R
StanzaTM
Installation Instructions
Occupant Copy Please Read
SZ-CI-PRG Interface
PELV (Class 2: USA) Device
15 - 24 V 200 mA
Features
• Integrates a Stanza guest room lighting control
system with a PC or other digital equipment that
supports RS232 or Ethernet TCP/IP communication.
• Provides a basic serial string command set that
allows a PC to monitor and control lighting. (Details
provided in the Lutron Integration Protocol Guide.)
• Enables use of a PC to set up and commission
Stanza systems.
• Expands Stanza basic system limits from 31 devices
to 100 devices. (Limit one SZ-CI-PRG per system.)
• An SZ-CI-PRG is required for commissioning or
system modification. Programmed and commissioned
systems do not require a SZ-CI-PRG to be present
for continued operation, unless thrid-party serial
integration is required or the number of devices
exceeds 31.
• Wireless connection allows easy mounting of interface
near integration device.
Mounting
1. Mount the interface directly on a wall, as shown in
the Mounting Diagram, using two #6 (M3) screws
(not included). When mounting, provide sufficient
space for the antenna and connecting cables.
Mount in an accessible location for convenient
access to LEDs and electrical connections.
The unit cannot be mounted in a full metal enclosure.
If mounting in a metal enclosure is necessary,
antenna must protrude out of a knockout or other
hole. The antenna may not be removed or mounted
remotely.
2. Connect wiring as shown in the Wiring Diagram.
LED 1 (Power) lights continuously when the interface
is powered.
Mounting Diagram
Wall
Control
interface
Mounting Hole Detail
0.23
(5.8)
#6 (M3) screw
recommended
(not included)
0.31 (7.9)
dia.
0.18 (4.6)
dia.
Dimensions
Dimensions are in inches (mm).
2.50
(63.5)
3.75
(95.3)
Electrical
connections
on this side
1.06
(26.9)
FCC Information
Note: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15 of
the FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio or television
reception. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution: Changes or modifications not expressly approved by
Lutron Electronics Co. could void the user’s authority to operate
this equipment. Operation is subject to the following: (1) This
device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that
may cause undesired operation.
Mounting
holes
6.0
(152.4)
4.26
(108.2)
0.75 (19.1)
5.26
(133.6)
LEDs on this
side
R
Wiring Diagram
1 2 3 4 5 6 7
CAT5 Cable:
maximum 328 ft.
(100 m)
To PC or AV equipment. For Ethernet link, use CAT5 cable (not included) to connect to
auxiliary equipment. Additional Ethernet network equipment and cables provided by others.
RS232 Cable:
maximum 50 ft.
(15 m)
COM
TxD
RxD
To PC or AV equipment: Use a standard DB9 cable
(not included), or follow the chart below.
RS232 Pin Connect Wiring
SZ-CI-PRG Typical PC or
Interface A/V equipmen
Common Com
Receive TxD
Transmit RxD
Diagnostic
LEDs
Antenna
PGM
button
(not used)
Ethernet
link/
activity
Ethernet speed
On = 100 Mbit/sec
Off = 10 Mbit/sec
RJ45 jack: Ethernet link
(to PC or A/V equipment)
PELV (Class 2: USA) Power in
200 mA 15 - 24 V
(powered by 120 V 60 Hz transformer, included).
Configuration
One SZ-CI-PRG control interface may be used per
system. The SZ-CI-PRG must be configured as a part
of the system using the StanzaTM PC software tool.
Operation
The SZ-CI-PRG receives its operating settings via a
device database transfer during system startup.
Diagnostic LED Feedback
THE SZ-CI-PRG provides 5 LEDs for user feedback
(LEDs 6 and 7 are unused):
Power LED
LED 1 lights when the unit is powered.
Ethernet Link LED
LED 2 will light when an active Ethernet link is
detected, and flash when there is link activity.
RF Activity LED
LED 3 will blink when the SZ-CI-PRG receives or
transmits an RF packet.
RS232 Link LEDs
LEDs 4 (transmit) and 5 (receive) will blink when the
RS232 link is active.
Ethernet Settings
The SZ-CI-PRG uses DHCP by default and can be
2 SZ-CI-PRG Control Interface Installation and Operation
LED 1: Power
LED 2: Ethernet link
LED 3: RF activity
LED 4: RS232 link TX
LED 5: RS232 link RX
LED 6: Unused
LED 7: Unused
communicated with using a Telnet client on port 23.
The default user login name is “lutron” and the default
password is “integration”. Login name and password
are case-sensitive. The Lutron Device IP program can
be used to change the default IP address and port
and change from DCHP to static addressing.
Internet: www.lutron.com/stanza
e-mail: product@lutron.com
Technical support: USA, Canada, Caribbean: 1.800.523.9466
Warranty: 1-year limited warranty standard. 2-year parts and labor warranty, with
8-year pro-rated parts replacement on systems that include factory startup.
For complete warranty details, see the Start-Up/Warranty document provided with
your Stanza system specification submittal information.
These products may be covered under one or more of the following U.S. patents:
5,838,226; 5,848,054; 5,905,442; 6,687,487; 6,803,728; and corresponding foreign
patents. U.S. and foreign patents pending. Lutron and the sunburst logo are
registered trademarks and Stanza is a trademark of Lutron Electronics Co., Inc.
© 2008 Lutron Electronics Co., Inc.
Mexico: +1.888.235.2910
Central/South America: +1.610.282.6701
Lutron Electronics Co., Inc.
Made and printed in U.S.A. 12/18/08
P/N 040244 Rev. A
Loading...