Luxibel LXMH10001 User Manual

LXMH10001

36 X 10 W OSRAM LED RGBW MOVING HEAD

USER MANUAL

LXMH10001

V. 02 – 01/03/2016 2 ©Velleman nv

LXMH10001

V. 02 – 01/03/2016 3 ©Velleman nv

USER MANUAL

1. Introduction

To all residents of the European Union
Important environmental information about this product

This symbol on the device or the package indicates that disposal of the device after its lifecycle
could harm the environment. Do not dispose of the unit (or batteries) as unsorted municipal
waste; it should be taken to a specialized company for recycling. This device should be returned
to your distributor or to a local recycling service. Respect the local environmental rules.

If in doubt, contact your local waste disposal authorities.

Thank you for choosing Luxibel®! Please read the manual thoroughly before bringing this device into
service. If the device was damaged in transit, do not install or use it and contact your dealer.

2. Safety Instructions

Be very careful during the installation: touching live wires can cause life-threatening
electroshocks.

Always disconnect mains power when device not in use or when servicing or
maintenance activities are performed. Handle the power cord by the plug only.

Indoor use only. Keep this device away from rain, moisture, splashing and dripping
liquids. Never put objects filled with liquids on top of or close to the device.

Keep this device away from children and unauthorized users.

Caution: device heats up during use.

Do not stare directly at the light source, as this may cause

 epileptic seizure in sensitive people
 temporarily loss of sight (flash blindness)
 permanent (irreversible) eye damage.

There are no user-serviceable parts inside the device. Refer to an authorized dealer for
service and/or spare parts.

Respect a minimum distance of 0.5 m between the device’s light output and any
illuminated surface.

This is a Safety Class 1 device. It is therefore essential that the device be earthed.
Have a qualified person carry out the electric connection.

 Make sure that the available voltage does not exceed the voltage stated in the specifications of this

manual.

 Do not crimp the power cord and protect it against damage. Have an authorised dealer replace it if

necessary.

 Use an appropriate safety cable to fix the device (e.g. VDLSC7N or VDLSC8N).
 Install the device at a minimal distance of 0.5 m from flammable and explosive objects or

substances.

 The maximum ambient temperature is 40 °C. Do not operate the device at higher temperatures.

LXMH10001

V. 02 – 01/03/2016 4 ©Velleman nv

3. General Guidelines

Refer to the Velleman® Service and Quality Warranty on the last pages of this manual.

Keep this device away from dust and extreme temperatures. Make sure the ventilation
openings are clear at all times. For sufficient air circulation, leave at least 1" (± 2.5 cm)
in front of the openings.

Protect this device from shocks and abuse. Avoid brute force when operating the
device.

 Familiarise yourself with the functions of the device before actually using it. Do not allow operation

by unqualified people. Any damage that may occur will most probably be due to unprofessional use
of the device.

 All modifications of the device are forbidden for safety reasons. Damage caused by user modifications

to the device is not covered by the warranty.

 Only use the device for its intended purpose. All other uses may lead to short circuits, burns,

electroshocks, lamp explosion, crash, etc. Using the device in an unauthorised way will void the
warranty.

 Damage caused by disregard of certain guidelines in this manual is not covered by the warranty and

the dealer will not accept responsibility for any ensuing defects or problems.

 Mechanical wear and LEDs are not covered by warranty.
 A qualified technician should install and service this device.
 Do not switch the device on immediately after it has been exposed to changes in temperature.

Protect the device against damage by leaving it switched off until it has reached room temperature.

 This device is designed for professional use on stage, in discos, theatres, etc. The device should only

be used indoors with an alternating current of 100-240 V~, 50/60 Hz.

 Lighting effects are not designed for permanent operation: regular operation breaks will prolong their

lives.

 Use the original packaging if the device is to be transported.
 Product images are for illustrative purposes only.
 Keep this manual for future reference.

4. Features

 DMX channels: 16/26/15/17
 super-fast, smooth and silent movement
 four-colour RGBW mixing to create vivid, saturated and uniform colour effects
 pre-set colour temperature at 2700 K, 3200 K, 4200 K, 5600 K and 8000 K
 zoom from 13° to 60°
 full-range 0-100 % dimmer
 various strobes
 software upgrade via DMX
 hibernation when lost DMX for preset time
 indicate temperature info of base, arm and lamp
 fan speed auto-change according to temperature
 16-bit resolution
 auto repositioning

LXMH10001

V. 02 – 01/03/2016 5 ©Velleman nv

5. Mounting and Connection

Choose a suitable mounting spot. Mount the device in the desired angle using the included bracket.
Connect the power cord to the mains. Disconnect after use.

5.1 Mounting the Device

 Have the device installed by a qualified person, respecting EN 60598-2-17 and all other applicable norms.
 The carrying construction must be able to support 10 times the weight of the device for 1 hour

without deforming.

 The installation must always be secured with a secondary attachment e.g. a safety cable.
 Never stand directly below the device when it is being mounted, removed or serviced. Have a

qualified technician check the device once a year and once before you bring it into service.

 Install the device in a location with few passers-by that is inaccessible to unauthorised persons.
 Overhead mounting requires extensive experience: calculating workload limits, determining the

installation material to be used… Have the material and the device itself checked regularly. Do not

attempt to install the device yourself if you lack these qualifications as improper installation may
result in injuries.

 For truss mounting, use an appropriate clamp (not incl.) and fit an M10 bolt through the centre of the

(folded) bracket.

 Adjust the desired inclination angle via the mounting bracket and tighten the bracket screws.
 Make sure there is no flammable material within a 0.5 m radius of the device.
 Have a qualified electrician carry out the electric connection.
 Connect the device to the mains with the power plug. All devices must be powered directly off a

grounded switched circuit. Do not connect to a dimmer pack.

 The device has a power output to supply power to another device. When connecting several devices

in a daisy chain via this output, make sure that the total current does not exceed the power line’s
nominal current. Use power cables with an adequate section.

 The installation has to be approved by an expert before the device is taken into service.

1. Install the clamp onto the Omega bracket.

2. Install the clamp-bracket assembly onto the device.

3. Install the assembly onto an appropriate truss and fasten. Secure with a secondary safety rope.

5.2 Connecting the Device

Power

Connect the device to the mains with the power plug.
Power all devices directly off a grounded switched circuit.
Do not connect the device to a rheostat or dimmer circuit, even when using the rheostat or dimmer

channel solely for 0 % to 100 % switching.

 Have a qualified electrician carry out the electric connection.