Simply Connected
Quick Install Guide
XWR-600
Dual-Band Wireless 600N Router
Use the XWR-600 to:
Provide an Affordable Concurrent Dual-Band Wi-Fi
Network
Combine High Performance Gigabit and 802.11n Wireless
Functionality
Minimize Wireless Interference and Maximize Data Rates
Create a Secure Guest Network
XWR-600
Quick Install Guide
Quick Install Guide
Model Number: XWR-600
Dual-Band Wireless 600N Router
FCC ID: W59XWR600
IC: 8584A-XWR600
© 2014 Luxul. All Rights Reserved.
No part of this publication may be modified or adapted in any way, for any
purposes without permission in writing from Luxul. The material in this manual
is subject to change without notice. Luxul reserves the right to make changes to
any product to improve reliability, function, or design. No license is granted, either
expressly or by implication or otherwise under any Luxul intellectual property rights.
An implied license only exists for equipment, circuits and subsystems contained in
this or any Luxul product.
DOCUMENT CONVENTIONS
These graphical alerts are used in this document to indicate notable situations:
NOTE: Tips, hints, or special requirements that you should take note of.
CAUTION: Care is required. Disregarding a caution can result in data
loss or equipment malfunction.
WARNING!: Indicates a condition or procedure that could result in
personal injury or equipment damage.
FCC COMPLIANCE
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
CONTACT LUXUL
Sales
P: (801) 822-5450
E: sales@luxul.com
2
Technical Support
P: (801) 822-5450
E: support@luxul.com
14203 Minuteman Drive, Suite 201, Draper, UT 84020-1685 | luxul.com | 801-822-5450
LUX-QIG-XWR-600 0123140437
PACKAGE CONTENTS
The following items should be included in the box:
XWR-600 Dual-Band Wireless 600N Router
2 Dual Band RPSMA Male Antennas
Ethernet Cable
Power Adaptor
Quick Installation Guide
NOTE: If any of the listed items are missing or damaged, please contact
the reseller from whom you purchased for return/replacement.
HARDWARE DESCRIPTION
XWR-600 LED Indicators
Indicator Name Status Function
WPS
LED
5GHz ON Indicates a 5GHz wireless network is broadcasting.
2.4GHz ON Indicates a 2.4GHz network is broadcasting.
ON Indicates the XWR-600 is ready for WPS pairing.
Simply Connected
1-4 LED ON Indicates a device is connected to the Ethernet port
number.
FLASHING indicates data packets are being transmitted to the
connected device.
Internet
LED
USB
LED
Power
LED
© 2014 Luxul. All Rights Reserved.
Other trademarks and registered trademarks are the property of their respective owners
ON Indicates the XWR-600 is connected to the ISP.
FLASHING Indicates data packets are being transmitted
ON Indicates a USB enabled device is connected and
configured.
ON ON indicates power is applied to the XWR-600.
OFF Indicates power is not applied to the XWR-600.
3
XWR-600
Quick Install Guide
Rear Panel
XWR-600 Rear Panel View
Antenna Ports: 2 RPSMA female antenna ports to connect the included
antennas
Power Input: Power adapter included
NOTE: To hard reboot the router, remove the power adapter. Wait 10
WAN Port: 1 Black RJ-45 Ethernet Port for Internet connection
LAN 1 - 4 Ports: 4 Green RJ-45 Ethernet Ports for connecting to the local network
WPS/Reset Button: Used to confi gure WPS or restore factory default settings
seconds and re-apply power.
NOTE: It is recommended that a Luxul switch be used in conjunction
with the XWR-600 to increase number of local ports available.
CAUTION: Holding the WPS button longer than 10 seconds will result
in a factory reset
Side Panel
XWR-600 Side Panel View
USB Port: 1 USB 2.0 ports for connecting USB based printers and hard drives
4
14203 Minuteman Drive, Suite 201, Draper, UT 84020-1685 | luxul.com | 801-822-5450
LUX-QIG-XWR-600 0123140437
Simply Connected
PREPARING FOR INSTALLATION
System Requirements
Computer supporting TCP/IP and equipped with a Web browser. Supported Web
browser versions include I.E. 9.0, Firefox 3.6, Safari 5.0, Chrome 6.0, Opera 10.6
and up. The Web browser is used to confi gure the XWR-600.
Power must be AC 100-240V~ 1.0A 50/60Hz.
XWR-600 INSTALLATION
Desktop Installation
For use as a desktop device, position the XWR-600 on a desk or other horizontal
surface with adequate room around the XWR-600 for ventilation.
Wall Installation
The XWR-600 Is keyholed to allow installation on a wall or ceiling. Use the
Mounting Pattern (Page 8-9) for keyhole alignment.
Hardware Setup
Attach Antennas: Connect the included Dual Band Antennas to both
antenna ports.
NOTE: Both antennas should be installed prior to powering up the
WAN Connection: Connect the Ethernet cable from the modem/router equipment provided by your Internet Service Provider (ISP) to the black WAN port of
the XWR-600.
AC Power: Connect the included AC Adapter to the XWR-600 fi rst and then to
the AC outlet.
XWR-600 and are required for optimal performance.
© 2014 Luxul. All Rights Reserved.
Other trademarks and registered trademarks are the property of their respective owners
5
XWR-600
Quick Install Guide
CONFIGURATION
Default IP Address
The XWR-600 default IP address is 192.168.0.1. This address can be changed.
However, for hassle free installation of other XenConnect™ plug and play Luxul
devices, it is recommended that the default IP value be maintained.
Parameter: Default Value
Default IP address: 192.168.0.1
Default user name: admin
Default password: admin
Connect a Client Device
Use a computer or mobile device to connect via Ethernet or wireless to the XWR-600.
The DHCP server on the XWR-600 is configured by default. If your client device is set
to obtain an address automatically, no further configuration is required.
Connecting a Wireless Client Device: Connect the client device to one of the
XWR-600 default wireless networks (LuxulXen600_24 or LuxulXen600_5X).
Both Wireless networks will run in Open Security mode. A passphrase is not
required until Wireless Security is configured.
Connecting an Ethernet Device: Use Ethernet cable to connect your computer
or device to one of the XWR-600 LAN ports.
Login
Login to the router with the following steps:
1. Open a Web browser, and enter 192.168.0.1. The router login screen will appear.
2. Enter the user name and password (default user name and default password
are both set as “admin”), and then click “OK” to login to the router configuration
interface.
NOTE: Only devices that support 5GHz will see LuxulXen600_5X
6
wireless network.
14203 Minuteman Drive, Suite 201, Draper, UT 84020-1685 | luxul.com | 801-822-5450
LUX-QIG-XWR-600 0123140437
Simply Connected
WPS CONFIGURATION/RESET BUTTON
Used to configure WPS (Wi-Fi Protected Setup) or restore factory default settings
w
To configure WPS, press and hold the WPS/Reset button until the WPS LED
turns on (typically about 5 seconds). The XWR-600 is now in WPS pairing
mode. Follow the pairing instructions for your client device and enter the
XWR-600 WPS pin number (12345678) when prompted.
CAUTION: Holding the WPS button longer than 10 seconds will result
CAUTION: For optimal security, it is recommended to disable WPS
w
To reset to factory defaults, press and hold the WPS/Reset button until the
System LED stops flashing (approximatly 20 seconds). A factory reset will take
one minute or more to complete. A successful factory reset is indicated when
all of the Port LEDs flash once. When the System LED starts flashing again the
unit is ready.
CAUTION: Resetting the XWR-600 to factory defaults will remove all
NOTE: To hard reboot the router, remove the power adapter. Wait 10
in a factory reset
after your client devices have been configured.
custom settings.
seconds and re-apply power.
ADVANCED SETTINGS
For login and advanced settings information go to luxul.com
© 2014 Luxul. All Rights Reserved.
Other trademarks and registered trademarks are the property of their respective owners
7
XWR-600
Quick Install Guide
ADVANCED SETTINGS
For advanced settings information go to luxul.com
WARNINGS AND SAFETY INFORMATION
Verify that the electrical circuits have appropriate grounding and overload protection.
Attach only approved power cords to the device.
Verify there is adequate ventilation around the device, and that ambient temperatures meet
equipment operation specifications.
The XWR-600 is designed for indoor use only. DO NOT place this outdoors.
DO NOT install in or near hot or humid places, such as a kitchen or bathroom. Take care to
minimize exposure to excessive heat or moisture.
Small parts and plastic bags used for packaging may be harmful to small children. KEEP All
ACCESSORIES OUT OF THE REACH OF CHILDREN!
The XWR-600 may become hot when in use for extended time periods. This is normal and is not a
malfunction. DO NOT install where it will be exposed to paper, cloth or other flammable materials.
REGULATORY COMPLIANCE
The device complies with internationally recognized standards covering human exposure to electromagnetic fields from radio devices. This equipment also complies with FCC radiation exposure
set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC
radio frequency exposure limits, human proximity to the antenna shall not be less than 20 cm (8
inches) during normal operation.
Unauthorized antennas, modifications, or attachments could cause damage and may violate regulatory approvals. Any changes or modifications not expressly approved by the party responsible for
compliance could void the authority to operate the equipment.
The equipment version marketed in the U.S. is restricted to usage of channels 1-11 only.
Health and Safety Recommendations
Warnings for the use of Wireless Devices: Please observe all warning notices with regard to the
usage of wireless devices
Potentially Hazardous Atmospheres: You are reminded of the need to observe restrictions on the
use of radio devices in fuel depots, chemical plants etc. and areas where the air contains chemicals
or particles (such as grain, dust, or metal powders).
Safety in Hospitals: Wireless devices transmit radio frequency energy and may affect medical
electrical equipment. When installed adjacent to other equipment, it is advised to verify that the
adjacent equipment is not adversely affected.
RF Exposure Guidelines
Safety Information: The device complies with internationally recognized standards covering
human exposure to electromagnetic fields from radio devices.
8
14203 Minuteman Drive, Suite 201, Draper, UT 84020-1685 | luxul.com | 801-822-5450
LUX-QIG-XWR-600 0123140437
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the
radiator & your body.
NOTE: (1)The manufacturer is not responsible for any radio or TV interference
caused by unauthorized modifications to this equipment.(2) To avoid
unnecessary radiation interference, it is recommended to use a shielded
RJ45 cable
Industry Canada (RSS-Gen Issue 2)
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject
to the following two conditions: (1) this device may not cause interference, and (2)this device must
accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareilsradio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1)l’appareil ne doit pas
produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and
compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and
compliance.
Le dispositif rencontre l’exemption des limites courantes d’évaluation dans la section 2.5 de RSS 102
et la conformité à l’exposition de RSS-102 rf, utilisateurs peut obtenir l’information canadienne sur
l’exposition et la conformité de rf.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter. This equipment should be installed and operated with a minimum distance of 20
centimeters between the radiator and your body.
Cet émetteur ne doit pas être Co-placé ou ne fonctionnant en même temps qu’aucune autre
antenne ou émetteur. Cet équipement devrait être installé et actionné avec une distance minimum
de 20 centimètres entre le radiateur et votre corps.
CAN ICES-03(B)/NMB-3(B)
Information on this document supersedes all previous versions. Products and documents
subject to change without notice. Products may be discontinued without notice.
LUX-QIG-XWR-600
0123140437
14203 Minuteman Drive, Suite 201, Draper, UT 84020-1685
luxul.com | 801-822-5450
Loading...