StanzaTM
wiring and
programming
guide
StanzaTM
Stanza Drives are available for control of Draperies and Roller Shades. Stanza Shades and Drapes
can be controlled as part of a Stanza Integrated System, incorporating Stanza lighting controls, or
as a Stanza Standalone System, without lighting controls. This Stanza Wiring and Programming
Guide describes how to set up Stanza shades and drapes in both applications.
Both the Stanza Integrated System and Stanza Standalone System utilize the same Contact
Closure Drive to motorize the shade or drape. The Drives are powered from a 24 V
supply and can be controlled via two contact closure inputs, one for open and one for close.
Drives that are part of the Stanza Integrated System receive these contact closures from a
Stanza Contact Closure Interface, SZ-IO. Drives that are part of a Stanza Standalone System
receive these contact closures from a Stanza Standalone keypad. Two types of keypads are
available: one for a single Shade or Drape application and one for a dual Shade or Drape
application.
The Shade or Drape can also be operated via an infrared Hand-Held Remote Control.
These can be used in either a Stanza Integrated System or Stanza Standalone System. Each
Drive that is being controlled, must have its own IR receiver. Two types of IR Remotes are
available: one for a single Group application and one for a Two Group application. The IR remotes
can move the Shade or Drape to the open and close limit. They also provide the additional
functions of storing and recalling a favorite preset, and setting open and close limits remotely.
Wiring and Programming Guide
---
power
Page 1
Stanza
TM Wiring and Programming Guide
Table of Contents Page
Basic Operation
Keypad Functions
IR Remote Functions
Wiring
Infrared Receiver
Stanza Standalone System
Stanza Integrated System
Contact Closure
Contact Closure Specification
3
4-5
6
7-8
9-10
11
Setting Limits
From the Drive
From an Infrared Remote
Programming
Assigning Drive to Remote Control
Storing Favorite Preset
Programming Lock Out
Restoring Default Settings
Diagnostics
SZ-IO Diagnostics Mode
Troubleshooting
Troubleshooting Chart
12
13-16
17
18-19
20
21
22
23
Stanza
Page 2
TM Wiring and Programming Guide
1
Close
Open
Close
Open
Close
Open
1.1
Stanza
•
Stanza Standalone System Keypads are available in Single Group and Dual
TM Keypads Functions
Group styles.
•
Each Shade or Drape in the system must be wired directly to the keypad to allow
it to be controlled via the keypad. No additional programming steps are required
to assign keypads to the Shade or Drape.
•
A maximum of 4 Shades or Drapes can be wired to any keypad output:
daisy chained or homerun
•
Stanza Standalone System Keypads provide contact closures to the Shade or Drape,
and require no input power.
Single Group Keypad
Provides control of one group of Shades or Drapes
Tap Open Button
Shade or Drape goes to
open limit
Tap Close Button
Shade or Drape goes to
close limit
Tapping any button while
Shade or Drape is moving
will cause it to stop.
Dual Two Group Keypad
Provides control of two groups of Shades or Drapes
Group 1
Tap Open Button
Shade or Drape goes to open limit
Tap Close Button
Shade or Drape goes to close limit
Tapping any button while
Shade or Drape is moving
will cause it to stop.
Group 2
Same functions as above
Stanza
Page 3
TM Wiring and Programming Guide
2
Close
Open
Infrared Hand Held Remote Controls | Functions
2.1
Single Group IR Remote
Provides control of one Group of Shades or Drapes
Tap Open Button
Shade or drape goes
to open limit
Tap Close Button
Shade or drape goes
to close limit
Press Raise Button
Shade or drape goes toward
open limit
Press Lower Button
Shade or drape goes toward
close limit
Tap Favorite Preset Button
Shade or drape goes to stored preset
Stanza
•
The Single Shade or Drape Remote can only be used in applications to control one group
of Shades or Drapes
•
Each Drive in the system requires its own IR Remote to allow it to be controlled via IR.
•
Open and Close limits can be set via IR Remote
•
Tapping any button while Shade or Drape is moving will cause it to stop
•
All Shades or Drapes with an IR receiver will respond to the Single Group IR Remote as shipped,
without any additional programming
Page 4
TM Wiring and Programming Guide
2
Close
Open
Sheer
Close
Open
Blackout
Infrared Hand Held Remote Controls | Functions
(continued)
2.2
Dual Group IR Remote
Provides control of two Groups of Shades or Drapes
Tap Open Button
Shade or Drape goes
to open limit
Tap Close Button
Shade or Drape goes
to close limit
Top Group
Press Raise Button
Shade or Drape goes toward
open limit
Press Lower Button
Shade or Drape goes toward
close limit
Tap Favorite Preset Button
Shade or Drape goes to stored preset
Bottom Group
Same Functions as above
Stanza
•
All Stanza Drives with an IR receiver will respond to the Top Group of buttons without any
programming
•
Shade or Drape Group Assignment is required to allow the Bottom Group of buttons to
control Shades or Drapes. Refer to Section 11, Assigning Drive to IR Remote.
•
The Dual Group Remote provides independent control of two Groups of shades or drapes
typically one Sheer Group and one Blackout Group.
•
Each Drive in the system requires its own IR Receiver to allow it to be controlled via IR.
•
Open and Close limits can be set via IR Remote
•
Tapping any button while Shade or Drape is moving will cause it to stop
Page 5
TM Wiring and Programming Guide
3
StanzaTM | Infrared Receivers
3.1
Remote IR Eye
Lutron
® offers a remote infrared eye for Stanza. It is a small dome connected to the Drive by a
22 in (560 mm) cable.
The remote infrared eye plugs into a dedicated IR connector on the Drive. Ten foot extensions are
available if the layout requires the IR eye to be located further from the Drive. The IR eye may be
located up to 50 ft (15 m) away from the Drive. Unobtrusive mounting clips and adhesive tape are
also provided.
Note: Each Stanza Drives must have its own remote IR eye to be controlled via infrared remote.
SV-IR Infrared remote eye, available in white
and royal plum. SV-IR connects to optional
extension cable (SV-IR-EXT-10) or directly
to the Drive
10 ft (3050 mm)
SV-IR-EXT-10
Up to 5 can be connected end to end
for a 50 ft (15,250 mm) extension.
Page 6
StanzaTM Wiring and Programming Guide
4
3
1
2
8
9
5
7
6
3
4
1
Stanza
TM Standalone System | Single Drive Wiring
Wire Type A
Com
24 V
IR Receiver
Close
Open
---
Terminal block of
Drive controlling single
Stanza Drapery or
Shade or Drape
Roller Shade Drive
Wire Type B
Single Group
Keypad
Single group
IR Transmitter
Com
X
24 V---
SZ-PS-1-50
Power Supply
Notes:
•
Standalone shade or drapery drives can be controlled with a keypad, IR remote, or both.
•
Pressing any button on any keypad or IR remote while the shade or drape is moving will
cause the shades or drapes in the group to stop.
•
Secondary wiring must be of type CL2, CL2P, CL2R, CL2X or other cable with equivalent
or better electrical, mechanical, and flammability ratings in accordance with local and national
electric code.
Wiring types Purpose Wire options
A Contact Closure Input/Output 18-22 AWG (1.00-0.50 mm²)
per contact closure - 250 ft (75 m) max
B Drive power (power supply to Drive) 12 AWG (4 mm²) - 250 ft (75 m) max
16 AWG (1.5 mm²) - 100 ft (30 m) max
18 AWG (1 mm²) - 50 ft (17 m) max
Stanza
Page 7
TM Wiring and Programming Guide
Loading...