Luxor|H.Wilson LT45PC User Manual
Instruction Sheet - Endura Presentation Table
Model LT45PC
Customer Service Department
Luxor
2245 Delany Road
Waukegan, IL 60087
Ph: 847/244-1800 • 800/323-4656
Fax: 847/244-1818 • 800/327-1698
18” LEG
RUBBER BAND
SIDE
PANEL
LEGS
PARTS LIST
Model LT45PC
1 - Top shelf w/handle 1 - Door in frame
1 - Center shelf w/eight leg posts 1 - Grommet cap
1 - bottom shelf w/caster sockets 1 - Cord guide cover
4 - Short legs 1 - Grommet ring
4 - Long legs 1 - Rubber band
2 - Cabinet side panels 1 - Cord wrap
1 - Back panel 1 - Keyboard assembly
4 - Casters 2 with brake
Tools Required:
Rubber mallet
LT45PC
TOP VIEW
Front door faces away from bottom
platform as pictured above.
2
With bottom shelf facing up push all four 18” legs
onto leg posts. Using rubber mallet hammer legs
firmly into position. Legs must be seated (flush)
against the shelf surface. Place rubber band
around legs to aid in the assembly of cabinet
side panels and doors.
CENTER
SHELF
6
Begin seating of center shelf by holding door panel,
leg and side panel as illustrated. Gently tap corner
post into leg. Repeat on all 4 sides until all posts
are partially inserted into legs. Now repeat hammering action more firmly going around to each
shelf post and driving the leg posts more securely
into the legs.
Top of panels and door frame must be nested into
the underside of the center shelf lip in the same
manner as the bottom shelf.
BOTTOM
SHELF
SIDE VIEW WITH
LEG POST
3
Install the side panels first. Slide panels down
between legs until they are nested inside the
shelf lip and flush against the shelf surface.
Rubber band will hold legs and side panels in
place while installing back panel and front door.
7
Install top legs onto middle shelf.
and cord wrap before keyboard shelf (see reverse)
keyboard runners onto legs with tab toward the direction the
shelf pulls out which should be the opposite side of the cabinet
door. (See diagram)
Thread allen set screws into runners.
Using allen wrench, tighten set screws until runners are
secured. Take shelf runner adapter brackets and secure to
pullout shelf using 1/2” sheet metal screws. NOTE: Adapter
brackets have a hole on end, this is the front of the bracket.
That hole must be on the side of the shelf with the rounded
edge.
Next, take shelf and slip rear of adapter bracket under tab on
runner. Front of adapter has hole that goes over black locking
tongue. Push down until it snaps into place.
Install electric assembly
PANEL SEATED
INSIDE SHELF LIP
. Insert
Set shelf height as desired
then tighten allen head set
screws to secure
Shelf runner adapter
Allen head
set screw &
wrench
4
Install the back panel in the same manner as
shown in Step #3. NOTE: Cabling hole in back
panel should be toward the top.
Pull out
shelves
Runner
Screws
5
Install door panel same as back panel, with
door handle at top.
CORD
GUIDE
COVER
TOP
SHELF
CENTER SHELF
GROMMET CAP
GROMMET RING
8
Place top shelf (with handle) onto legs. Insert leg
posts into legs of top shelf. Using rubber mallet,
firmly hammer top shelf into legs until all four legs
are seated against shelf surface. install grommet
ring and grommet cap into top of shelf. For tables
with electric assembly, snap off cord guide cover
form grommet cap to allow equipment plug to be
run through grommet. Insert grommet cap into
grommet ring. Remove rubber band.
6
Insert two bolts into pre-drilled holes on inside of
back panel and fasten with nuts.
PLACE LOCKING CASTERS
AS ILLUSTRATED
BACK
FRONT
9
Push the four casters firmly into the holes in
each corner of the bottom shelf. Important: casters must be fully seated. Tap firmly with rubber
mallet to properly seat casters. Turn your
Endura Table right side up.
Loading...