Simply Connected
Quick Install Guide
ABR-4400
AV Series
Multi-WAN Gigabit Router
Use the ABR-4400 to:
Add High Performance IP Network Routing
Functionality to your AV Rack Solutions
Create a Secure Guest Network with VLANs
Enable Secure Remote Access to the
Network via VPN
Optimize VoIP, Streaming Media and
Other Demanding Applications
Improve Network Reliability and Performance
with Multi-WAN Capability
Protect Your Network with Firewall
and Security Features
ABR-4400
Quick Install Guide
Quick Install Guide
Model Number: ABR-4400
AV Series Multi-WAN Gigabit Router
© 2014 Luxul. All Rights Reserved.
No part of this publication may be modified or adapted in any way, for any
purposes without permission in writing from Luxul. The material in this manual is
subject to change without notice. Luxul reserves the right to make changes to any
product to improve reliability, function, or design. No license is granted, either expressly or by implication or otherwise under any Luxul intellectual property rights.
An implied license only exists for equipment, circuits and subsystems contained in
this or any Luxul product.
DOCUMENT CONVENTIONS
These graphical alerts are used in this document to indicate notable situations:
NOTE: Tips, hints, or special requirements that you should take note of.
CAUTION: Care is required. Disregarding a caution can result in data
loss or equipment malfunction.
WARNING!: Indicates a condition or procedure that could result in
personal injury or equipment damage.
FCC COMPLIANCE
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
CAN ICES-3 (B)/NMB-3(B)
CONTACT LUXUL
Sales
P: 801-822-5450
E: sales@luxul.com
2
a: 14203 Minuteman Drive, Suite 201, Draper, UT 84020-1685 | luxul.com | 801-822-5450
Technical Support
P: 801-822-5450
E: support@luxul.com
LUX-QIG-ABR-4400 117141122
Simply Connected
PACKAGE CONTENTS
The following items should be included in the box:
ABR-4400 AV Series Multi-WAN Gigabit Router
Power Cord
Two L-shaped rack mounting brackets and screws and four rubber pads
Quick Installation Guide
NOTE: If any of the listed items are missing or damaged, please contact
the reseller from whom you purchased for return/replacement.
HARDWARE DESCRIPTION
Front Panel
ABR-4400 Front Panel View
Back Panel
ABR-4400 Rear Panel View
Factory Reset Button: Used to restore factory default settings.
To reset to factory defaults, press and hold the Reset button for 15 seconds
then release. A factory reset may take approximately a minute to complete. A
successful factory reset is indicated by all of the Port LEDs fl ashing once. When
the System LED begins to fl ash the unit is ready.
NOTE: To hard reset the router use the power switch. Turn the router
off, wait 10 seconds and turn the unit back on.
CAUTION: Resetting the ABR-4400 to factory defaults will remove all
© 2014 Luxul. All Rights Reserved.
Other trademarks and registered trademarks are the property of their respective owners
custom settings.
3
ABR-4400
Quick Install Guide
LED Indicators
Indicator Description Function
POWER Power LED ON indicates the ABR-4400 has power.
SYSTEM System
Status LED
USB USB Connection
Status
WAN/LAN
Front
WAN/LAN
Rear
WAN Ports: (1 dedicated, 3 shared) RJ-45 Ethernet Ports for connecting up to
WAN and LAN
Status LED
WAN and LAN
Status LED
4 independent internet connections
LAN Ports: (1 dedicated, 3 shared) RJ-45 Ethernet Ports for connecting to the
local network
USB Ports: 1 USB 2.0 ports for connecting USB based printers and hard drives.
FLASHING indicates the ABR-4400 is functioning
correctly.
ON indicates the ABR-4400 is booting.
OFF indicates the system is not functioning correctly.
ON indicates a USB device is connected and configured
BLUE/GREEN TOP ROW ON
indicates there is a 10/100 Mbps device connected
BLUE/GREEN BOTTOM ROW ON
indicates there is a 1000 Mbps device connected
FLASHING BLUE/GREEN
indicates data packets are being transferred.
YELLOW ON
indicates there is a 10/100 Mbps device connected
GREEN ON
indicates there is a 1000 Mbps device connected
FLASHING YELLOW or GREEN
indicates data packets are being transferred.
NOTE: It is recommended that a Luxul switch be used in conjunction
with the ABR-4400 to increase number of local ports available.
PREPARING FOR INSTALLATION
System Requirements
Ethernet Cables to connect the ABR-4400 to Ethernet enabled devices
USB Cables to connect the ABR-4400 to USB 2.0 enabled devices
4
a: 14203 Minuteman Drive, Suite 201, Draper, UT 84020-1685 | luxul.com | 801-822-5450
LUX-QIG-ABR-4400 117141122
Simply Connected
Computer supporting TCP/IP and equipped with a Web browser. Supported
Web browser versions include I.E. 10.0, Firefox 3.6, Safari 5.0, Chrome 10.0, Opera
10.6 and up. The Web browser is used to confi gure the ABR-4400.
Power must be AC 100-240V~ 0.1A 50/60Hz.
Before Connecting to the Network
The ABR-4400 can be rack-mounted or used as a desktop router. Before connecting
to the network, please be aware of the following requirements:
Install the ABR-4400 in a stable/safe place to avoid any possible damage
Make sure there is adequate space around the ABR-4400 for adequate ventilation and proper heat dissipation. It is recommended to have at least 4-6 inches
around all sides.
Do not place heavy articles on the ABR-4400.
Power outlets should be within 5 feet of the ABR-4400.
Verify the ground connection of the outlet is functioning properly.
Check the power cord to confi rm a secure connection.
Avoid placement in direct sunlight.
When installing the ABR-4400 on a fl at surface, attach the rubber feet to the
bottom of the device to avoid scratching the surface.
ABR-4400 INSTALLATION
Installing the ABR-4400 in a Rack
The ABR-4400 can easily be installed in a standard 19” rack. The ABR-4400 includes two
mounting ears for installing and stabilizing the router. For attaching the mounting ears
and installing the switch within a rack, please refer to the following illustration:
Rack-Mounting the ABR-4400
Using the included screws, attach the mounting ears to each side of
the switch,.
Mount the router in the rack with the LEDs facing outwards. Be sure the
router is level and properly secured within the rack.
© 2014 Luxul. All Rights Reserved.
Other trademarks and registered trademarks are the property of their respective owners
5
ABR-4400
Quick Install Guide
Desktop Setup
For use as a desktop device, position and apply the included rubber feet to the
bottom of the ABR-4400.
Attaching the Rubber Feet to the ABR-4400
CONNECTING DEVICES
Before installing the ABR-4400, test the Internet connection to validate that it is
functioning properly. When Internet access has been confirmed, follow the steps
below for Router installation.
1. Establish LAN Connection: Connect one of the four ABR-4400 LAN ports
to a switch, access point, or computer
2. Establish WAN Connection: Connect the Internet cable to WAN 1 of the
ABR-4400 WAN ports
3. Connect AC Power: Connect the included AC power cable to the ABR-4400
first and then to the AC outlet.
NOTE: By default WAN 1 and LAN 1-4 are configured. The ABR-4400
must be configured to provide additional WAN ports if needed.
Default IP Address
The ABR-4400 default IP address is 192.168.0.1. This address can be changed.
However, for hassle free installation of other plug and play Luxul devices, it is
recommended that the default IP value be maintained.
Connecting a Client Device
Connect the client device to one of the ABR-4400 LAN ports or to a switch that is
connected to a ABR-4400 LAN port. The DHCP server on the ABR-4400 is configured by default. If your client device is set to obtain an address automatically, no
further configuration is required.
Verifying Connectivity
After automatic configuration of the TCP/IP parameters, the ping command can be
used to check connectivity between the ABR-4400 and the client device.
6
a: 14203 Minuteman Drive, Suite 201, Draper, UT 84020-1685 | luxul.com | 801-822-5450
LUX-QIG-ABR-4400 117141122
Simply Connected
Windows Devices:
1. Select Start >> Run input cmd in the Run line then press enter.
2. At the newly opened command interface enter the following command: ping
192.168.0.1 and press enter. If connected properly, the system should report back a
result as follows: packets sent=4, packets received=4, packets lost=0. This means
the device is connected with a valid IP address.
Login
Parameter: Default Value
Default IP address: 192.168.0.1
Default user name: admin
Default password: admin
Login to the router with the following steps:
1. Plug an Ethernet cable into any of the four LAN ports of the router
2. Plug the other end into the Ethernet port of your computer
3. Power on the router
4. Check to see that the IP address of the computer is within this network segment:
192.168.0.xxx (“xxx” ranges 2~254). For example, 192.168.0.100.
5. Open the Web browser, and enter 192.168.0.1. The router login window appears,
as shown below.
6. Enter the user name and password (default user name and default password
are both set as “admin”), and then click “OK” to login to the router configuration
window.
ADVANCED SETTINGS
For advanced settings information go to luxul.com
WARNINGS AND SAFETY INFORMATION
Read all installation instructions and site survey reports, and verify correct equipment
installation before connecting the ABR-4400 to its power source.
Verify that the electrical circuits have appropriate grounding and overload protection.
Attach only approved power cords to the device.
DO NOT pull any connected cable with force. When disconnecting cables, do so by disconnecting first from the ABR-4400. When reconnecting, connect the ABR-4400 first and then
the Power/data source.
© 2014 Luxul. All Rights Reserved.
Other trademarks and registered trademarks are the property of their respective owners
7
Verify there is adequate ventilation around the device, and that ambient temperatures meet
equipment operation specifications.
The ABR-4400 is designed for indoor use only. DO NOT place this outdoors.
DO NOT install in or near hot or humid places, such as a kitchen or bathroom. Take care to
minimize exposure to excessive heat or moisture.
Small parts and plastic bags used for packaging may be harmful to small children. KEEP All
ACCESSORIES OUT OF THE REACH OF CHILDREN!
The ABR-4400 may become hot when in use for extended time periods. This is normal
and is not a malfunction. DO NOT install where it will be exposed to paper, cloth or other
flammable materials.
The ABR-4400 contains no user-serviceable parts. If it is not working properly, contact your
dealer and ask for help. DO NOT attempt to disassemble the device.
REGULATORY COMPLIANCE
FCC Statement:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment uses and can radiate radio frequency energy, and
if not installed and used in accordance with the instructions may cause harmful interference to radio
communications. However; there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
Hereby, Luxul, 14203 Minuteman Drive, Suite 201, Draper, Utah, 84020, declares that this
Luxul ABR-4400 is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
For a copy of this report send a self addressed stamped envelope to:
Luxul CE, 14203 Minuteman Drive, Suite 201, Draper, Utah, 84020.
Information on this document supersedes all previous versions. Products and documents
subject to change without notice. Products may be discontinued without notice.
LUX-QIG-ABR-4400
117141122v1
a: 14203 Minuteman Drive, Suite 201, Draper, UT 84020-1685
luxul.com | 801-822-5450
Loading...