LUXOMAT PD4-M-TRIO-2DALI/DSI-1C-SM, PD4-M-TRIO-2DALI/DSI-1C-FC Installation And Operating Instruction

Installation and Operating Instruction for B.E.G.-Occupancy detectors PD4-Master-TRIO-2DALI/DSI-1C-SM/-FC

A circular opening
of diameter 100mm
must be produced in
the ceiling.

Having connected
up the cables in
accor dance with
regulations, the
detector is inserted
into the opening as
shown and fixed
into position with
the retaining bracket
using screws.

A Light sensor 1 | B Light sensor 2
1 LED red OFF function
2 LED green too bright/too dark CDS 1
3 LED white semi-automatic DA 1/2
4 LED white semi-automatic Channel 3
5 LED green too bright/too dark CDS 2
6 LED red motion indicator/walking test

2a. Installation of the LUXOMAT®

PD4-M-TRIO-2DALI/DSI-1C-SM

2b. Installation of the LUXOMAT®

PD4-M-TRIO-2DALI/DSI-1C-FC

3. Hardware configuration

Position of light sensors and LEDs

The detector must be in stalled on a solid and
level surface. The circular cover ring must be removed
prior to assembly. To do this, twist the lens (C) anti­clockwise through approximately 5° and lift off.

Having connected up the wires in accordance with
regulations, secure the detector with 2 screws.
After installation replace the lens and lock (turn
clockwise). Mains to be connected.

4. Putting into operation
of the remote control
(optional)

Remote control
LUXOMAT® IR-PD4-TRIO-DALI

1. Check Battery:

open battery compartment by pressing
the plastic springs together and remov­ing the battery-holder.

Caution:
Settings with remote control supersede
the settings by courtesy of potentiom­eters.

LUXOMAT

®

PD4-M-TRIO-2DALI/DSI-1C

1. Mounting preparations

Work on the 230V mains supply
may only be carried out by quali­fied professionals or by instructed
persons under the direction and
supervision of qualified skilled elec­trical personnel in accordance with
electrotechnical regulations.

Disconnect supply before installing!

When in Master/ Slave mode of
operation, the Master-appliance
must always be installed at the
location where there is least
daylight.

Option:

Wall bracket for remote
control

IR-PD4-TRIO-DALI

A4 5 1 3 2 6

B

GB

6. Putting into operation / Settings

Self test cycle

After an initial 60-second self-test cycle, the LUXOMAT® PD4-M-TRIO-2DALI/DSI-1C is
ready for operation.

Potentiometer 3: Follow-up time for light control

The time can be set infinitely variably at between 1 and 60 minutes. The
time-setting is valid for all three channels of the PD4-M-TRIO-2DALI/DSI-1C.

Symbol TEST: Test mode (Every movement switches on the light for a period
of 2 second, switching it off for a period of 2 seconds after that regardless
of the level of brightness.)

Potentiometer 2: Twilight-switch for light control

The switch-on value for the light can be set at between 40 and 1200Lux.
Using the rotary control, the luminance set points can be set as desired.

Symbol : Night-time operation | Symbol : Daytime/ Night-time operation

Potentiometer 1: Orientation lighting

This rotary controller serves to determine the working time of the orientation
lighting (fixed to 20%).

“ON” for permanent orientation lighting.
“OFF” for deactiviation of orientation lighting.

Pulse spacing PD-Slave

2 or 9 seconds can be set for the pause between 2 pulses sent to the master.
The setting can be made with activated ( ) or deactivated ( ) LED indicator.

For devices with a separate slave input, 2sec. can be set.

45

30

15

5

1

TEST

60

1200

600

200

40

60

5

15

30

45

ON

OFF

80 - 90 mm

100 mm

open

close

C

Explanation of the key functions

6
5

4
A
3
2
1

B

DIP 1 HA / A
DIP 2 Ini OFF/ON

Lamps at start-up OFF/ON
DIP 3 RESET

5. Position of potentiometer and DIP switch

SM

FC

3

1

2

DIP

123

DIP
321

123

SM FC

9s 2s

LED ON

LED OFF

DA 1/2 ON/OFF when locked
(=> see page 2, point 9)

Dimming

when locked

=> (

see page 2, point

8)

Activate test mode – when locked
Deactivate test mode: press Reset

Resetting when locked

The lighting relay is switched off, i.e. opened and the follow-up times
reset.

Permanent protection against sabotage

This function blocks the unit permanently (green LED is illuminated).
This operating mode can only be activated during the period of 5
seconds after pressing the “lock“ button. This status will only permit
actuating the function “Light on/Light off”.
The procedure for leaving this mode is as follows:

reset the hardware

using DIP switch 3 or switch the supply voltage as follows:

Dimming in opened state
The following approach will prove useful when setting a command value
(example workplace): Place a luxmeter flat on the desk, then, using the
remote control IR-PD4-TRIO-DALI, adjust the light up or down by pressing
the keys “max“ or “min“ until the desired command value which best
suits your requirements has been reached.

Saving of the through adjusted luminance set point

100 h function in opened state

to extend the life span – sums up automatically the burning time of
100% luminosity at the beginning up to 100 hours – only then can
lights dim

Orientation lighting and its follow-up time ON/OFF
Note: During the orientation light phase, the constant light regulation is

also active: if there is sufficient brightness, dimming occurs < 2V and,
if applicable, the lighting is switched off.

Orientation lighting – Adjustment ot the light intensity

The orientation lighting is adjustable in a span from 10 to 30% of the
nominal light. Standard adjustment is 20%.

t < 5 sec.

100

h

Settings by remote control

Unlocking device





60





10

to

or

Dimming of the luminance set
point (only for channel 1 and 2)

to

60

min

1

min

Follow-up time light

optionaloptionaloptionaloptional optional

100 h function
=> (see page 2, point 19)

Orientation lighting

ON = all LEDs ashes 2x
OFF = all LEDs ashes 1x

Follow-up time
orientation lighting

Orientation lighting
10 – 30% of nominal light

Luminance set point for
constant light regulation

to

or

Fully automatic/semi automatic mode

(only DA1/2) => (see page 2, point 10)

LED display ON/OFF

Sun button – preselected light
value (Daylight operation)

1000100

or

Saving of the dimmed
luminance set point

Resetting
when open:

All values
which have
been pro­grammed us­ing the remote
control are
deleted, and
those values
which have
been set by
potentiometer
are activated.

Locking device – Exit
programming mode

Permanent protection against sabotage

LED ashes

or

t < 5 sec.

DA 1/2 ON/OFF

optional

Switching between DALI and DSI
(factory settings DALI)

optional

Switching

Channel 1C between HVAC-

and light control (

factory settings

light)

ON

230 V

1sec. 1sec.30 sec. - 60sec.

OFF

15.

Technical data

PD4-M-TRIO-2DALI/DSI-1C

Sensor and power supply in one case

Power supply: 230V~ ±10 %
Power consumption: < 1W
Ambient temperature: -25°C to +50°C
Degree of protection/class: IP20 / II
Settings: control dial, DIP switch and

remote control

Light values - Remote control:

100 - 1000Lux

Extension of the detection area: with Slaves

Area of coverage: circular 360°
Range of coverage Ø H 2.50m / T= 18°C:

seated 6.40m / tangential 24m / radial 8m

Recommended height for mounting: 2 - 3 m
Light measurement: mixed light, daylight + artificial

light, suitably for constant light
control

Light values - Potentiometer:

10 - 2000Lux

• Dali output DA 1/2 for light switching, light-controlled
Max. numbers of connected EB‘s: each 25 for DA1 and DA2

•

Channel 1C (-1C)

for light switching (panel lighting

), light- or
motion-controlled or HVAC circuit, only motion-controlled
Type of contact: NOC/with pretravel tungsten contact
Contact load

: 3000 W, 230V~, 16A cos ϕ=1 /

1500VA cos ϕ= 0,5, μ-Contact

Time-settings Channel 1C: 1 - 60 min. / Test
Dimensions H x Ø [mm] SM FC
124 x85 100 x 117

Visible portion when built into ceiling: H 37 x Ø 117mm

Technical data PD4-Slave

Power supply: 230 V~ ±10%
Impulse output: Optocoupler max. 2W
Impulse duration: 2sec. or 9sec.
Dimensions: SM FC

76 x 101 97 x 103
Visible portion when built into ceiling: 34x10mm

Declaration of Conformity: The product complies with

the low voltage recommendation 2006/95/EC and the EMV
recommendation 2004/108/EC.

14. Connections

Type SM FC FM

PD4-M-TRIO-2DALI/DSI-1C
(Master)

92751 92756 –

PD4-S (Slave) 92142 92254 9 2163

LUXOMAT

®

Remote control:

IR-PD4-TRIO-DALI (incl. wall bracket) 92104

Accessory:

SM-Socket IP44 for 92751 92386
Wire basket BSK 92199
Wall bracket for remote control as replacement 92100

12. Article / Part nr. / Accessory

In case the sensing area of the LUXOMAT® PD4-M-TRIO­2DALI/DSI-1C is too large or areas are being covered that
should not be monitored, the range can be reduced or
limited through use of the enclosed masking clips (e).

11. Exclude sources of interference

10. Range of Coverage

8. Manual Dimming

(for IR-PD4-TRIO-DALI functions see page 1)

You can dim manually by pressing the pushbutton for a long
time (> 2 sec.). When the button is released, the current dim­ming value is retained. Upon renewed dimming, the dimming
direction is reversed.

7. Fully/Semi automatic mode

(see DIP switch functions and IR-PD4-TRIO-DALI on page 1)

Automatic operation

In this operating mode, the lighting switches
automatically on and off for increased comfort,
depending on presence and brightness.

Semiautomatic operation

In this operating condition, in order to gain
increased savings, the lighting is energized only after
being manually switched on. Switch-off takes place
automatically.

The semiautomatic mode basically behaves like the fully
automatic one. However, the difference is that switching­on must always be carried out manually!

As many (closer-contact) buttons as desired can be wired
in parallel on the “S” button input (ON/ OFF DIM).

9. Manual Switching

You can switch the lighting on and off manually by
pressing the pushbutton for a short time. It will stay
on or off as long as people are detected plus the

congured follow up time.

16. DIP switch functions

PD4-M-TRIO-2DALI/DSI-1C

1

2

Walking across
Walking towards
Seated

quer zum Melder gehen
frontal zum Melder gehen
sitzende Tätigkeit

DIP
switch

OFF ON

1 (A) Fully automatic channel

DA 1/2 + HVAC/Light

Semi-automatic channel
DA 1/2 + HVAC/Light

2 (B) For mains ON /

light ON

For mains ON /
light OFF

3 (C) Standard operation RESET

17. LED function displays

18. Fault-finding

Permanently flashing

Check whether DIP3 switch (RESET)
is set to “ON”

Reset to “OFF” if necessary

DIP

ON

OFF

1 2 3

LED Colour Function Display

6 red Motion indicator Lights up for motion

detection

5 green Light status indica-

tor DA 1

flashes twice per sec.:

-

bright enough (light
OFF)/ too bright (light
ON)

flashes once per sec.:

- Delay time active

4 white HA/VA Channel

1C

lights when semi-automatic

3 white HA/VA DA 1/2

lights when semi-automatic

2 green Light status indica-

tor DA 2

flashes twice per sec.:

-

bright enough (light
OFF)/ too bright (light
ON)

flashes once per sec.:

- Delay time active

1 red OFF-function lights when the feature

is activated, ie in the
initialization phase the
light is off

all LEDs Acknowledgement flashes once per sec.:

- correct input

flashes twice per sec.:

- incorrect input

flashes three times / once
per sec.:

- Reset when locked

flashes three times / twice
per sec.:

- Double locked

light up for 2sec.:

- HVAC mode Channel
1C active

light up for 0,5sec.:

- Light control mode
Channel 1C active

all LEDs Status flashes shortly once per

sec.:

- Detector is double locked

MAN 7603 – 270213–2

WE RECOMMEND THAT BEFORE DIMMING OF THE CONNECTED LIGHTS A
100 h BURN IN (T5 TUBES OR 80 HOURS FOR T8 TUBES) FUNCTION TAKES
PLACE. THIS CAN BE IGNORED BY USING THE REMOTE CONTROL TO DEACTI

­VATE. THE LIFESPAN OF THE LAMPS CAN BE REDUCED IF THE BURN IN DOES
NOT TAKE PLACE.

13. Wiring diagram – Standard mode with Master-TRIO-2DALI/DSI-1C occupancy detectors

optional

T1&2 = NO button for semi-automatic mode
Slave for enlargement of detection area

MASTER SLAVE

E1 DALI

L

N
DA
DA

L

N

E2 DALI

L

N
DA
DA

HVAC/LIGHT

L

N

RNO NO

S

S

+-+

DA1/2

HVAC/
Light

HVAC/

Light

DA1 DA2

NLR

T2

T1

LN

–

DA2+DA1

+

S

LiGht

NONO

PD4-M-TRIO-2DALI/DSI-1C-FC

PD4-M-TRIO-2DALI/DSI-1C-SM

L

N

R

Slave

T1T2

DA –
DA +

DA –
DA +

L

N

R

Slave

T2

DA –
DA +

DA –
DA +

NO

L

NO

L N N S S

R

T1

S

hVAC

R

–

DA1+DA2

+

1

2

12 m

12 m

8 m

6.40 m

24 m

360°

2.50 m

e