Lutron Electronics SVIT-DR-WH, SVIT-GRX-SH-WH, SVIT-SH-WH, SVIT-GRX-DR-WH, SVIT-MIR-SH-WH Programming Manual
...
Sivoia QED®
IR Remotes With
Favorite Preset
Button
Programming
Guide
Sivoia QED®
The Sivoia QED IR Remote with Favorite Preset Button Programming Guide is a supplement to
the Sivoia QED Wiring and Programming Guide. This guide describes the programming and setup
of the three configurations of IR remotes that have a round silver favorite preset button.
The IR Remote can be used to program and control shades/drapes in the system via a drive unit
with an IR receiver, an IR Keypad or via the IR reciever in the Contact Closure Interface.
The following chart describes the programming steps. Most of the programming can be
performed from any of the three IR remotes. The Two Shade Group Remotes (Type C) require
additional programming to define the shades/drapes that are assigned to the two sub groups
that these can control.
Favorite Preset Remote Programming Guide
IR Remote Programming Steps for IR Remotes with
Favorite Preset Button
Step Description
Addressing System
1
Assigning Drives
2
3
4 & 5
to IR Remote
Master Group
Assigning Drives
to IR Remote
Sub Groups
Storing and
Locking Presets
Type A
Single Shade Group
with Favorite Preset
SVIT-SH-WH
SVIT-DR-WH
Type B
Shade and Lighting
with Favorite Preset
SVIT-GRX-DR-WH
SVIT-GRX-SH-WH
SVIT-MIR-SH-WH
SVIT-MIR-DR-WH
Two Shade Groups
with Favorite Preset
SVIT-SC-BL-WH
SVIT-SR-BL-WH
SVIT-SH-DR-WH
SVIT-SH-SH-WH
P P P
P P P
N/A N/A
P
Type C
GROUP 1
GROUP 2
Individual Level
6
Adjust
P P P
P P P
Page 1
Sivoia QED® Favorite Preset Remote Programming Guide
1
Addressing the system
Addressing can be done with type A, B, or C remotes.
Note: Prior to addressing the system, all shades/drapes, by default, will respond to all IR
Remotes. After addressing, shades/drapes will not respond to any remote until it is assigned to
an IR Receiver, IR Keypad or contact closure interface.
(H) Press and hold button
(T) Tap button
1.1
1.2
Enter Programming Mode
Aim the Remote at the IR Receiver
and Press and Hold Open and
Close for 5 seconds. The LED’s
on the receiving device will ash
Enter Addressing Mode
Aim the Remote at the IR
Receiver and tap Open. The LED’s
on the drive will ash rapidly until
addressed. Addressing is
complete when the receiving
device starts ashing slowly.
The addressing process will take
approximately 1 minute.
H
H
H
H
H
H
A
B
T
T
C
T
A
B
C
1.3
Exit Addressing Mode
Aim the Remote at the IR Receiver
H
H
H
H
and Hold Open and Close for
5 seconds. The LED’s on the drive
will stop ashing.
A
H
H
B
C
Page 2
Sivoia QED® Favorite Preset Remote Programming Guide
2
Assigning Drives to the Master Shade Group
All three types of remotes (A, B and C) can be used to assign shades to the Master Shade Group.
However, all shades that are assigned to this group will only respond to the Type A and Type B
remotes after this step. Type C remote requires this step, in addition to step 3, to control
shades/drapes.
2.1
2.2
2.3
Enter Programming Mode
Aim the Remote at the IR Receiver
and Press and Hold Open and
Close buttons (Type A and B) or
both round silver buttons (Type C)
for 5 seconds. The LED’s on the
receiving device will ash
Enter Master Assignment Mode
Aim the Remote at the IR Receiver
and tap the Close button (Type
A and B) or while holding the
bottom round silver button, tap
close button (Type C). All
unassigned shades/drapes will
open and all assigned shades
drapes will close.
Assigning and Un-Assigning
Shades/Drapes
H
H
H
A
H
B
T
T
A
B
H
H
C
T
H
C
Select Shade/Drape to Assign
Aim the Remote at the IR Receiver
and tap the Close button until the
desired shade/drape is selected
(Tapping the Open button will
select shades/drapes in the
opposite order). Selected shade/
drape will “wiggle” or move back
and forth a few inches
continuously.
Then
Assign Selected Shade/Drape
Aim the Remote at the IR Receiver
and tap the Lower button. The
wiggling shade/drape will close to
indicate it is assigned.
Or
T
T
T
A
B
T
T
C
T
A
B
C
Page 3
Sivoia QED® Favorite Preset Remote Programming Guide
Loading...