
Functional Diagram
Figure 1 below is the basic functional diagram for
the C DA 3000 MiniModule.
DRV
SDI LOOP 1
SDI LOOP 2
SDI IN
EQ
PLL
SER
PAR
Color
Bars
Remote
Micro Controller
Switch
Alarm
Figure 1- C DA 3000 Functional Diagram
Status
Module Layout
Figure 2 shows the physical layout of the C DA 3000
G or Y
B / U / Y (S)
R / V / C (S)
DAC
CVBS
CVBS
CVBS
MiniModule. Video I/O is made through standard
75 Ohm BNC video connections. Module
configuration is set via a small dip-switch located
behind an access hole in the bottom of the
module.
If the module is being used in a stand alone
application then the optional power supply (R PS
3001 E, R PS 3001 U, R PS 3001-3 or R PS 3004) is
required to power the module (not shown)
Page 9
Reference Manual C DA 3000 Version 2.0
Figure 2 – Module Layout
Page 10
Reference Manual C DA 3000 Version 2.0
Connections
Video Connections
The C DA 3000 MiniModule is configured with
standard 75 Ohm BNC connectors. Connection is
self-explanatory. We recommend the use of high
quality video cable suitable for digital video
connections to reduce the risk of interference or
errors due to excessive cable attenuation.
Note. Due to the compact design of the module it
will be necessary to use a connection tool to
secure the BNC video connectors to the module.
Page 11
Reference Manual C DA 3000 Version 2.0
Power Connections
If using the module in a stand-alone application
use the separate R PS 3001 E (for Europe), R PS 3001
U (USA) power brick option, the R PS 3001-3 desk
power supply or the R PS 3004 desk power supply
for 4 MiniModules.
DC Power Connector
The MiniModule has a captive power lead fitted to
the module, with a male 5 pin locking bayonet
connector. This connection provides DC power
and also data connectivity to the module.
Connector wiring is shown below.
i2C-SDA (data)
i2C-SCL (clock)
Power ConnectionData Connection
3
4
5
Male Connector
(view looking into connector from front)
Caution
Only use the optional LYNX R PS power
modules. Ensure the 5-pin power
2
1
GND
+ 5V
!
Page 12
connector is locked securely in place.
Installation
Mechanical
Stand Alone Operation
The C DA 3000 MiniModule can be used in a stand
alone application. There are two options for the use
of the module in this way.
a) Using the R FR 3005 Rack Frame 1 option. This
allows up to any 10 of the MiniModules to be
secured onto a rack frame assembly for 19 inch
rack mounting. This keeps the modules secured,
organized and out of the way. The R PS 3001
power brick option or the R FR 3010 option is
Reference Manual C DA 3000 Version 2.0
required to power each module. Please refer to
the R FR 3005 Reference Manual supplied with
this option for more details.
b) Single Use. The MiniModule can be powered
independently with one the R PS options and
used in any location where this functionality is
required.
!
Caution. Care needs to be taken
when using the module in this way, as
it is not physically secured. Keep the
module away from the floor to avoid
the risk of someone stepping or
tripping on the unit, and locate the
unit away from excessive sources of
heat and any sources or moisture.
If using more than one MiniModule in any
installation, the R FR 3005/3010 Rack frame
combination is highly recommended.
Page 13
Reference Manual C DA 3000 Version 2.0
Multiple Units
Most applications will require more than one
MiniModule, which can include any of the
available Series 3000 MiniModule product range.
There are two options for mounting multiple units.
a) Using the R FR 3005 Rack Frame option. This
allows up to any 10 of the MiniModules to be
secured onto a rack frame assembly for 19 inch
rack mounting. The R PS 3001 power brick
option or the R FR 3010 option is required to
power each module. Please refer to the R FR
3005 Reference Manual for more details.
b) Using the R FR 3010 Rack frame extension
option. Can be combined with the R FR 3005
Rack frame option. Each module plugs into a
connection bus, which provides common
power for all modules. (no R PS external power
supplies are needed). Remote control and
status monitoring of all modules is possible with
the addition of the R CT 5020 rack controller
and R CT 5030 master controller options. Please
refer to the respective reference manuals for
these options for details of mechanical
installation.
The very small size and density of the MiniModules
combined with the available rack frame options
allows the addition of a complex and custom signal
distribution system without taking any additional
front rack space. The rack frames are designed for
installation in the back of 19-inch racks where there
is normally plenty of available space. Ideal for
mobile truck installations and facility expansions
where space is at a premium.
Page 14
Reference Manual C DA 3000 Version 2.0
Electrical Installation.
Stand Alone Operation
The MiniModule requires the R PS 3001 power brick
option for stand-alone operation. Four versions are
available: R PS 3001 E for European markets, R PS
3001 U for the US markets, the R PS 3003-3 desk
power supply or the R PS 3004 desk power supply
for four MiniModules. Please ensure you have the
correct power option for your region. The
connection to the module is made with a small 5pin connector, which has a twist bayonet securing
system. Please make sure the connection is solid
and locked in place. A strain relief is included within
the module to prevent excessive strain on the
connection.
Signal connections should be made with care,
please ensure connections are correct and
compatible equipment is feeding / receiving the
signals from the module or damage can result.
Caution. Only use the optional LYNX R PS
power modules. Ensure the 5-pin power
connector is locked securely in place.
!
Caution. Care needs to be taken when
using the module in this way, if it is not
physically secured. Keep the module
away from the floor to avoid the risk of
!
someone stepping or tripping on the unit,
and locate the unit away from excessive
sources of heat and any sources or
moisture.
Page 15
Reference Manual C DA 3000 Version 2.0
Multiple Units
When installing multiple MiniModule units it is
recommended you use the R FR 3005 Rack Frame 1
and / or R FR 3010 Rack Frame 2 options. Please
refer to the documentation supplied with these
options for details on electrical installation.
Settings and Control
The C DA 3000 is configured via the integral 8position dip-switch. This is located on the bottom of
the module and can be accessed through the
cutout provided (fig 2)
Switch Settings
Below the switch settings for the 6-position dipswitch are defined. Please see the section following
the table for more detail on the switch function.
Switch Setting Function
1
2
3
4
5
6
7
8 Not used
ON Local control enabled (toogle for reaquire)
OFF Local control disabled
ON RGB component output
OFF YUV component output
ON Selection on switch 2 enabled
OFF S- Video output
ON Active line length 720 pixels
OFF Active line length 702 pixels
ON Test signal ON (Color Bars)
OFF Test signal OFF (Color Bars)
ON Test signal = NTSC format
OFF Test signal = PAL format
ON If no input, output = BLACK
OFF If no input, output = color bars
Page 16
Reference Manual C DA 3000 Version 2.0
Switch Function Detail
All settings are stored in Flash Ram inside the
module (see Auto Store section in this manual).
Settings will be recalled on power up. It is
recommended that switch 1 is set to OFF to disable
further local control when the module is configured
for use.
Dip Switch 1
This switch enables local control using the dipswitches. ON enables local control and makes
selections on the dip-switch active, and OFF
disables local control (locking out any changes).
If local control is disabled from remote (LED 3 OFF),
please toggle Dip Switch 1 to reaquire local control
Dip Switch 2
This switch selects either RGB or YUV component
analog outputs from the module. Only active when
switch 3 is set to ON. Note: Composite video
outputs are always present.
Dip Switch 3
This is used to select the Y/C (S-Video) output from
the module. OFF selects S-Video outputs. ON makes
the selection on switch 2 active
Dip Switch 4
Thisis used to set the active line length to either
digital blanking or analog blanking .
ON active line length 720 pixels (digital blanking),
OFF active line length 702 pixels (analog blanking)
Dip Switch 5
This will select the internal color bar test signal from
the module which is available on all outputs in the
video standard selected.
Page 17
Reference Manual C DA 3000 Version 2.0
Dip Switch 6
Selects the output mode for the test signal.
ON for NTSC, OFF for PAL
Dip Switch 7
Selects the output signal if no input signal is present.
ON selects signal BLACK,
OFF selects signal COLOR BARS
Factory Preset Condition
The C DA 3000 is delivered preset for the following
mode of operation:
• Local control ENABLED
• YUV Output
• Active line length 720 pixels
• Test signal OFF
• Test signal format PAL
• If no input output signal = COLOR BARS
If this is the mode of operation required, then no
adjustments are necessary.
Page 18
Reference Manual C DA 3000 Version 2.0
Alarm/LED Status Indicators
The C DA 3000 module has built in LED indicators,
which serve as alarm and status indication for the
module. Function is described below. The Indicators
are found on the bottom of the module and can
be seen through the access holes provided (Fig. 2)
Module Edge Status LED
LED COLOR
1
2
3 GREEN Local Control enabled
Alarm Indicator
GREEN Input Signal present
RED Input Signal lost
GREEN Input Standard PAL
YELLOW Input Standard NTSC
There is also a single alarm LED on the front side of
the module, which is designed for quick and easy
indication of a problem condition in installations
where visible access to the bottom of the module is
not convenient.
LED Color Indication
Green Input signal present (PLL lock / signal lock)
Yellow Test pattern selected (color bars)
Red No input video signal
LED OFF indicates power is lost, or there is a power
supply fault.
Page 19
Reference Manual C DA 3000 Version 2.0
Locate Function
For large systems which have many modules in
various locations we have added a utility which will
help visually identify a module quickly. (When used
in conjunction with the optional control system and
software)
Once the module has been identified on the
control system it is possible to initiate the “locate”
function and flash the module LEDs yellow in the
following continuous sequence.
3 short flashes…. Pause…. 3 short flashes …
This uses the alarm LED located on the front of the
module as well as any module edge LEDs that may
be used in the module.
Use of the locate function will not interfere with the
normal operation of the module.
For more details on this feature please check the
documentation supplied with the controller
software
Auto Store
If no parameters are changed for 10 seconds then
the current settings will be written into flash memory
automatically, this can be seen by the front LED
flashing yellow four times.
Page 20
Reference Manual C DA 3000 Version 2.0
Specifications
(C DA 3000)
Inputs
SDI Video Serial Digital Video. SMPTE 259M-C
Input Impedance 75 Ohms
Connection BNC
Cable length 250m Belden 8281 (270Mbit/s)
Return Loss > 15dB (270MHz)
Outputs (digital)
SDI Outputs 2 Reclocked Serial Digital Video. SMPTE 259M-C
Output Impedance 75 Ohms, BNC connection.
Return Loss > 15dB (270MHz)
Output Level 0.8v p-p (nominal)
Jitter < 0.2UI
Outputs (analog)
Analog Outputs 75 Ohm BNC connection
Output Level 0.7V p-p (nominal)
Return Loss > 35dB (5,75MHz)
Signal to Noise < -65dB (analog output stage with input black)
Operating Modes
Outputs RGB or YUV or S-video (selectable)
3 x Composite (CVBS)
TV Standard NTSC or PAL (selectable)
Test Internal Color Bars
Sync Sync on RGB (selectable)
Performance
Control Local settings (dip switch).
Status Monitoring Signal presence detection
Electrical Specifications
Operating Voltage + 5VDC
Power Consumption 3,5 VA
Connection DC input via 5 pin locking bayonet connector
Safety IEC 60950/ EN 60950/VDE 0805
Mechanical
Size 85.5mm x 35.3mm x 27mm + connectors
Weight 150 g
Ambient
Temperature 5°C to 35°C Maintaining specifications
-20°C to +70°C Storage
Humidity Max 80% non condensing
Supplied Accessories
Documentation C DA 3000 Reference Manual and quick ref guide
Page 21
Reference Manual C DA 3000 Version 2.0
Available Options
Below is a list of available options for the C DA 3000
MiniModule. Please refer to product brochures or
our web site for more detailed information.
Model Description
R PS 3001 E
R PS 3001 U
R PS 3001-3
R PS 3004
R FR 3004
R FR 3005
R FR 3010
R PS C15
R PS C25
R PS 5010
R CT 5020
R CT 5030
R CT 5010
R CT 3000
External brick power supply module for Series 3000
MiniModules. European market version. 100-240 VAC
input, +5V DC output.
External brick power supply module for Series 3000
MiniModules. USA market version. 110-240 VAC input,
+5V DC output.
External desk power supply module for Series 3000
MiniModules. 110-240 VAC input, +5V DC output.
External desk power supply module for 4 Series 3000
MiniModules. 110-240 VAC input, 4 x +5V DC output.
Mounting bracket for 4 MiniModules
Rack Frame 1. This is a basic 19 inch rack mountable
frame which can accommodate 10 MiniModules with
power bricks R PS 1 or can be extended with the R FR
3010.
Rack Frame 2. This is a card cage with integrated
central power supply, optional redundant power supply
and optional controller, which can accommodate 10
MiniModules. Can be combined with R FR 3005
1.5m cable extension to connect one MiniModule to R
FR 3010
2.5m cable extension to connect one MiniModule to R
FR 3010
Redundant power supply for the R FR 3010 card cage
Rack controller for the R FR 3010 rack frame
Master controllerwith TCP/IP Interface for the R FR 3010
rack frame
Rack Bus Extension for R FR 3010 rack frame. In
combination with R CT 5020
Service Adapter for remote configuration of one
MiniModule via PC or Palm
Page 22
Parts List
Due to the very dense design and high level of
integration there are no user serviceable electronic
assemblies within the C DA 3000 module.
C DA 3000 Mini Module (complete)
Description Video DA converter
Model Number C DA 3000
Part Number 6.155.001.280
Reference Manual C DA 3000 Version 2.0
Service
If you are experiencing problems, or have questions
concerning your C DA 3000 MiniModule please
contact your local distributor for assistance.
We offer a fixed cost service exchange program for
defective Series 3000 MiniModules out of Warranty.
Please contact your distributor or check our web
site for details on this program.
More detailed information and product updates
may be available on our web site:
www.lynx-technik.com
You will also find links to contact us directly for
assistance.
Page 23
Reference Manual C DA 3000 Version 2.0
Contact Information
Please contact your local distributor; this is your
local and fastest method for obtaining support and
sales information.
LYNX Technik can be contacted directly using the
information below.
AddressLYNX Technik AG
Brunnenweg 3
64331 Weiterstadt
Germany.
Website www.lynx-technik.com
E-Mail info@lynx-technik.com
LYNX Technik manufactures a complete range of
high quality modular products for broadcast and
Professional markets, please contact your local
representative or visit our web site for more product
information.
Page 24
Reference Manual C DA 3000 Version 2.0
Notes
Page 25
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.