Luxor|H.Wilson LPDUO User Manual
Instruction Sheet - LP Model Tables
Models LP-26 and LP-27 Two Shelf Mobile Tables
Models LP-34, LP-40, LP-42, LP-48 and LP-54 Three Shelf Mobile Tables
Customer Service Dept
2245 Delany Rd
Waukegan, IL 60087
Ph: 847/244-1800 • 800/323-4656
Fax: 847/244-1818 • 800/327-1698
Two Shelf Model
LP -
Three Shelf Model
LP -
PARTS LIST
Models LP26 & LP27
1 - Bottom shelf with casters sockets
- Top shelf with handle
1
4 - Long legs
4 - Casters (2 w/brake)
1 - Plug housing cover
- Sheet metal screws
2
Optional Electric Assembly:
1 - Electric cord
1 - Power cord retaining bracket
1 - Cord tie
3 - Sheet metal screws
Models LP34, LP40, LP42,
LP48 & LP54
- Bottom shelf with casters sockets
1
1 - Top shelf with handle
1 - Center shelf with eight leg posts
4 - Short legs
- Long legs
4
4 - Casters (2 w/brake)
- Plug housing cover
1
2 - Sheet metal screws
Tools Required:
1 - Rubber Mallet
1 - Slotted Screwdriver
IMPORTANT:
If your LP table does not have the Optional
Electrical Assembly start by closing the electr
ic plug housing in the handle of the top shelf
as illustrated. If your LP table has the Optional
ic Assembly, see assembly instructions
Electr
below. Start by assembling electric.
CORD
RETAINING
TRACK #1
A
CORD MANA
TIE IS IN SECURED
POSITION
GEMENT TIE
3 PLUG UNIT
PLUG
HOUSING
COVER
CORD
RETAINING
TRACK #2
POWER CORD PLUG
RETAINING BRACKET
1
Firmly seat electrical assembly 3 plug unit into
handle plug housing as illustrated. Secure with
power cord plug retaining bracket.Thread cord
through cord retaining tr
ing in the side of the handle.
ack and out the open-
Models LP-26 and LP-27
LONG LEGS
LEG POST
1
Lay top shelf (with handle) ribbed side up on a
smooth surface. Push all 4 legs onto leg posts.
2
Position bottom shelf, ribbed side up, over the 4
legs and insert leg posts into legs. Using a
rubber mallet, firmly hammer bottom shelf into
legs until all 4 legs are seated (flush) against the
surfaces of both shelves.
*Models LP34 and LP40
use long legs second.
*Models LP42, LP48 and
LP54 use short legs second.
FOR BIG WHEEL
ASSEMBLY.
See instructions
in Big Wheel
hardware pack.
PLACE LOCKING CASTERS
AS ILLUSTRATED
BACK
FRONT
3
Push the four casters firmly into the holes in
each corner of the bottom shelf. Important:
Casters must be fully seated. Tap firmly with
rubber mallet to properly seat casters. Turn your
LP table right side up. It is now ready for use.
Models LP-34, LP-40, LP-42, LP-
48 and LP-54
*Models LP34 and LP40 use short legs first.
*Models LP42, LP48 and LP54 use long legs first.
LEG POST
1
Models LP-34 and LP-40: La
handle) ribbed side up on a smooth surface.
Push all 4 short legs onto leg posts.
Models LP-42, LP-48 and LP-54: Lay top
shelf (with handle) ribbed side up on a smooth
surface. Push all 4 long legs onto leg posts.
FOR BIG WHEEL
ASSEMBL
See instructions
in Big Wheel
hardware pack.
Y.
PLACE LOCKING CASTERS
y top shelf (with
AS ILLUSTRATED
POWER CORD
MANAGEMENT TIES
3
Wrap the cord
around the
handle.
2
Secure po
hole with sheet metal screws. See illustration
A. Secure with power cord management tie by
wrapping tie around cord and fastening. Cut off
y unnecessary extra length of tie.
an
wer cord management tie into starter
4
For safety and neat
appearance secure cord
plug to cord by utilizing
plug snap.
2
Position center shelf (with 8 leg posts) ribbed
side up, over the 4 legs and insert leg posts into
legs. Using a rubber mallet, firmly hammer center shelf into legs until all 4 legs are seated
(flush) against the surf
aces of both shelves.
3
Push remaining 4 legs into leg posts of center
shelf.
4
Position bottom shelf, ribbed side up, over the 4
legs and insert leg posts into legs. Using a
rubber mallet, firmly hammer bottom shelf into
legs until all 4 legs are seated (flush) against the
surfaces of both shelves.
BACK
FRONT
5
Push the f
each corner of the bottom shelf. Important:
Casters m
rubber mallet to properly seat casters. Turn
your LP table right side up. It is now ready for
use.
our casters firmly into the holes in
ust be fully seated. Tap firmly with
Loading...