Luxibel LX116 User Manual

LX116

PIXMOVE 12 - 12 X 8 W RGBW LED WITH TILT MOVEMENT

USER MANUAL

LX116

V. 02 – 22/10/2014 2 ©Velleman nv

terminator

How to turn the controller line from 3-pins into 5-pins (plug and socket).

LX116

V. 02 – 22/10/2014 3 ©Velleman nv

USER MANUAL

1. Introduction

To all residents of the European Union
Important environmental information about this product

This symbol on the device or the package indicates that disposal of the device after its lifecycle
could harm the environment. Do not dispose of the unit (or batteries) as unsorted municipal
waste; it should be taken to a specialized company for recycling. This device should be returned
to your distributor or to a local recycling service. Respect the local environmental rules.

If in doubt, contact your local waste disposal authorities.

Thank you for choosing Luxibel®! Please read the manual thoroughly before bringing this device into
service. If the device was damaged in transit, do not install or use it and contact your dealer.

2. Safety Instructions

Be very careful during the installation: touching live wires can cause life-threatening
electroshocks.

Always disconnect mains power when device not in use or when servicing or
maintenance activities are performed. Handle the power cord by the plug only.

Indoor use only. Keep this device away from rain, moisture, splashing and dripping
liquids. Never put objects filled with liquids on top of or close to the device.

Keep this device away from children and unauthorized users.

Caution: device heats up during use.

Do not stare directly at the light source, as this may cause

 epileptic seizure in sensitive people
 temporarily loss of sight (flash blindness)
 permanent (irreversible) eye damage.

There are no user-serviceable parts inside the device. Refer to an authorized dealer for
service and/or spare parts.

Respect a minimum distance of 0.5 m between the device’s light output and any
illuminated surface.

This is a Safety Class I device. It is therefore essential that the device be earthed. Have
a qualified person carry out the electric connection.

 Make sure that the available voltage does not exceed the voltage stated in the specifications of this

manual.

 Do not crimp the power cord and protect it against damage. Have an authorised dealer replace it if

necessary.

 Use an appropriate safety cable to fix the device (e.g. VDLSC7N or VDLSC8N).
 Install the device at a minimal distance of 0.5 m from flammable and explosive objects or

substances.

 The maximum ambient temperature is 40 °C. Do not operate the device at higher temperatures.

LX116

V. 02 – 22/10/2014 4 ©Velleman nv

3. General Guidelines

Refer to the Velleman® Service and Quality Warranty on the last pages of this manual.

Keep this device away from dust and extreme temperatures. Make sure the ventilation
openings are clear at all times. For sufficient air circulation, leave at least 1" (± 2.5 cm)
in front of the openings.

Protect this device from shocks and abuse. Avoid brute force when operating the
device.

 Familiarise yourself with the functions of the device before actually using it. Do not allow operation

by unqualified people. Any damage that may occur will most probably be due to unprofessional use
of the device.

 All modifications of the device are forbidden for safety reasons. Damage caused by user modifications

to the device is not covered by the warranty.

 Only use the device for its intended purpose. All other uses may lead to short circuits, burns,

electroshocks, lamp explosion, crash, etc. Using the device in an unauthorised way will void the
warranty.

 Damage caused by disregard of certain guidelines in this manual is not covered by the warranty and

the dealer will not accept responsibility for any ensuing defects or problems.

 Mechanical wear and LEDs are not covered by warranty.
 A qualified technician should install and service this device.
 Do not switch the device on immediately after it has been exposed to changes in temperature.

Protect the device against damage by leaving it switched off until it has reached room temperature.

 This device is designed for professional use on stage, in discos, theatres, etc. The device should only

be used indoors with an alternating current of 240 VAC, 50 Hz.

 Lighting effects are not designed for permanent operation: regular operation breaks will prolong their

lives.

 Use the original packaging if the device is to be transported.
 Keep this manual for future reference.

4. Features

The PIXMOVE 6 is a newly designed motorized linear LED luminaire in the Prolights range. It is conceived
to achieve high-brightness and versatility. The LX116 has 6 x 8 W RGBW LEDs that can be controlled in
pixel-to-pixel mode, with 250° motorized tilt inclination through DMX. Several pre-programmed dynamic
effects are available in the internal memory, which can be combined with multiple reproduction methods
and colour macros. This PIXMOVE 6 is perfect for architectural constructions on stage.

 12 x 8 W RGB high-power LEDs
 motorized tilt axis with rotation to 250°
 auto mode with presets for automatic programmes with speed control
 master/slave mode for stand-alone operations
 DMX controlled from basis to advanced modes

o 6-channel mode: RGBW, tilt, tilt speed
o 8-channel mode: RGBW, dimmer, shutter, tilt, tilt speed
o 10-channel mode: RGBW, shutter, macro, auto, auto speed, dimmer, tilt, tilt speed
o 26-channel mode: RGBW for each pixel, tilt, tilt speed

 colour temperature presets from 3200 K to 10000 K
 static reproduction of a colour via stand-alone mode
 flicker-free (400 Hz)
 power and signal link via powerCON and 3-pin XLR