LuxHome LHC100SK, LHK101SK Instruction Manual

6 Zone Wire Free

Intruder Alarm System

LHC100SK / LHK101SK

Instruction Guide

For system installations incorporating the 6 Zone Control Panel

refer to this Manual and disregard any other instructions supplied

Table of Contents

Kit Contents 3 Introduction and Overview 4

System Arming 4 Zones 4 Entry / Exit Delay 4 Zone Lockout 4 Tamper Protection 5 Voice Dialler 5 Jamming Detection 5 Battery Monitoring 5 System House Code 6

Planning and Extending your Wire Free Alarm System 7

Control Panel 8

Positioning the Control Panel 8 Installing the Control Panel 8 Setting the Control Panel House Code

Remote Control Unit 11

Setting the Remote Control 12

Passive Infrared (PIR) Movement Detectors 12

Choosing a position for the PIR Detector

12 Installing and configuring the PIR Movement Detectors 13 Testing the PIR Detectors 15

Magnetic Contact Detectors 16

Installing and setting the Magnetic Contact Detectors 16 Testing the Magnetic Contact Detectors

External Solar Siren 18

Positioning the Solar Siren 18 Installing the Solar Siren 19 Setting the Solar Siren 20 Initial Power-Up of the Solar Siren 20 Siren Service Mode 21

External Connections 21

Testing the System 22

Initial Testing 22 Testing an Installed System 22 Detector Test 23 Hard-Wired Solar Siren Test 23 Solar Siren Test 23

Control Panel LED Test 23 Voice Dialler Test 23 Factory Defaults 24 Reset Factory Default Conditions 24

Programming Instructions 25

User Access Code 25 System House Code 25 Instant Delay Zones 26 Entry / Exit Delay 26 Alarm Duration 27 Part-Arm 27 Zone Lockout 28 Entry / Exit Warning Tone 28 Jamming Detection 28 Hard-Wired Siren 29 Zone Operating Modes 29 Telephone Numbers 30 Alarm Message Play Time 31 Record Alarm Message 31 Replay Alarm Message 32 Call Routing 32 Call Attempts 32 Dial Method 33

Operating Instructions 33

Arming the System 34 Disarming the System 35 Personal Attack (PA) Alarm 35 Tamper 35 Battery Monitoring 36

Maintenance 36

Control Panel 37 Detectors and Remote Control 37 Batteries 37

Disposal and Recycling 37

Alarm Record 38

Troubleshooting 39

Extending your Alarm System

Accessories 41

Component Specification 43

Kit Contents

Alarm Components:

1 x 6 Zone LED Control Panel with Voice Dialler 2 x PIR Movement Detectors 2 x Magnetic Contact Detectors 1 x Remote Control 1 x External Solar Siren

Also included:

Power Supply Adaptor Telephone Connection Lead Instruction Guide Fixing pack

2!3

5!6

! !

2! 3! 4! 5!

[POF

6! 7!

GJSF! UBNQFS

FTD

Control Panel

PIR Movement

Detector

Magnetic Contact

Detector

Remote Control

Batteries included:

x 3

6V/1.2Ahr Sealed lead acid battery (for Control Panel and External Solar Siren)

x 2

9V PP3 Alkaline battery (for PIR Movement Detectors)

x 5

3V CR2032 Lithium cells (for Remote Control and Magnetic Contact Detectors)

External Solar Siren

Important: Please check all items listed above are included in the package.

Note: Diagrams are for illustration purposes only actual appearance may vary.

For system installations incorporating the 6 Zone Control Panel

refer to this Manual and disregard any other instructions supplied

Introduction and Overview

System Arming

The system has a ‘Full Arm’ and a ‘Part-Arm’ mode. ‘Full Arm’ will arm all zones while the ‘Part-Arm’ mode will only arm the zones that are enabled for ‘Part-Arm’.

For example:

The system could be set such that during night time, ‘Part-Arm’ would arm only zones protecting the lower floor and outbuildings, leaving the upper floor free for movement without triggering the alarm. However, when the property is left un-occupied, the ‘Full Arm’ mode will arm all zones to protect the entire property, (i.e. upper and lower floors and outbuildings).

Zones

The system incorporates 6 wire free Alarm Zones for the connection of the system Detectors that are used to independently monitor different areas of the property. In addition to standard intruder protection, each zone may also be set to operate in one of three other modes:

- Personal Attack mode provides 24 hour monitoring of any Personal Attack (PA) switches incorporated into the system.

- 24-hour Intruder mode provides 24 hour intruder protection for areas where continuous monitoring is required, (e.g. gun cabinet or safe).

- Fire mode provides 24 hour monitoring of any Fire / Smoke detectors incorporated into the system.

Entry / Exit Delay

Each zone can be programmed to be Armed in either Instant or Delay mode.

Usually the zone covering the main entrance door and the route to and from the Control Panel would be set in Delay mode. This allows time for the user to exit the property after setting the system at the Control Panel or to Disarm the system before an alarm condition is triggered when re-entering the property. The remaining zones would be set as Instant allowing them to initiate an alarm immediately a Detector on these zones are triggered.

Delay Armed zones will not become fully armed until after the Exit delay period has expired. When a Detector on a Delay Armed zone is triggered, an alarm condition will not be triggered until after the Entry period has elapsed. If the system is not disarmed during the delay period, a full alarm condition will occur when the delay period expires.

Instant Armed zones will immediately initiate a full alarm condition as soon as the zone is triggered.

Zone Lockout

If a Detector on an active zone is triggered while the system is armed, an alarm condition will occur. After the programmed alarm duration has expired the alarm will stop and the system will automatically

reset in the armed mode. Subsequent Detectors triggered will again initiate an alarm condition. If a single zone initiates an alarm condition three times then that zone will be ‘Locked Out’ and any further alarm signals from that zone will be ignored until the system is disarmed.

Note: The ‘Zone Lockout’ feature can be disabled if required.

Tamper Protection

All system devices (except Remote Control Units) incorporate Tamper protection features to protect against unauthorized attempts to interfere with the device. Any attempt to remove the battery cover from any device (except a Remote Control) or to remove the Solar Siren or Control Panel from the wall will initiate an alarm condition even if the system is Disarmed (unless the system is in Test or Programming modes).

Voice Dialler

This system incorporates a telephone voice dialler which is used to call for help and / or notify the user that the system has been triggered and an alarm has occurred.

If the Voice Dialler is enabled and an alarm condition occurs, the system will call for help using your pre- recorded alarm message and up to four telephone numbers. When the telephone voice dialler is activated it will call the first enabled number in the dialling sequence and play the recorded alarm messages for the set ‘Play Time’. The recipient can acknowledge the message by pressing the button on their telephone keypad. If the call is unanswered or an acknowledgement signal is not received then the next number in the dialling sequence will be called. The dialler will continue calling each number in turn until either all numbers in the sequence have been dialled the set number of times or the dialling sequence is cancelled by an acknowledged signal from the recipient.

Jamming Detection

In order to detect any attempts to illegally jam the radio channel used by your alarm system, a special jamming detection function is incorporated into the Control Panel and also on some Solar Siren models. If this feature is enabled, and the radio channel is jammed continuously for 30 seconds, when the system is armed, the Solar Siren will emit a pre-alarm series of rapid bleeps for 5 seconds. If the jamming continues for a further 10 seconds or more a full alarm condition will occur. In addition if the system is jammed for more than three periods of 10 seconds in a 5 minute interval, this will also generate a Full Alarm condition. The jamming detection features in the Control Panel and Solar Siren operate independently.

The Jamming Detection circuit is designed to permanently scan for jamming signals. However, it is possible that it may detect other local radio interference operating legally or illegally on the same frequency. If you are planning to operate the Jamming Detection feature we recommend that you wait at least 30 days before activating this feature, this will allow time for you to become familiar with the operation of your system.

Battery Monitoring

All devices powered by non-rechargeable batteries incorporate a battery level monitoring feature which warns when the battery status is low. In addition the Control Panel will also indicate a low battery status on any PIR Detector or Magnetic

Contact Detector on the System.

Batteries on any device indicating a low battery status must be replaced immediately.

System House Code

In order to prevent any unauthorized attempt to operate or disarm your system, you must set your system to accept radio signals only from your own devices. This is done by setting a series of eight miniature (DIP) switches in all devices (except the Control Panel) to the same ON / OFF combination (the House Code) selected by the user/installer. The Control Panel is then programmed to operate only with devices set to this House Code.

All Detectors and Remote Control Unit(s) must be set with the same House Code in order for the system to operate correctly.

Inside the Siren, Detectors and Remote Control Unit is a series of 8 DIP switches.

The House Code is set by moving each of the 8 switches in each device to the same randomly selected ON / OFF sequence. When setting the DIP switches, ensure that each switch ‘clicks’ fully into position. Use the tip of a ballpoint pen or a small screwdriver to move each switch in turn.

Note: It is recommended that the system House Code is always reset to a code other than the factory default.

Planning and Extending your Wire Free Alarm System

The example below shows a typical property incorporating the suggested positions for the Control Panel, PIR and Magnetic Detectors for optimum security. Use this as a guide for your installation in conjunction with the recommendations contained in this manual for planning your intruder alarm system.

External Solar Siren

Magnetic Contact

Detector

PIR Movement

Detector

PIR Movement

Detector

Remote Control

1 2 3 4

ZONE

5 6

FIRE TAMPER

2 3

4 5 6

7 8 9

ESC

LED Control Panel

Magnetic Contact Detector

SHED

Back Door

KITCHEN

HALL

DINING

ROOM

PIR Movement Detector

LOUNGE

GROUND FLOOR

GARAGE

PIR Movement Detector

Before attempting to install your Alarm System it is important to study your security requirements and plan your installation. The alarm system may be extended at any time to provide even greater protection by fitting additional devices to meet your personal security needs.

Control Panel

5!6

! !

FTD

Zone LEDs

2! 3! 4! 5

[POF

6! 7

GJSF! UBNQFS

Status LEDs

Keypad

Positioning the Control Panel

When choosing a suitable location for the Control Panel, the following points should be considered.

1. The Control Panel should be located in a position out of sight of potential intruders and in a safe location, but easily accessible for system operation.

2. The Control Panel should be mounted on a sound flat surface to ensure that the rear tamper switch on the Control Panel is closed when the Panel is mounted. The Control Panel should be mounted at a convenient height of between 1.5 and 2m and in a position where it will be seen each day.

Note: If small children are in the household, a further consideration should be given to keeping the units out of their reach.

3. It is recommended that the Control Panel should be positioned such that the Exit/Entry tone (emitted by the Control Panel) can be heard from outside the property.

4. The Control Panel should be mounted within a protected area so that any intruder cannot reach the Control Panel without opening a protected door or passing through an area protected by a PIR Detector when the system is armed.

5. The Control Panel must be located within reach of a mains socket.

6. If the telephone voice dialler is to be used then the Control Panel will need connecting to a convenient telephone point.

7. Do not locate the Control Unit closer than 1m to any large metallic object, (e.g. mirrors, radiators, etc) as this may affect the radio range of the Control Panel.

Installing the Control Panel

1. Undo the two captive fixing screws on top of the panel and open the cover. The cover is hinged along the bottom edge.

2. Unclip and remove the two back-up batteries on either side of the panel.

3. Hold the Control Panel in position on the wall and mark the positions of the four fixing holes. Remove the Panel and drill four 5mm holes and fit the 25mm Wall Plugs.

Note: The wall plugs supplied with the product are not suitable for plasterboard walls, if mounting the Control Panel onto plasterboard use proprietary wall plugs.

Important: Do not drill the fixing holes with the Control Panel in position; as the resulting dust and vibration may damage the Control Panel’s internal components and invalidate the guarantee.

External Tamper Switch

Jumper Link P51

Power Supply Cable Route

Upper

Keyhole

Fixing Hole

- Terminal

(Blue Lead)

+ Terminal

(Red Lead)

Lower

Fixing

Hole

Upper Keyhole Fixing Hole

+ Terminal (Blue Lead)

- Terminal (Black Lead)

Reset Jumper Link P1

Power

Supply

Jack Socket

Inside view of Control Panel

4. Fit two 18mm No. 4 screws into the top holes until almost fully home and hang the Control Panel over the screws using the two keyhole slots in the top corners of the panel casing.

5. Route the cable from the Power Supply Unit up behind and on the right hand side of the Control Panel and connect the plug to the DC power socket in the panel. Ensuring that the cable is not trapped between the Control Panel and the wall.

6. Fix the Control Panel to the wall using two 18mm No. 4 screws in the lower two fixing holes in the Control Panel and tighten the upper fixing screws until they just grip the casing. Do not over tighten the fixing screws or this may damage the casing.

7. Ensure that the ‘Reset’ and the ‘Hard-Wired Siren tamper detect’ jumper links are set in the OFF position.

8. Connect battery leads to both back-up batteries and refit batteries. Battery 1 (left): Red lead to + battery terminal Blue lead to – battery terminal

Battery 2 (right): Blue lead to + battery terminal Black lead to – battery terminal

Important: Take care when connecting battery leads to the batteries as connecting incorrectly could damage the batteries or the Control Panel.

Note: The Power LED may flash to indicate that the unit is being operated from the back-up batteries and that mains supply is not present.

9. Close the lid of the Control Panel and tighten the captive fixing screws.

10. Plug in and switch ON the Power Supply Unit, (the Power LED should illuminate).

11. If required, connect the Control Panel to the telephone line using the cable supplied by inserting small RJ11 plug into socket marked LINE located on the bottom edge of the Control Panel.

Connect the BT plug on the other end of the lead to an appropriate telephone outlet. If the cable supplied is not long enough to reach a suitable phone point then it will need extending using a coupler and extension lead (not supplied).

Note: If the Panel Tamper alarm sounds during the installation reset the alarm by pressing:

2 3 4 ,

on the Control Panel Keypad.

Setting the Control Panel House Code

With the unit in Standby mode (Power LED only illuminated).

1. Press

2 3 4 ,

. The Control Panel will beep twice and the Arm and

Part-Arm LEDs will illuminate. All Zone, Fire and Tamper LEDS will flash.

This puts the Control Panel into programming mode.

2. Press

2 3 4 ,

. The Zone LEDs 1-6, Fire and Tamper LEDs will illuminate to indicate the current House Code setting with an illuminated LED indicating a setting of ‘ON’ and LEDs not illuminated indicating a setting of ‘OFF’. For example, a house code of ‘ON’, ‘ON’, ‘ON’, ‘ON’, ‘OFF’, ‘OFF’, ‘ON’, ‘OFF’ will be indicated with zone LEDs 1- 4 illuminated, Zones 5 & 6 ‘not illuminated’, Fire Zone ‘illuminated’ and Tamper Zone ‘not illuminated’.

3. The system House Code can be set either directly at the Control Panel or via a Remote Control Unit.

At the Control Panel:

a) By pressing buttons 1-8 on the Control Panel, setting the status LEDs so that they indicate the

required house code setting. The LEDs will switch to the opposite state each time the button is pressed.

LED ON = 1, (House Code DIP Switch On) LED OFF = 0, (House Code DIP Switch Off)

b) Press

to save the new setting and return to programming mode.

c) Press

ESC!

to return to programming mode without saving.

Using a Remote Control Unit:

a) With the required House Code already set on the remote control, press the button on the

Remote Control.

The Control Panel will beep twice to acknowledge the signal.

The Zone, Fire and Tamper LED status will be updated to correspond with the House Code set on the Remote Control and now programmed into the Control Panel.

b) Press

to return to programming mode.

4. Press

ESC!

to exit programming mode and return to Standby.

5. Press

2 3 4 ,

. The Control Panel will beep and the Arm and Part-

Arm LEDs will flash.

This puts the Control Panel into test mode.

Remote Control Unit

The Remote Control Unit is used to Arm, Part-Arm and Disarm the system.

The Remote Control Unit also incorporates a Panic switch. Activating the Panic switch on the side of the Remote Control will immediately initiate a Full Alarm condition whether the system is Armed or Disarmed. The alarm can be cancelled by pressing the ‘DISARM’ button on the Remote Control or via the Control Panel.

Any number of Remote Control Units can be used with your system, providing they are all coded with the same system House Code.

The Remote Control uses a CR2032 type Lithium cell which under normal conditions will have a typical life in excess of 1 year. Under normal battery conditions the LED on the Remote control will illuminate only when a button is pressed. However, under low- battery conditions this LED will flash every time the button is pressed. When this occurs the battery should be replaced as soon as possible.

Transmit LED

Arm

Part-Arm

Disarm

Slide up to operate

Personal Attack

Setting the Remote Control

1. Remove the front cover by undoing the small screw on the rear of the Remote Control.

2. Located above the battery is a row of 8 DIP switches. Select and record a random combination of ‘ON’ and ‘OFF’ positions for the DIP switches. This will be the system House Code that enables all elements of your transmitters to communicate with the Control Panel.

Important: The House Code for your system should be changed from the factory default setting.

3. Ensure that the jumper link located immediately below the House Code DIP switches is fitted in position for use with this alarm system.

Insert the battery under the clip ensuring that the +v terminal faces upwards away from the PCB.

5. Replace the front cover and fixing screw.

Passive Infrared (PIR) Movement Detectors

PIR Detectors are designed to detect movement in a protected area by detecting changes in infrared radiation levels caused, for example, when a person moves within or across the devices field of vision.

If movement is detected an alarm signal will be generated, (if the system and alarm zone is armed).

Note: PIR Detectors will also detect animals, so ensure that pets are not permitted access to areas fitted with Passive Infra Red Detectors when the system is armed.

Any number of PIR Detectors can be used with your system, providing they are all coded with the system House Code and are mounted within effective radio range of the Control Panel.

The PIR Detector is powered by a PP3 Alkaline battery which under normal conditions will have an expected life in excess of 1 year. When the battery level drops, with the PIR Detector in normal operation mode and the battery cover fitted, the LED behind the detection window will flash. When this condition occurs, the battery should be replaced as soon as possible.

Choosing a position for the PIR Detector

The recommended position for a PIR Detector is in the corner of a room mounted at a height between 2 and 2.5m. At this height, the PIR Detector will have a maximum range of up to 12m with a field of view of 110°.

House Code

Dip Switches

Jumper Link

Battery Clip

Battery

1210

Top View

110°

12 10 8

meters

Side View

meters

More Sensitive

Less Sensitive

The Position of the PCB inside the PIR Detector can be set to 5 different positions to adjust the range of the detection pattern created by the PIR Detector. Setting the PCB in position 3 will reduce the range to approximately 9m, with position 1 providing a range of approximately 6m. The recommended position setting for the PCB is in position 5.

When considering and deciding upon the mounting position for the PIR Detector the following points should be considered to ensure trouble free operation:

1. Do not locate the PIR Detector facing a window or where it is exposed to or facing direct sunlight. PIR Detectors are not suitable for use in conservatories.

2. Do not locate the PIR Detector where it is exposed to ventilators.

3. Do not locate the Detector directly above a heat source, (e.g. fire, radiator, boiler, etc).

4. Where possible, mount the PIR Detector in the corner of the room so that the logical path of an intruder would cut across the fan detection pattern. PIR Detectors respond more effectively to movement across the device than to movement directly towards it.

5. Do not locate the PIR Detector in a position where it is subject to excessive vibration.

6. Ensure that the position selected for the PIR Detector is within effective range of the Control Panel. It is recommended that prior to installation the Detector is set and tested with the Control Panel in Walk Test mode to ensure that they are within effective range.

Note: When the system is Armed, pets should not be allowed into an area protected by a PIR Detector as their movement would trigger the PIR Detector and trigger an alarm.

Note: DO NOT fix the PIR Detector to metalwork or locate the unit within 1m of metalwork (i.e. radiators, water pipes, etc) as this could affect the radio range of the Device.

Installing and configuring the PIR Movement Detectors

Ensure that the Control Panel is in Test mode.

1. Undo and remove the fixing screw from the bottom edge of the PIR Detector. Carefully pull the bottom edge of the Detector away from the rear cover and then slide down to release the top clips.

2. Carefully drill out the required mounting holes in the rear cover using a 3mm drill according to whether the unit is being mounted in a corner or against a flat wall.

3. Using the rear cover as a template, mark the positions of the fixing holes on the wall.

4. Fix the rear cover to the wall using the two 18mm No. 4 screws and 25mm wall plugs, (a 5mm hole will be required for the wall plugs). Do not over- tighten the fixing screws as this may distort or damage the cover.

Mounting Hole

Positions

Rear Cover

Fixing Screw

+ 30 hidden pages

LuxHome LHC100SK, LHK101SK Instruction Manual

Specifications and Main Features

Frequently Asked Questions

User Manual