Flat Panel Series Mobile
Stand Instructions
09/23/13
TYPE1
Stationary Mount Base Model
TYPE3
Stationary Mount + Shelf +
Camera Mount
TYPE2
Stationary Mount + Shelf
TYPE4
Rotating Mount + Shelf
Table of Contents
Table of Contents and Warnings ............................ 2
Part List ............................................... 3
Assembly and Installation
Adjust upper and lower poles .............................. 4
Attaching to the base assembly ............................5
Install steel cross rods .................................... 6
Height adjustment ....................................... 6
Media shelf assembly .................................... 7
Assemble at panel mount ................................ 8-9
Install mount to the frame ................................. 10
Install camera mount ..................................... 11
Cable and wire installation ................................ 11
VESA mounting patterns .................................. 12
Tools Required
- Phillips Screwdriver
- Wrench
WARNING!
Severe personal injury and property damage can result from improper installation. Read
instructions carefully before beginning.
• If you do not understand the instructions or have any concerns please contact a
qualied local installer.
• Do not install or assemble if the product or hardware is damaged or missing, if you
require replacement parts contact your local dealer.
• This product ts most 40˝- 60˝ at panel displays; maximum weight for the display
is 100 lbs. / 45.5kg.
• Do not use this product for anything other than what it was originally designed.
• This product contains moving parts, please use caution.
• The manufacturer disclaims any liability for the modications, improper installation
and installation exceeding maximum weight capacity. The manufacturer will not be
liable for any damages arising out of the use of, or inability to use the product.
2 / 12
Part List
TYPE1, TYPE2, TYPE3
TYPE4
A1 x1
A2 x4
A3 x4
A4 x1
TYPE1, TYPE2, TYPE3
C1 x1
C2 x2
C3 x2
R2 x1
B3 x2
(B3 is preinstalled)
B4 x4
TYPE4
C1 x1
R3 x1
*1 is pre-installed
C4 x4C5 x4
B2 x2
B1 x1
B5 x2*
C3 x4
S2 x1
B2 x2
B1 x1
B5 x2
C2 x2
D x2
only: TYPE2,
TYPE3, TYPE4
M8x25mm
M6x25mm
R1 x1
M5x25mm
H x4 J x4
M8x20mm
M6x10mmM5x10mm
K x4 L x1 M x1T x8N x2 P x2
only: TYPE3
only: TYPE1,
TYPE2, TYPE3
only: TYPE3
E x4 F x4G x4
only: TYPE2,
TYPE3, TYPE4
S1 x1
only: TYPE3
3 / 12
Adjust upper and lower poles
1
Locate the spring plungers inside the bottom grommet hole of pole
B1 (If your unit has B5 cross bar pre-installed remove prior). Starting
1
with the right side pole B2, push the spring plunger down and pull
B2 up slightly and twist it slightly so that the spring plunger remains
offset. This will make adjusting the pole easier. (gure 1)
Hold the poles B1 & B2 with your hands and use your left foot on
2
the cross bridge of B1 for stability. Pull B2 upward until you reach
your desired height. Twist B2 so that the spring plunger locks into
the nearest spring plunger hole. (gure 2)
Repeat the same steps for the left side pole B2 but use your
3
right foot for stability instead. Align poles B2 and lock the spring
plunger into place. (gure 3)
Only for TYPE1, TYPE2, TYPE3
Remove B5
B5
before step 1.
B2 B2
B2
B1
Spring
plunger
4 / 12
B2
B3 is
pre-installed
B1
Spring
plunger
B1
gure 1 gure 2 gure 3
Lift pole assembly so that the part remains upright and the
cable management holes are facing toward you.
Attaching to the base assembly
2
Thread casters A2 and washer A3 into the bottom of base A1. Make
1
sure all casters are locked to prevent movement during installation.
With allen wrench M attach lower poles B1 to base A1 with screw K.
2
First through the bottom of base A1, then through the top of base A.
After screws K are rmly fastened, push down the screw cover A4
3
until it locks into place.
2
cable management
holes facing back
K
B1
A3 A3
A2
A3
A2
1
Lock Casters
before assembly
A2
A2
Tighten Fully
with wrench
A1
A3
B1
2
1
K
M
3
A4
A1
5 / 12
Install steel cross rods
3
B5
1
Phillips
screwdriver
B2
B5
B5
2
B5
3
Remove the pre-installed
screws on rod B5. Making
sure the upper poles B2
are aligned, slide rods B5
into the top openings.
Height adjustment
4
B4
Assistance
Required
Cables
Unplugged
⁄2˝ H / 1050mm - 1500mm
1
Refasten rods B5
with screws.
Slide the upper poles B2 up or down
to the different spring plunger holes for
your desired height. Install grommet
covers B4 into the grommet holes.
B4
6 / 12
⁄2˝ - 62
1
46
B4
B4
Press and hold both spring
plungers to slide the upper
poles B2.
Media shelf assembly (TYPE2, TYPE3, TYPE4)
5
Before assembly make sure
there is enough clearance for
the at panel display
1
R2
2
1
B1
Remove the pre-installed screws
on bracket R2. Align bracket R2
to desired position and clamp R2
then retighten the long screws.
L
Phillips
screwdriver
2
1
R2
Using the short screws fasten
bracket R2 to support R3.
R3
Phillips
screwdriver
3
R1
R3
2
With allen wrench L and the
short allen screws fasten
shelf R1 to support R3.
7 / 12
6a
Assemble at panel mount (TYPE4)
VESA: 200x400 - 400x400mm
1
C1
C2
C2
Top of Display
3
C2
Display
not included
F
E
G, H, J
3. C4
2. C2
C2
1. C3
2
C1
For a selection of mounting
positions refer to page 12
First unscrew and remove
the vertical supports C2 from
mount C1.
Align the screw threads C3 to
the desired vertical support
position of C2. Screw support
C2 into C1 and C3. Insert
support stoppers C4 followed
by caps C5.
4. C5
Phillips
screwdriver
VESA: 400x600 - 500x800mm
M8x25mm (G)
G
G
F
F
Safety Precautions
8 / 12
M5x25mm (H)
M6x25mm (J)
E
F
H,J
Carefully attach mount to
display using screws G,H or J.
Through washer E, support C2
and spacer F.
Phillips
screwdriver
H,J
E
F
Plastic spacers must
be used to avoid any
damage from screws
Adjusting the mount (TYPE4) - After Step 7
Remove pre-installed screws
Re-attach screws
C1
Phillips
screwdriver
6b
Assemble at panel mount (TYPE1, TYPE2, TYPE3)
VESA: 200x200mm VESA: 200x200 - 600x400mm
Phillips
screwdriver
Swivel
90°
C1
E
F
H, J
M5x25mm (H)
M6x25mm (J)
H,J
E
F
Safety Precautions
H,J
E
F
Phillips
screwdriver
T
E
F
H, J
T
9 / 12
Install mount to frame
7
1
Make sure casters
are locked prior to
installation
Lift up lock hook
2
before installing
mount
C1
3 4
Heavy Lifting:
Assistance
Required
Attach hooks on C1
onto cross rods B5
C1
B5
10 / 12
Secure lock hook fully
Lock not included
Install camera mount (TYPE3)
8
S1
S2
Adjustable height
Cable and wire Installation
9
Please use care when
inserting the wires and
cables into the grommet
to avoid damage
N
P
Phillips
screwdriver
For indoor use only.
Avoid excessive wind,
heat & humidity.
11 / 12
10
09/23/13
VESA mounting patterns
Slide vertical support rails
to nd the best assembly
position for your display.
12 / 12
D
For 200x200mm VESA mounting position use brackets D.
Loading...