Lutron Electronics Serena, Serena CS-EDU-YK-BULK, Serena CS-EDU-YQ-BULK Installation Manual

Serena® Remote-Controlled Shades
Insulating Honeycomb Shades

Motorized shade with wireless radio frequency (RF) control.

Installation Guide—Please Read Before Installing

1 Prepare to Install

Important Notes
Please Read Before Installing

!

WARNING: SHOCK HAZARD. Can cause serious injury or death. Read and follow all instructions.

!

CAUTION: RISK OF FALLING OBJECTS. Securely install the shade system per the mounting instructions.

Failure to do so could result in minor or moderate injury.

1. Read, follow, and save these instructions.

2. When mounting the brackets, make sure you are screwing into wood studs if possible. If not, you must use

appropriate fasteners (not included) for the mounting surface.

3. Make sure the brackets are aligned with each other. If not, the shade may not properly snap into the brackets.

4. Install the shade on its brackets and ensure a clear path for its travel before installing batteries.

5. Keep all LTE devices (routers, mobile phones, etc.) at least 3 ft (1 m) away from shade.

English

Included Components

•

Shade

•

Mounting brackets

•

Mounting screws

•

Spacers, if applicable

Required Tools

•

Pencil

•

Tape measure

•

Drill with 3/32" drill bit

•

#2 Phillips screwdriver

Power Source Options (sold separately)

•

Batteries (type and quantity vary with shade width):

Eight (8) AA, lithium

or

Four (4) D, alkaline

Rechargeable

batteries

Six (6) D, alkaline

Eight (8) D, alkaline

CE Information

(For model numbers CS-EDU-YK­BULK and CS-EDU-YQ-BULK)

Lutron Electronics hereby declares
that CS-EDU-YK-BULK and
CS-EDU-YQ-BULK are in compliance
with the essential requirements and
other relevant provisions of Directive
1999/5/EC. A copy of the DoC can
be obtained by writing to:

Lutron Electronics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036 U.S.A.

TRA Compliance Information

(For model number CS-EDU-YK-BULK)

TRA

•

Individual Power Supply:

CSPS-P1-1-6-WH

•

10 Output Power Supply Panel:

CSPS-P1-10-6

Registered No: ER0096954/12

Dealer No: 0016561/08

1

Lutron Electronics Co., Inc., 7200 Suter Road, Coopersburg, PA 18036-1299, U.S.A.

Printed in the U.S.A. 8/13 P/N 368-3194 Rev. B

Serena® Remote-Controlled Shades
Insulating Honeycomb Shades

Motorized shade with wireless radio frequency (RF) control.

Installation Guide—Please Read Before Installing

2 Mount Shade

2.1 Verify Correct Shade Size

Hold the shade up to the window to make sure it is the correct size.
NOTE: For outside mounting, center the shade with the window and mark the wall

or trim at each end of the shade.

English

2.2 Attach Brackets to Mounting Surface

•

Use Bracket Placement Table found on next page to position bracket

on mounting surface and mark hole locations for pre-drilling.

•

Use a level to make sure the marks are aligned.

•

Pre-drill holes for the screws. Repeat for all brackets.

•

Install the mounting brackets using the provided screws or other appropriate fasteners.

Inside Mount Outside Mount

window frame

bracket

1.25 in (32 mm)

window glass

minimum

On Trim

angled spacer*

bracket

window

trim

* If window trim is angled,

place an angled spacer
(not included) behind each
bracket. Ensure that the
trim is level before placing
the bracket flush against
its edge Pre-drill a hole
through the spacer.

wall

Outside Mount

Above Trim*

* Hole locations

should be no less
than 2.75 in (70 mm)
above the trim.

spacer

bracket

window

trim

(70 mm)

minimum

wall

2.75 in

2

Lutron Electronics Co., Inc., 7200 Suter Road, Coopersburg, PA 18036-1299, U.S.A.

Printed in the U.S.A. 8/13 P/N 368-3194 Rev. B

www.lutron.com/honeycombmaintenance

www.lutron.com/honeycombmaintenance

Serena® Remote-Controlled Shades
Insulating Honeycomb Shades

Motorized shade with wireless radio frequency (RF) control.

Installation Guide—Please Read Before Installing

English

Bracket Placement

Shade width 14.5 in – 25.875 in (368 mm – 657 mm)

1 1 1

2

Top view of shade

4 4

Front view of shade

3

Shade width 26 in – 45 in (660 mm – 1143 mm)

1

2

Top view of shade

2 in

(5 cm)

2

1

2

3

2 in

(5 cm)

2

Top view of shade and bracket

1. Bracket

2. Cord lift spool

3. Drive

4. Yellow bracket label

Shade width 45.125 in – 72 in (1146 mm – 1829 mm)

2 in

(5 cm)

1

2

Top view of shade

2

1 1

3

2 in

(5 cm)

Shade width 72.125 in – 96 in (1832 mm – 2438 mm)

1 1 1 1

Top view of shade

2 in

(5 cm)

2

2 2 2

2

2 in

(5 cm)

3

2 in

(5 cm)

1/3 w 1/3 w1/3 w

3

Lutron Electronics Co., Inc., 7200 Suter Road, Coopersburg, PA 18036-1299, U.S.A.

Printed in the U.S.A. 8/13 P/N 368-3194 Rev. B

Serena® Remote-Controlled Shades
Insulating Honeycomb Shades

Motorized shade with wireless radio frequency (RF) control.

Installation Guide—Please Read Before Installing

2.3 Mount Shade in Brackets

Holding the shade in both hands, tilt the top of the shade slightly toward the window and hook
the front edge into the brackets behind the battery release tabs ( PUSH).Then rotate the back
of the headrail up and press the bottom of the headrail firmly until you hear it click into place.
IMPORTANT: Be certain no fabric cells are caught in the brackets.

bracket

hook
front
edge

headrail - front

end cap

omitted

for clarity

English

4

Lutron Electronics Co., Inc., 7200 Suter Road, Coopersburg, PA 18036-1299, U.S.A.

Printed in the U.S.A. 8/13 P/N 368-3194 Rev. B

Serena® Remote-Controlled Shades
Insulating Honeycomb Shades

Motorized shade with wireless radio frequency (RF) control.

Installation Guide—Please Read Before Installing

3 4Install Power Source Assign Control & Program Shade

3.1 Expose Top of Headrail

Press ALL battery release tabs ( PUSH) above
the headrail. The shade will tilt forward.

Compatible Controls
(sold separately)

Pico® wireless control

Open

Raise

Close

English

Shade

Preset

Lower

Shade button

3.2 Connect Power Source

NOTE: Shades are manufactured for battery power or

wired power according to the original order. The two
types are not interchangeable or convertible.

Battery powered shades

Install the batteries as indicated in the battery holders
(so the +/- signs match). Make sure the batteries are
fully inserted into the trays. The “shade button” will
blink red/green 3 times when shade is powered.

NOTE: For best battery life, DO NOT mix old and
new batteries. Use ONLY alkaline D size batteries or
lithium AA size batteries. DO NOT install carbon-zinc or
rechargeable batteries, and DO NOT mix battery types.

Wired-power shades

With individual plug-in power supply

Uncoil the cable from
inside the headrail and
plug it into the individual
power supply. Plug the
individual power supply
into an outlet. The “shade button” will blink red/green 3
times when shade is powered.

Connected to 10-output power supply panel
For wiring instructions from a 10 output power
supply, refer to the power panel instruction guide
(P/N045-348) that came with the 10-output power
supplypanel.

3.3 Return Shade to Operating Position

Tilt the shade back into the brackets; pressing gently
until you hear a click.

e

e

Shade button

(Clear plastic button above headrail)

4.1 Assign Control

a. Press the “shade button” on one of the shades you

want to assign. The “shade button” illuminates green
while in programming mode.

NOTE: Programming mode will time out after 30

seconds of inactivity.

b. Press and hold the “Close” button on the control for

about 6 seconds, until the “shade button” blinks and
turns off—exiting programming mode.

c. Repeat steps a and b for each additional shade

assigned to the same control.

d. Repeat steps a, b, and c. for any shades assigned to

additional controls.

4.2 Adjust Upper Limit (OPTIONAL)

The shade’s upper limit is factory programmed based

on the window dimensions and mounting option.
Ifadjustment is needed, follow these steps:

a. Press the “shade button” on the shade you want to

adjust. The “shade button” illuminates green while in
programming mode.

NOTE: Programming mode will time out after

30seconds of inactivity.

b. Press and hold the “Open” and “Raise” buttons on the

control simultaneously for about 5 seconds, until the
“shade button” blinks and remainson.

c. Use the control’s “Raise” and “Lower” buttons to

adjust shade position to the upper limit you prefer.

NOTE: When raising the shades, do not compress the

fabric too much. Cells should just be gently closed.

d. Press and hold “Open” button for about 5 seconds,

until the shade button blinks and turns off, indicating
the upper limit is set.

5

Lutron Electronics Co., Inc., 7200 Suter Road, Coopersburg, PA 18036-1299, U.S.A.

Printed in the U.S.A. 8/13 P/N 368-3194 Rev. B

Serena® Remote-Controlled Shades
Insulating Honeycomb Shades

Motorized shade with wireless radio frequency (RF) control.

Installation Guide—Please Read Before Installing

English

4.3 Adjust Lower Limit (OPTIONAL)

The shade’s lower limit is factory programmed based

on the window dimensions and mounting option.
Ifadjustment is needed, follow these steps:

a. Press the “shade button” on the shade you want to

adjust. The “shade button” illuminates green while in
programming mode.

NOTE: Programming mode will time out after

30seconds of inactivity.

b. Press and hold the “Open” and “Raise” buttons on the

control simultaneously for about 5 seconds, until the
“shade button” blinks and remains on.

c. Use the control’s “Raise” and “Lower” buttons to

adjust shade position to the lower limit you prefer.

d. Press and hold “Close” button for about 5 seconds,

until the shade button blinks and turns off, indicating
the lower limit is set.

4.4 Set Preset Levels (OPTIONAL)

The preset level is preprogrammed to 50% open/closed.
a. Use the control’s “Raise” and “Lower” buttons to

adjust shade position to the level you prefer.

b. Press and hold the “Preset” button on the control for

about 5 seconds, until the “shade button” blinks and
turns off.

4.5 Set Preset on Multiple Shades to Different
Levels (OPTIONAL)

a. Repeat step 4.4:a for one shade at a time;

disconnecting the power source from all other shades
while the preset level is set. To disconnect a shade’s
power source, remove one battery, (battery models),
or, unplug the power supply, (wired models).

b. When all preset levels are set, restore power to all

shades and perform step 4.4:b to set the presetlevels.

Restoring Factory Default

•

This step will remove any controls assigned to

the shade. It will not affect the shade’s upper and
lower limits.

•

Tap the “shade button” quickly 3 times, and hold

the “shade button” after the third tap until the
“shade button” LED blinks green rapidly.

•

Immediately tap the “shade button” quickly three

more times, until the “shade button” LED blinks
green rapidly, then blinks red/green three times,
and turns off.

Removing the Shade

from the Brackets

•

Each bracket includes a release

tab at the bottom center. When
pushed, the bracket releases
the back of the headrail.

•

With the shade fully raised,

support it with one hand while
using a finger of the other hand
to press the release tab. Repeat
for each bracket on the shade.

•

Once the shade is released

from all the brackets you can lift
the shade off the brackets.

Bracket

(front view,

no shade)

Release tab

Press

release tab

(side view)

Cleaning the Fabric

To keep your shades looking their best, regularly brush
them with a feather duster or lightly vacuum them with
a clean brush-type attachment.

If your shades get a spot of dirt or a stain on them use
a clean, soft cloth and a solution of mild detergent and
warm water (1 part detergent to 3 parts water) to blot
or lightly rub the spot or stain.

DO NOT use strong detergents or spot removers, and
DO NOT have your shades dry cleaned.

IMPORTANT: Be extra careful if you are cleaning a
room darkening fabric because you could permanently
crease the fabric.

6

Lutron Electronics Co., Inc., 7200 Suter Road, Coopersburg, PA 18036-1299, U.S.A.

Printed in the U.S.A. 8/13 P/N 368-3194 Rev. B

Serena® Remote-Controlled Shades
Insulating Honeycomb Shades

Motorized shade with wireless radio frequency (RF) control.

Installation Guide—Please Read Before Installing

Troubleshooting

A B

Shade Does Not Respond Shade Is Not Level

English

IMPORTANT: The shade is designed to respond when
a control button is released. For best response during
normal operation, tap and release control buttons. DO

NOT press and hold unless instructed.
A-1 Tap the “shade button.” Does the “shade button”

LED light up green?

NO, the “shade button” LED doesn't light up at all.

Battery powered shade: 1) Make sure the

batteries are installed in the correct orientation.

2) Make sure the batteries are fresh, or install
new batteries.

Wired shade: 1) Make sure the power supply/

panel is plugged into a powered outlet. 2)
Make sure the shade power cable is properly
connected to the plug-in supply or power
panel, and system power is available.

NO, the “shade button” LED is red and/or blinking.

See “‘Shade Button’ Blink Codes”

YES Continue to A-2 below...
A-2 Make sure the control is assigned to the

shade by performing the steps in section

4.1: “Assign Controls” of the installation
instructions.

Does the “shade button” LED blink green
while assigning controls?
NO, the “shade button” LED does not respond to

control input

1) See section 2.3: “Reposition Antenna

Clip...” of the installation instructions.

2) Restore the shade’s factory default settings.

See the section: “Restoring Factory Default”
of the installation instructions.

NO, the “shade button” LED is red and/or blinking.

See “‘shade button’ Blink Codes”

YES, the “shade button” LED responds correctly,

but the shade still doesn’t move.

1) Repeat section 4.1: “Assign Controls” of the

installation instructions, and be sure to hold
the “close” button until the “shade button”
LED blinks.

2) Reset the upper and lower limits. See

sections 4.2: “Adjust Upper Limit” and

4.3: “Adjust Lower Limit” of the installation
instructions.

C-1 Leave shade in lowered position to allow

fabric to relax. Time required to relax
may vary (up to 24 hours).

C

Shade Does Not Reach
Window sill

D-1 Reset the lower limit. See section 4.3:

“Adjust Lower Limit” of the installation
instructions.

D-2 Leave shade in lowered position to allow

fabric to relax. Time required to relax may
vary (up to 24 hours).

D-3 Check the window measurements, shade

measurements, and the mounting height.

“Shade Button” Blink Codes

Red/green red/green red/green Over a 3-second

span indicates normal power-up when batteries are
inserted or power connected.

One red blink every 5 seconds = low batteries.

Install new batteries.

Solid red during shade movement = low batteries.

Install new batteries.

If you have any questions regarding your Serena
remote control shades, please visit www.lutron.com,
or call Lutron Technical Support at 1.800.523.9466.
Our technical support staff is available 24 hours a
day, 7 days a week.

7

Lutron Electronics Co., Inc., 7200 Suter Road, Coopersburg, PA 18036-1299, U.S.A.

Printed in the U.S.A. 8/13 P/N 368-3194 Rev. B

Serena® Remote-Controlled Shades
Insulating Honeycomb Shades

Motorized shade with wireless radio frequency (RF) control.

Installation Guide—Please Read Before Installing

Worldwide Headquarters | USA

Lutron Electronics Co., Inc.

7200 Suter Road

Coopersburg, PA 18036-1299 USA

TEL: [phone]

FAX: [phone]

Technical Support: 1.800.523.9466

Toll Free: 1.888.LUTRON1

EMAIL: [e-mail]

WEB: www.lutron.com/shadingsolutions

English

8

Lutron Electronics Co., Inc., 7200 Suter Road, Coopersburg, PA 18036-1299, U.S.A.

Printed in the U.S.A. 8/13 P/N 368-3194 Rev. B