Lux Products PSPH521 User Manual

INSTALLATION AND OPERATING INSTRUCTIONS

OFF

EGYROW2BC

TERMINALS

SCREW ANCHORS

BASE

PSPH521 SERIES

PROGRAMMABLE

O M

Y A D

T A E

H M P

DOWN

Installs Easily

Complete, Easy To Read Programming And Installation Instructions Inside

LUX PRODUCTS CORPORATION • Mt. Laurel, New Jersey 08054, USA 43343-04

WARNING: Use Energizer®or DURACELL®Alkaline Batteries Only.

Energizer®is a registered trademark of Eveready Battery Company, Inc.

DURACELL®is a registered trademark of The Gillette Company, Inc.

IMPORTANT!

Thank you for your confidence in our product. To obtain the best results from

READ

INSTALLATION

INSTRUCTIONS

FIRST

FEATURES

•

The Unit can be used with most two stage heat and one stage cool heat pump systems. It cannot be

used with 120 volt heating systems. Ask your dealer for other LUX thermostats to control those systems.

• The Unit is programmable.

There are four programming periods per day. Each period can be programmed separately.

• You can use the built-in time/temperature programs, or alter them to suit your schedule. The Unit

provides separate programs for weekdays and weekends

- for both heating and cooling. You can override the programmed temperatures for as little as one programming period or for an entire vacation.

• In cool weather, when the system switch is set to HEAT, the Unit will maintain cooler “set back” room temperatures to save energy. It will then change to warmer “comfort” settings — all automatically, at specified times during the day.

• In warm weather, when the system switch is set to COOL, the Unit will maintain warmer “set back” room temperatures to save energy. It will then change to cooler “comfort” settings - all automatically, at specified times during the day.

• A large liquid crystal display shows time, day of the week, and room and set temperatures. It will remind you when the filter should be changed in your blower and track your system’s energy usage.

• Temperature swing adjustment lets you fine-tune your system for maximum comfort and economy.

• A 4-minute minimum on/off time in COOL prevents your air conditioning system from being damaged.

• The thermostat can be powered either by a common wire from the 24Vac transformer with two Energizer®or DURACELL®"AA" size alkaline batteries as backup or exclusively by two Energizer®or DURACELL®"AA" size alkaline batteries.

CAUTION

• Your thermostat is a precision instrument. Please handle it with care.

• Turn off electricity to the appliance before installing or servicing thermostat or any part of the system. Do not turn electricity back on until work is completed.

• Do not short (jumper) across electric terminals at control on furnace or air conditioner to test the system. This will damage the thermostat and void your warranty.

• All wiring must conform to local codes and ordinances.

• This thermostat is designed for use with 24 volt and millivolt systems. The thermostat should be limited to a maximum of 1.0 amps; higher amperage may cause damage to the thermostat. If you are in doubt, call your utility company.

your investment, please read these instructions and acquaint yourself with your purchase before installing your new thermostat. Then follow the installation procedures, one step at a time. This will save you time and minimize the chance of damaging the thermostat and the systems it controls.

These instructions may contain information beyond that required for your particular installation. Please save for future reference.

LUX Speed Dial

HEAT PUMP THERMOSTAT

HEAT

OFF

COOL

1500

Patents Pending

original set temperature appears or wait for

TO SET TIME & DAY

•Rotate Dial to SET WEEKDAY or WEEKEND PROGRAM

•Press UP to change current day.

•Press NEXT.

•Press UP/DOWN to set time.

Rotate the dial to the RUN position to close the door.

Y A D

T A E H

M P

DOWN

SET

SUNDAY

SATURDAY

RESET

FAN

PROGRAM

HEAT

AUTO

SET

OFF

FILTER

WEEKDAY

HOLD

COOL

PROGRAM

SET

RUN

DAY/TIME

Patents Pending

SIMPLIFIED INSTRUCTIONS

•Press UP/DOWN to set time.

TEMPORARY TEMPERATURE OVERRIDE

TO SET TIME & DAY

•Press UP/DOWN to adjust set temperature.

•Rotate Dial to SET

TO SET PROGRAMS

•To clear OVERRIDE press UP/DOWN until

DAY/TIME.

•Rotate Dial to SET

original set temperature appears or wait for

•Press UP to change

Choose Heat or CoolSet Day & Time

Liquid Crystal Display

DOWN

RESET

SET

WEEKEND PROGRAM

HOLD

RUN

SIMPLIFIED INSTRUCTIONS

TO SET PROGRAMS

•Rotate Dial to SET WEEKDAY, SATURDAY or SUNDAY PROGRAM.

•Press UP/DOWN to adjust start time.

•Press NEXT.

•Press UP/DOWN to adjust

temperature.

•Press NEXT.

•Repeat as needed or rotate

dial to RUN to stop Programming.

Easy as

1500

TEMPORARY TEMPERATURE OVERRIDE

•Press UP/DOWN to adjust set temperature.

•To clear OVERRIDE press UP/DOWN until

original set temperature appears or wait for the start tf the next period.

TEMPERATURE HOLD

•Press HOLD. Adjust temperature as desired with UP/DOWN.

•To clear, press HOLD again.

1–2–3

FAN

EMER

AUTO

HEAT OFF

COOL

O M

Y A D

T A E H

M P

DOWN

SET

SUNDAY

SATURDAY

RESET

FAN

PROGRAM

AUTO

SET

FILTER

WEEKDAY

HOLD

PROGRAM

SET

RUN

DAY/TIME

SIMPLIFIED INSTRUCTIONS

•Press UP/DOWN to set time.

TEMPORARY TEMPERATURE OVERRIDE

TO SET TIME & DAY

•Press UP/DOWN to adjust set temperature.

•Rotate Dial to SET

•To clear OVERRIDE press UP/DOWN until

TO SET PROGRAMS

DAY/TIME.

•Rotate Dial to SET

•Press UP to change

The Active Program Period

MORN

DAY

EVE

NIGHT

SET

WEEKDAY PROGRAM

SET

DAYTIME

The Set Temperature

Thermostat Body

System Switch

Fan Switch

Easy to follow instructions

Thermostat Cover

INSTALLATION

Please read all instructions carefully before beginning installation.

TOOLS REQUIRED

#1 Phillips screwdriver (small) Drill with 3/16-in. (4.8mm) bit

THERMOSTAT LOCATION

On replacement installations, mount the new thermostat in place of the old one unless the conditions listed below suggest otherwise. On new installations, follow the guidelines listed below.

1. Locate the thermostat on an inside wall, about 5 ft. (1.5m) above the floor, and in a room that is used often.

2. Do not install it where there are unusual heating conditions, such as: in direct sunlight; near a lamp, radio, television, radiator, register, or fireplace; near hot water pipes in a wall; near a stove on the other side of a wall.

3. Do not locate in unusual cooling conditions, such as: on a wall separating an unheated room; or in a draft from a stairwell, door, or window.

4. Do not locate in a damp area. This can lead to corrosion that will shorten thermostat life.

5. Do not locate where air circulation is poor, such as: in a corner or an alcove; or behind an open door.

CAUTION

To avoid electrical shock and to prevent damage to the furnace, air conditioner, and thermostat, disconnect the power supply before beginning work. This can be done at the fuse box, at the circuit breaker, or at the appliance.

6. Do not install the unit until all construction work and painting has been completed.

7. This thermostat does not require leveling.

REMOVING THE OLD THERMOSTAT

Switch electricity to the furnace and air conditioner OFF; then proceed with the following steps.

1. Remove cover from old thermostat. Most are snap-on types and simply pull off. Some have locking screws on the side. These must be loosened.

2. Note the letters printed near the terminals. Attach labels (enclosed) to each wire for identification. Remove and label wires one at a time. Make sure the wires do not fall back inside the wall.

3. Loosen all screws on the old thermostat and remove it from the wall.

CAUTION

Read instructions carefully before removing any wiring from existing thermostat. Wires must be labeled before they are removed. When removing wires from their terminals, ignore the color of the wires since these may not comply with the standard.

MOUNTING THE UNIT ON THE WALL

1. Strip insulation 3/8 in. (9.5mm) from wire ends and clean off any corrosion.

2. Fill wall opening with non-combustible insulation to prevent drafts from affecting the thermostat.

3. Press up on the button on bottom of thermostat and swing the body away from the base and up to remove the body from the base.

CAUTION

Be careful not to drop the body or disturb electronic parts.

Leave the cover closed while the body is being removed from the base.

NOTE

If you are mounting the base to a soft material like plasterboard or if you are using the old mounting holes, the screws may not hold. Drill a 3/16-in. (4.8mm) hole at each screw location, and insert the plastic anchors provided. Then mount the base as described below.

Attaching Wires

4. Hold the base against the wall, with the wires coming through wherever it is convenient for wiring. Route the wires to below the terminal block. Position the base for best appearance (to hide any marks from an old thermostat). Attach the base to the wall with the two screws provided.

CAUTION

SET

WEEKDAY PROGRAM

HOLD

RESET

SET

DAYTIME

SET

WEEKEND PROGRAM

RUN

EMER HEAT OFF COOL

FAN

AUTO

SIMPLIFIED INSTRUCTIONS

TO SET PROGRAMS

TEMPORARY TEMPERATURE OVERRIDE

TO SET TIME & DAY

GE YRO W2 B C

COMPRESSOR

RELAY

FAN

RELAY

EMERGENCY

HEAT RELAY

HEAT

CHANGEOVER

VALV E

COOL

CHANGEOVER

VALV E

AUX HEAT

RELAY

COMMON

L1 (HOT)

L2 (COMMON)

POWER SUPPLY PROVIDE DISCONNECT MEANS AND OVERLOAD PROTECTION AS REQUIRED.

OLD TERMINAL DESIGNATIONS

TYPICAL

CONNECTION

NEW THERMOSTAT

TERMINAL

DESIGNATIONS

C, X, X1, X2, Z

E, K

G, F

L, A, A1

R, V

W2, H2, R4, W3, Y

Y, C1, M, Y1

TAPE OFF

Heating Changeover Valve

Common

Emergency Heat Relay

Fan Relay

Check Heat Pump Indicator

Cooling Changeover Valve

24V System or Heating

Transformer

Stage 2 Heating Relay or

Auxiliary Heat Relay

Stage 1 Compressor

Contractor

FAN ON

FAN AUTO

EMER

HEAT

OFF

COOL

The fan runs continuously for increased air circulation.

Normal Setting. Fan is energized with the system.

Auxiliary heat is used for heating. The compressor is deenergized.

The thermostat controls your heating.

Both heating and cooling are off.

The thermostat controls your cooling.

DAY

MONDAY

THROUGH

FRIDAY

PERIOD HEAT

TEMP.

MORN

DAY

EVE

NIGHT

SATURDAY

AND

SUNDAY

MORN

DAY

EVE

NIGHT

TEMP.TIME TIME

COOL

Do not allow wires to touch each other or parts on thermostat. Wires must be trapped between black spacer and brass terminal. Also, be sure to tighten securely all terminal screws.

TERMINAL DESIGNATIONS

NOTE

When replacing batteries, you have

approximately 1 minute before programs are lost.

1. Remove fresh batteries from their carton.

2. Remove body of thermostat as described at bottom of first column.

3. Remove the battery clip and batteries.

4. Install two Energizer®or DURACELL®"AA" size alkaline batteries in the battery clip. Observe the polarity marking shown in the clip.

WARNING: Use Energizer®or DURACELL

Alkaline Batteries Only.

5. Place body back on the wall. Hook the bottom of the body onto the base, swing the body up, and snap the body onto the base.

Installation is now complete. Be sure to turn the power back on to your heating and /or air conditioning system. If this is the first time you are installing batteries, the thermostat will display “SUN 12:00 AM”. Within 90 seconds the thermostat will begin to display the room temperature alternately with the time. To correct the display, see “Setting the TIME and DAY,” after you set the programs.

REPLACE BATTERIES WHEN

INDICATOR APPEARS

CAUTION

The Unit is protected against normal static electric discharges. However, in extremely dry weather you should touch another metal object before the Unit to avoid potential loss of programs.

NOTE: A typical hookup will require either a "B" or "O" wire, but not both. If you have both a "B" and "O" wire, please call technical service.

TYPICAL HOOKUP

SETTING THE FAN AND SYSTEM SWITCHES

OPERATION

The Unit alternately displays the current time and the room temperature. It also displays the day of the week and the currently active program period that is controlling the temperature: MORN, DAY, EVE, or NIGHT.

The set point temperature will appear in the right side of the display. In the winter, set the system switch to HEAT to control your heating system. In the summer, set the switch to COOL to control your air conditioner. In spring and fall or when windows are open, you can set the system switch OFF.

Setting the FAN switch to AUTO automatically runs your system’s fan during heating and cooling. Setting the FAN switch to ON runs your system’s fan continuously even without heating or cooling.

THE BUILT IN PROGRAMS

Push in the RESET key. This sets the built-in heating and cooling programs. To review the built-in programs,press NEXT or PREVIOUS repeatedly; when you are done, press RETURN.

You can use the built-in programs as shown, or change them as you wish. Each day is divided into four periods. Each period has its own starting time and temperature.

This thermostat is “armchair programmable” You can make any program or setting changes with the thermostat body off or on the wall thermostat base.

PERIOD HEAT COOL

WEEKDAYS

preprograms DAY 8:00 AM 62° 8:00 AM 85°

SAT & SUN DAY 8:00 AM 62° 8:00 AM 85°

preprograms EVE 6:00 PM 70° 6:00 PM 78°

MORN 6:00 AM 70° 6:00 AM 78°

EVE 6:00 PM 70° 6:00 PM 78°

NIGHT 10:00 PM 62° 10:00 PM 82°

MORN 6:00 AM 70° 6:00 AM 78°

NIGHT 10:00 PM 62° 10:00 PM 82°

PROGRAMMING CHART

INSTALLING BATTERIES

The Unit requires batteries to retain its programming in memory. Replace the batteries when the REPLACE indicator appears in the display or at least once a year.

+ 1 hidden pages