Luxibel LX113 User Manual

LX113

2 X 2 MATRIX PANEL WITH HIGH OUTPUT TRI-COLOUR LEDS –
KLING-NET / ART-NET

USER MANUAL

LX113

V. 05 – 07/04/2014 2 ©Velleman nv

USER MANUAL

1. Introduction

To all residents of the European Union
Important environmental information about this product

This symbol on the device or the package indicates that disposal of the device after its lifecycle
could harm the environment. Do not dispose of the unit (or batteries) as unsorted municipal
waste; it should be taken to a specialized company for recycling. This device should be
returned to your distributor or to a local recycling service. Respect the local environmental
rules.

If in doubt, contact your local waste disposal authorities.

Thank you for choosing Luxibel®! Please read the manual thoroughly before bringing this device into
service. If the device was damaged in transit, don't install or use it and contact your dealer.

2. Safety Instructions

This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance by a person responsible for
their safety.

Children shall be supervised to ensure that they do not play with the appliance.
Never let the device run unattended.

Do not crimp the power cord and protect it against damage.
Warning! If the power cord is damaged, it must be replaced by the manufacturer, its service
agent, or similarly qualified persons in order to avoid any hazard.
Make sure that the available voltage does not exceed the voltage stated in the specifications
of this manual.
This device falls under protection class I. It is therefore essential that the device be earthed.
Have a qualified person carry out the electric connection.
Be very careful during the installation: touching live wires can cause life-threatening
electroshocks.
Do not use the device when damage to housing or cables is noticed. Do not attempt to

service the device yourself but contact an authorised dealer or service agent.

Always disconnect mains power when device not in use or when servicing or maintenance
activities are performed. Handle the power cord by the plug only.

Caution: device heats up during use. Do not touch hot surfaces. Let the device cool down
sufficiently after switching off before handling.

Indoor use only. Keep this device away from rain, moisture, splashing and dripping
liquids. Never put objects filled with liquids on top of or close to the device.

Do not stare directly at the light source, as this may cause

 epileptic seizure in sensitive people
 temporarily loss of sight (flash blindness)
 permanent (irreversible) eye damage.

 Use an appropriate safety cable to fix the device (e.g. VDLSC7N or VDLSC8N).
 Install the device at a minimal distance of 0.5 m from flammable and explosive objects or

substances.

 Respect a minimum distance of 0.5 m between the device’s light output and any illuminated surface.
 The maximum ambient temperature is 45 °C. Do not operate the device at higher temperatures.

LX113

V. 05 – 07/04/2014 3 ©Velleman nv

3. General Guidelines

Refer to the Velleman® Service and Quality Warranty on the last pages of this manual.

Keep this device away from dust and extreme temperatures. Make sure the ventilation
openings are clear at all times. For sufficient air circulation, leave at least 20" (at least
50 cm) in front of the openings.

Protect this device from shocks and abuse. Avoid brute force when operating the
device.

 Familiarise yourself with the functions of the device before actually using it. Do not allow operation

by unqualified people. Any damage that may occur will most probably be due to unprofessional use
of the device.

 All modifications of the device are forbidden for safety reasons. Damage caused by user modifications

to the device is not covered by the warranty.

 Only use the device for its intended purpose. All other uses may lead to short circuits, burns,

electroshocks, lamp explosion, crash, etc. Using the device in an unauthorised way will void the
warranty.

 Damage caused by disregard of certain guidelines in this manual is not covered by the warranty and

the dealer will not accept responsibility for any ensuing defects or problems.

 Mechanical wear and LEDs are not covered by warranty.
 A qualified technician shall install and service this device.
 Do not switch the device on immediately after it has been exposed to changes in temperature.

Protect the device against damage by leaving it switched off until it has reached room temperature.

 This device is designed for professional use on stage, in discos, theatres, etc.
 Use the appropriate power supply (see Technical Specifications below).
 Lighting effects are not designed for permanent operation: regular operation breaks will prolong their

lives.

 Keep this manual for future reference.

4. Features

 high power tri-colour LED panel for eye-candy effects, wash light or blinder effect
 Kling-Net/Art-Net support allows auto-configuration over Ethernet
 each LED controllable for pixel mapping
 DMX controlled via 3, 5, 9, 12, or 17 channels
 built-in automatic programs via master/slave or DMX with variable speed
 2 x 8 digit LCD display for easy menu setting
 COB LED for superior RGB colour mixing
 additional power output
 bracket for multiple unit connection, to create a wall
 heavy duty bracket for truss rigging
 equipped with Neutrik powerCON in/out.

LX113

V. 05 – 07/04/2014 4 ©Velleman nv

5. Overview

6. Protocols

Kling-Net

 ArKaos has designed the Kling-Net protocol to allow the distribution of real-time video data to remote

display devices, such as LEDs or LED panels, over Ethernet.

 Kling-Net allows auto configuration of display devices using an etherCON® 8P8C (RJ45) Ethernet

connection.

 The device works best with the Arkaos Mediamaster™ Pro software and its Video Mapper extension

(Mac and Windows).

 Refer to the ArKaos MediaMaster software manual for detailed instructions on programming this

product (www.arkaospro.com).

Art-Net

 Art-Net is a communication system that allows DMX512 to be sent over Ethernet.
 The Art-Net protocol was developed by the company Artistic Licence Engineering and has now been

published into the public domain.

 The protocol description is available on the following link:

www.artisticlicence.com/WebSiteMaster/User%20Guides/art-net.pdf

 Various commercial and open source programs support the Art-Net protocol.

7. Mounting the Device

 The device can be mounted in almost any orientation provided that every device is attached by the

mounting bracket.

 Mount the device in the desired angle using the included bracket.
 Have the device installed by a qualified person, respecting EN 60598-2-17 and all other applicable

norms.